show interfaces ethernet
Displays Ethernet interface information.
Parameters
Modes
Privileged EXEC mode
Examples
The following example shows information for an Ethernet interface, including whether MVRP is enabled on the interface.
device(config)# show interfaces ethernet 1/1/1
GigabitEthernet1/1/1 is up, line protocol is up
Port up for 2 hour(s) 54 minute(s) 28 second(s)
Hardware is GigabitEthernet, address is 748e.f882.0011 (bia 748e.f882.0011)
Configured speed auto, actual 1Gbit, configured duplex fdx, actual fdx
Configured mdi mode AUTO, actual MDIX
Untagged member of L2 VLAN 1, port state is FORWARDING
BPDU guard is Disabled, ROOT protect is Disabled, Designated protect is Disabled
Link Error Dampening is Disabled
STP configured to ON, priority is level0, mac-learning is enabled
Openflow is Disabled, Openflow Hybrid mode is Disabled, Flow Control is config enabled, oper enabled, negotiation disabled
Mirror disabled, Monitor disabled
Mac-notification is disabled
VLAN-Mapping is disabled
MVRP is enabled
Not member of any active trunks
Not member of any configured trunks
No port name
IPG MII 0 bits-time, IPG GMII 0 bits-time
MTU 1500 bytes, encapsulation ethernet
MMU Mode is Store-and-forward
300 second input rate: 970342992 bits/sec, 202831 packets/sec, 100.00% utilization
300 second output rate: 970343184 bits/sec, 202831 packets/sec, 100.00% utilization
2431385969 packets input, 1453965378094 bytes, 0 no buffer
Received 2431379477 broadcasts, 6491 multicasts, 0 unicasts
1 input errors, 1 CRC, 0 frame, 0 ignored
0 runts, 0 giants
2431612615 packets output, 1454102757122 bytes, 0 underruns
Transmitted 2431609583 broadcasts, 3032 multicasts, 0 unicasts
0 output errors, 0 collisions
Relay Agent Information option: Disabled
Protected: No
MAC Port Security: Disabled
This port is not being monitored for queue drops
Egress queues:
Queue counters Queued packets Dropped Packets
0 0 0
1 0 0
2 0 0
3 0 0
4 0 0
5 0 0
6 0 0
7 0 0
The following example shows detailed interface information. Note that the priority flow control (PFC) is shown as enabled and information for the unicast and multicast egress queues is shown separately.
device# show interfaces ethernet 1/1/22
10GigabitEthernet1/1/22 is up, line protocol is up
Port up for 16 minutes 1 seconds
Hardware is 10GigabitEthernet, address is aabb.ccdd.ef14 (bia aabb.ccdd.ef14)
Configured speed 10Gbit, actual 10Gbit, configured duplex fdx, actual fdx
Member of 1 L2 VLANs, port is tagged, port state is FORWARDING
BPDU guard is Disabled, ROOT protect is Disabled, Designated protect is Disabled
Link Error Dampening is Disabled
STP configured to ON, priority is level0, mac-learning is enabled
….
…..
MTU 1500 bytes
Priority-Flow-Control is Enabled
300 second input rate: 37014512 bits/sec, 9036 packets/sec, 0.38% utilization
300 second output rate: 731174584 bits/sec, 178509 packets/sec, 7.58% utilization
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 multicasts, 0 unicasts
0 input errors, 0 CRC, 0 frame, 0 ignored
0 runts, 0 giants
26055807 packets output, 13340529672 bytes, 0 underruns
Transmitted 0 broadcasts, 98 multicasts, 26055709 unicasts
0 output errors, 0 collisions
Relay Agent Information option: Disabled
UC Egress queues:
Queue counters Queued packets Dropped Packets
0 0 2074860
1 2349160 2074861
2 2349163 2074861
3 2349165 2074860
4 2349163 2074860
5 2349165 2074860
6 5461694 518651
7 6498353 0
MC Egress queues:
Queue counters Queued packets Dropped Packets
0 0 0
1 0 0
2 0 0
3 0 0
4 0 0
The following example shows information for an interface that has an ingress profile and an egress profile attached to a port.
device(config-if-e40000-1/1/1)# show interfaces ethernet 1/1/1 40GigabitEthernet1/1/1 is up, line protocol is up Port up for 5 days 12 hours 45 minutes 48 seconds Hardware is 40GigabitEthernet, address is 748e.f8f9.3d80 (bia 748e.f8f9.3d80) Configured speed 40Gbit, actual 40Gbit, configured duplex fdx, actual fdx Configured mdi mode AUTO, actual none Member of 1 L2 VLANs, port is tagged, port state is FORWARDING BPDU guard is Disabled, ROOT protect is Disabled, Designated protect is Disabled Link Error Dampening is Disabled STP configured to ON, priority is level0, mac-learning is enabled Flow Control is enabled Mirror disabled, Monitor disabled Mac-notification is disabled Not member of any active trunks Not member of any configured trunks No port name IPG MII 96 bits-time, IPG GMII 96 bits-time MTU 1500 bytes, encapsulation ethernet Ingress Profile is i1 Egress Profile is e1 300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization 300 second output rate: 0 bits/sec, 0 packets/sec, 0.00% utilization 8060797794 packets input, 1031782117647 bytes, 0 no buffer Received 0 broadcasts, 0 multicasts, 8060797794 unicasts 4 input errors, 0 CRC, 0 frame, 0 ignored 0 runts, 0 giants 8078157201 packets output, 1034004121728 bytes, 0 underruns Transmitted 0 broadcasts, 0 multicasts, 8078157201 unicasts 0 output errors, 0 collisions Relay Agent Information option: Disabled
The following example shows information for the configured bandwidth on a specific interface. In this example the configured interface bandwidth value is 2000 kilobits per second.
device# show interfaces ethernet 1/1/1 GigabitEthernet1/1/1 is disabled, line protocol is down STP Root Guard is disabled, STP BPDU Guard is disabled Hardware is GigabitEthernet, address is 748e.f82a.6a00 (bia 748e.f82a.6a00) Configured speed auto, actual unknown, configured duplex fdx, actual unknown Interface bandwidth is 2000 kbps
The following example shows information for an Ethernet interface, including cable signal error scanning information.
device# show interface ethernet 1/1/3 2.5GigabitEthernet1/1/3 is up, line protocol is up Port up for 10 minute(s) 56 second(s) Hardware is 2.5GigabitEthernet, address is 609c.9fee.44f2 (bia 609c.9fee.44f2) Configured speed auto, actual 1Gbit, configured duplex fdx, actual fdx Configured mdi mode AUTO, actual MDIX EEE Feature Disabled Untagged member of L2 VLAN 1, port state is FORWARDING BPDU guard is Disabled, ROOT protect is Disabled, Designated protect is Disabled Link Error Dampening is Disabled Cable Signal Error Scanning is Enabled, Scan_Interval: 5 sec Cable Signal Error Count: 4, Last Cable Signal Error Reported Time: 11 minute(s) 32 second(s) ago STP configured to ON, priority is level0, mac-learning is enabled MACsec is Disabled Flow Control is config enabled, oper enabled, negotiation disabled Mirror disabled, Monitor disabled Mac-notification is disabled VLAN-Mapping is disabled Not member of any active trunks Not member of any configured trunks No port name IPG MII 0 bits-time, IPG GMII 0 bits-time MTU 1500 bytes MMU Mode is Store-and-forward ...
The following example shows information for an Ethernet interface, including the information that cable signal error scanning is disabled.
device# show interface ethernet 1/1/3 2.5GigabitEthernet1/1/3 is up, line protocol is up Port up for 10 minute(s) 56 second(s) Hardware is 2.5GigabitEthernet, address is 609c.9fee.44f2 (bia 609c.9fee.44f2) Configured speed auto, actual 1Gbit, configured duplex fdx, actual fdx Configured mdi mode AUTO, actual MDIX EEE Feature Disabled Untagged member of L2 VLAN 1, port state is FORWARDING BPDU guard is Disabled, ROOT protect is Disabled, Designated protect is Disabled Link Error Dampening is Disabled Cable Signal Error Scanning is Disabled STP configured to ON, priority is level0, mac-learning is enabled MACsec is Disabled Flow Control is config enabled, oper enabled, negotiation disabled Mirror disabled, Monitor disabled Mac-notification is disabled VLAN-Mapping is disabled Not member of any active trunks Not member of any configured trunks No port name IPG MII 0 bits-time, IPG GMII 0 bits-time MTU 1500 bytes MMU Mode is Store-and-forward ...
History
| Release version | Command history |
|---|---|
| 08.0.20 | The command ouptut was modified to include PFC status and separate unicast and multicast egress queues. |
| 08.0.30 | The command ouptut was modified to include configured bandwidth status. |
| 08.0.95 | The command ouptut was modified to display the status of MVRP (enabled or disabled) on an interface. |
| 08.0.95h | The command ouptut was modified to include information for cable signal error scanning status and information. |
| 09.0.10d | The command ouptut was modified to include information for cable signal error scanning status and information. |