jp-policy
jp-policy
[
rp-address
]
[
acl-name
|
acl-number
]no jp-policy
[
rp-address
]
[
acl-name
|
acl-number
]The join and prune policy is not congifured for IPv4 PIM or PIMv6.
PIM router configuration mode
IPv6 PIM router configuration mode
ACL rules are used to configure which multicast group addresses PIM (*, G) are sent to the RP, and which are to be dropped or allowed. Multicast group address and prefixes are configured as destination IP addresses and prefixes in the extended ACL rules. Because this ACL is used for PIM (RP, G) filtering, the source IP address/prefixes in the case of extended ACL rules are ignored.
Only one ACL can be applied to an RP addres. The configuration is limited to a maximum 64 RPs in a given VRF.
If the specified ACL is not configured, then the PIM (*, G) Join and Prune messages sent to that RP for all multicast group addresses are dropped.
Only one ACL can be applied to both PIM (*, G) and (S, G) Join and Prune filtering at a time.
Standard and extended ACLs are supported for IPv4 (RP, G). Group addresses and prefixes can be configured as the source IP addresses in the standard ACL rules.
The no form of the command
unconfigures perviously configured IPv4 PIM or PIMv6 Join and Prune policies.
The following example configures the PIM (RP, G) Join and Prune policy for a non-default VRF instance. An ACL number is specified.
device# configure terminal device# router pim vrf blue device(config-pim-router-vrf-blue)# jp-policy 10.9.9.9 1 device(config-pim-router-vrf-blue)# jp-policy 22.9.9.9 22 device(config-pim-router-vrf-blue)# jp-policy 100.9.9.9 1
The following example configures the PIM (*, G) and (S, G) Join and Prune policy for the default VRF. An ACL name is specified.
device# configure terminal device(config)# router pim device(config-pim-router)# jp-policy wg-sg-acl
The following example configures the PIMv6 (RP, G) Join and Prune policy for a non-default VRF instance in IPv6 PIM router configuration mode. An ACL name is specified.
device# configure terminal device# ipv6 router pim vrf blue device(config-ipv6-pim-router-vrf-blue)# jp-policy 10:10::10:10 testacl device(config-ipv6-pim-router-vrf-blue)# jp-policy 22:9::9:9 testacl device(config-ipv6-pim-router-vrf-blue)# jp-policy 100:9::9:9 testacl
The following example unconfigures a previously configured PIM (RP, G) Join and Prune policy for a non-default VRF instance.
device(config-pim-router-vrf-blue)# no jp-policy 10.9.9.9 1 device(config-pim-router-vrf-blue)# no jp-policy 22.9.9.9 22 device(config-pim-router-vrf-blue)# no jp-policy 100.9.9.9 1
The following example unconfigures a previously configured PIM (*, G) and (S, G) Join and Prune policy.
device# configure terminal device(config)# router pim device(config-pim-router)# no jp-policy wg-sg-acl
The following example configures PIMv6 (*, G) and (S, G) Join and Prune policy for the default VRF. An ACL name is specified
device# configure terminal device(config)# ipv6 router pim device(config-ipv6-pim-router)# jp-policy wg-sg-acl
| Release version | Command history |
|---|---|
| 09.0.10 | This command was introduced. |