forwarding-profile
forwarding-profile
{
profile1
|
profile2
|
profile3
|profile4
}no forwarding-profile
{
profile1
|
profile2
|
profile3
|profile4
}The default forwarding profile is profile1.
Global configuration mode
This command is not supported for RUCKUS ICX 7150 and ICX 7650 devices.
The profile4 keyword is not supported for RUCKUS ICX 8200, ICX 8100, and ICX 7550 devices.
This command can be used only during the
initialization process. The selected forwarding profile is available after a reload.
After using the forwarding-profile command, you must use the write-memory and
reload
commands to place the change into effect.
When the forwarding profile is changed using this command, the maximum system parameters for IPv4 routes, IPv6 routes, IGMP groups, MLD groups, PIM mcache, and PIMv6 mcache take the value from the configured profile. The IP route default VRF, IP route VRF, IPv6 route VRF, and IPv6 default VRF are reset.
For ICX 8200 devices, non-optimization of Multicast snooping and Routing is not supported for Profile 3.
System-max Entries Set for a Forwarding Profile for ICX 8200 Devices
System-max Entries Set for a Forwarding Profile for ICX 8100 Devices
System-max Entries Set for a Forwarding Profile for ICX 7850 Devices
System-max Entries Set for a Forwarding Profile for ICX 7550 Devices
When
profile3 is used for
ICX 7850 devices, it is recommended to configure the maximum number of IPv6 neighbors to 65536.
Refer to the
system-max ip6-neighbor command for more information.
When profile3 is used for ICX 7850 devices, PIMv4 and PIMv6 can simultaneously scale to 8192 mcache entries each.
When uRPF is enabled, scaling numbers for IPv4 and IPv6 routes are halved for ICX 7850 devices.
The no form of the command
restores the default forwarding profile, profile1.
The following example configures the predefined forwarding profile “profile2” for an ICX 7850 device.
ICX7850# configure terminal ICX7850(config)# forwarding-profile profile2 Perform a write mem and reload for profile2 profile to take effect
The following example configures the default forwarding profile “profile1” for an ICX 7850 device if another forwarding profile has already been configured.
ICX7850# configure terminal device(config)# forwarding-profile profile1 Perform a write mem and reload for profile1 profile to take effect
The following example configures the predefined forwarding profile “profile3” for an ICX 7550 device.
ICX7550# configure terminal ICX7550(config)# forwarding-profile profile3 Perform a write mem and reload for profile3 profile to take effect The profile supports the following values Parameter-name profile3 mac 32768 ip-route 21504 ip6-route 17408 igmp-snoop-mcache 6144 igmp-snoop-group-add 6144 mld-snoop-mcache 8192 mld-snoop-group-addr 8192 pim-hw-mcache 6144 pim6-hw-mcache 2048 hw-ip-next-hop 21504 Default and Max values of the following system-max parameters will be adjusted as shown below These system parameters will get reset to their default values. If required, please reconfigure them after reload. System Parameter Default Max imum ip-route-default-vrf 10752 215 04 ip-route-vrf 672 215 04 ip6-route-default-vrf 4975 174 08 ip6-route-vrf 2487 174 08 The following configuration will get reset to their default values. If required, please reconfigure them after reload. address-family ipv4|ipv6 max-route, ip igmp max-group-addresses, ipv6 mld max-group-addresses