show ip

Displays global IP configuration information.
Syntax
show ip
Modes

User EXEC mode

Global configuration mode

Usage Guidelines

This command has additional options, which are explained in separate command pages.

The show ip command displays the following information:

Field

Description

Global settings

ttl

The Time-To-Live (TTL) for IP packets. The TTL specifies the maximum number of router hops a packet can travel before reaching the device. If the packet TTL value is higher than the value specified in this field, the device drops the packet.

arp-age

The ARP aging period, which specifies how many minutes an inactive ARP entry remains in the ARP cache before the router ages out the entry.

bootp-relay-max-hops

The maximum number of hops away a BootP server can be located from the device and still be used by the router clients for network booting.

router-id

The 32-bit number that uniquely identifies the device.

By default, the router ID is the numerically lowest IP interface configured on the router.

enabled

The IP-related protocols that are enabled on the router.

disabled

The IP-related protocols that are disabled on the router.

Static routes

Index

The row number of this entry in the IP route table.

IP Address

The IP address of the route destination.

Subnet Mask

The network mask for the IP address.

Next Hop Router

The IP address of the router interface to which the device sends packets for the route.

Metric

The cost of the route. Usually, the metric represents the number of hops to the destination.

Distance

The administrative distance of the route. The default administrative distance for static IP routes in RUCKUS ICX devices is 1.

Policies

Index

The policy number. This is the number you assigned the policy when you configured it.

Action

The action the router takes if a packet matches the comparison values in the policy. The action can be one of the following:

  • deny: The router drops packets that match this policy.
  • permit: The router forwards packets that match this policy.

Source

The source IP address the policy matches.

Destination

The destination IP address the policy matches.

Protocol

The IP protocol the policy matches. The protocol can be one of the following:

  • ICMP
  • IGMP
  • IGRP
  • OSPF
  • TCP
  • UDP

Port

The Layer 4 TCP or UDP port the policy checks for in packets. The port can be displayed by its number or, for port types the router recognizes, by the well-known name. For example, TCP port 80 can be displayed as HTTP.

Note: This field applies only if the IP protocol is TCP or UDP.

Operator

The comparison operator for TCP or UDP port names or numbers.

Note: This field applies only if the IP protocol is TCP or UDP.
Examples

The following example shows sample output of the show ip command in which the status of the next hop or ARP port movement syslog message (enabled) is displayed. 

device(config)# show ip
Global Settings
  ttl: 64, arp-age: 10, bootp-relay-max-hops: 4
  router-id : 10.1.1.1
  enabled : BGP4  UDP-Broadcast-Forwarding  Source-Route  Load-Sharing  RARP  VSRP
  arp-port-move-syslog
  disabled: Route-Only  Directed-Broadcast-Forwarding  IRDP  Proxy-ARP  RIP  OSPF
  VRRP  VRRP-Extended  ICMP-Redirect  add-host-route-first

The following example shows sample output of the show ip command in which the status of the next hop or ARP port movement syslog message (disabled) is displayed. 

device(config)# no ip arp port-move-syslog 
device(config)# show ip
Global Settings
  ttl: 64, arp-age: 10, bootp-relay-max-hops: 4
  router-id : 10.1.1.1
  enabled : BGP4  UDP-Broadcast-Forwarding  Source-Route  Load-Sharing  RARP  VSRP

  disabled: Route-Only  Directed-Broadcast-Forwarding  IRDP  Proxy-ARP  RIP  OSPF
  VRRP  VRRP-Extended  ICMP-Redirect  add-host-route-first arp-port-move-syslog
History
Release Command History
08.0.70 This command was modified to display the status of the next hop or ARP port movement syslog message (enabled or disabled).
Parent topic: Show Commands