spx interactive-setup

Allows you to configure several options interactively: change existing PE IDs, discover and assign IDs to new PE units, and convert existing or new standalone devices to PE units.
Syntax
spx interactive-setup
Modes

Privileged EXEC mode

Usage Guidelines

You cannot use the spx interactive-setup or the zero-touch-enable command from a device running FastIron release 08.0.90 or later to discover PE candidates running a pre-08.0.90 release, due to a difference in message types beginning with the FastIron 08.0.90 release. Be sure to load the same FastIron 08.0.90 or later image to the potential PE units before executing either command.

You can abort SPX interactive-setup at any time by pressing <CTRL>-C.

SPX interactive-setup will abort afer two minutes of inactivity.

You can use SPX interactive-setup for configuration that is not possible with SPX zero-touch features.

You can use SPX interactive-setup to handle invalid topologies by specifying units to form a valid topology.

If not all units are discovered when you run spx interactive-setup, you can run the utility again.

Examples

Consider replacing deprecated example with a similar example based on an ICX 7650 CB stack. Be sure to replace the exposed ICX 7750 CB example when a replacement can be provided by a SME.
The following example shows options available under spx interactive-setup. 

device# spx interactive-setup
You can abort interactive-setup at any stage by <ctrl-c>
0: quit
1: change PE IDs
2: discover and convert new units (no startup-config flash) to PEs
3: discover and convert existing/new standalone units to PEs
Please type your selection:

Keep this example in as is and replace with an ICX 7650 CB stack example when one is made available. At least this much is needed to understand how the command works.
The following example uses spx interactive-setup to discover and add a connected ring of two PEs (ICX 7250 units). 

device# configure terminal
device(config)# spx cb-enable
System is now in 802.1br control bridge (CB) mode.
device(config)# spx cb-config
device(config-spx-cb)# spx-port 1/1/3
device(config-spx-cb)# spx-port 1/1/16
device# spx interactive-setup
You can abort spx interactive-setup at any stage by <ctrl-c>
0: quit
1: change PE IDs
2: discover and convert new units (no startup-config flash) to PEs
3: discover and convert existing/new standalone units to PEs
Please type your selection: 2
Probing topology to find new units...
Horizontal bars link to discovered units. Vertical bars link to CB or PEs.
#1: icx7250-24-port-management-module CC4E.24DC.E9CE
#2: icx7250-24-port-management-module CC4E.24DC.F166
1/1/3         1/1/16
  |             |
  |             |
2/3           2/4
+----+        +----+
| 1  |2/5==2/5| 2  |
+----+        +----+

Discovered 1 chain/ring
chain #0: Do you want to select this chain?(enter 'y' or 'n'): y
#1: icx7250-24-port-management CC4E.24DC.E9CE, type an ID (No: 0, default: 17): <-- You can change
the default id,
or just type
enter to use
the default
#2: icx7250-24-port-management CC4E.24DC.F166, type an ID (No: 0, default: 18):
2 unit(s) selected: #1: ID=17, #2: ID=18,
#1 #2
          +----+        +----+
1/1/3--2/3| 17 |2/5==2/5| 18 |2/4--1/1/16
          +----+        +----+
Will produce the above topology. Do you accept it? (enter 'y' or 'n'): y
spx interactive-setup discovers 1 chain(s). valid #=1, selected #=1
Send reload to chain0: #1 CC4E.24DC.E9CE ID=17, D0: 2/3, D1: 2/5 to 2/6 2/8
#2 CC4E.24DC.F166 ID=18, D0: 2/5 to 2/6 2/8, D1: 2/4
Exit spx interactive-setup, reason: 1/1/3 (linking to cc4e.24dc.e9ce) down
Exit spx interactive-setup, reason: 1/1/16 (linking to cc4e.24dc.f166) down
Exit spx interactive-setup, reason: 1/1/3 (linking to cc4e.24dc.e9ce) down
Exit spx interactive-setup, reason: 1/1/16 (linking to cc4e.24dc.f166) down
U18-MSG: PS 1, Internal Power supply is up.
Sica Unit id:18, PoD License Capacity:8
Sica Unit id:17, PoD License Capacity:8
device# show spx
T=42m39.1: alone: standalone, D: dynamic cfg, S: static
ID Type Role Mac Address Pri State Comment
1 S ICX7750-48XGF alone cc4e.24d2.2c00 0 local Ready
17 D ICX7250-24 spx-pe cc4e.24dc.e9ce N/A remote Ready
18 D ICX7250-24 spx-pe cc4e.24dc.f166 N/A remote Ready
   +---+
2/1| 1 |2/4
   +---+
          +----+        +----+
1/1/3--2/3| 17 |2/5==2/5| 18 |2/4--1/1/16
          +----+        +----+
History
Release version Command history
08.0.50 This command was introduced.
Parent topic: Commands Si - Z