LAG Settings

Create and configure LAGs for all RUCKUS Edge devices in this cluster if needed, or click Next to skip:
  1. Click Add LAG to create a new LAG for the first node in the cluster.
    This displays the Add LAG sidebar.
  2. Enter the following details to add a LAG to the RUCKUS Edge device.
    Note: Adding ports already configured to a LAG displays a warning that the existing configuration will be removed.
    • LAG Name: Select a name for the LAG from the drop-down list. The LAG name is a numeric value from 0 through 3. After the LAG is created, you cannot edit the LAG name.
    • Description: Enter a meaningful, short description about the LAG.
    • LAG Type: The default type is LACP (Dynamic) as RUCKUS Edge does not support static LAG.
    • Mode: Click the drop-down list and select the mode of the LAG. There are two modes:
      • Active: Always initiates Link Aggregation Control Protocol (LACP) and Protocol Data Unit (PDU) to the peer. This is the default mode for RUCKUS Edge LACP LAG.
      • Passive: Never initiates any LACP exchange on its own. It responds only after receiving LACP and PDU messages from the peer/partner device. Hence, both peers cannot be in passive mode. At least one of the peers should be configured in active mode.
    • Timeout: Time interval indicates how long the LACP should wait before declaring the partner as down. This interval also defines the rate at which LACP hello packets are exchanged among the peers. There are two types of timeout.
      • Long: The value of this timeout is 90 seconds. Hello packets are transmitted every 30 seconds. After 3 misses (3*30s = 90 seconds), the peer information is flushed and the LACP state is declared as down.
      • Short: The value of this timeout is 3 seconds. Hello packets are transmitted every 1 second. After 3 misses (3*1s = 3 seconds), the peer information is flushed. This is the default timeout for RUCKUS Edge LACP LAG.
    • Select LAG Members: A physical port associated with a LAG interface is a LAG member. To associate LAG members, select the ports to be members of this LAG. The Port Enabled option beside the respective port is enabled by default. Toggle the button to disable the port. Selecting Port1 enables Access port and Port2 enables Core port option. Select both ports Port1 and Port2 if Access and Core separation is not intended.
      Note: Access/Core separation is part of the SD-LAN feature. Refer Software Defined Local Area Network, for more information.
    • Port Type - Select the type of port from the drop-down list.
      Note: A maximum of two WAN interfaces are allowed.

    Port Type Configuration

    Port Type Use port as IP Settings
    WAN Not applicable: The WAN port type does not support access and core separation. Both roles are performed in the same port.
    • Choose IP Assignment
      • DHCP: Automatically provides an IP address from the host.
      • Static/Manual: Enter the following:
        • IP Address
        • Subnet Mask
        • Gateway
    • Click the Use NAT Service toggle to enable the option and enter the following NAT IP Addresses Range:
      • Start
      • End
    LAN Applicable to SD-LAN services only.

    Select the required checkboxes:

    • Core port
    • Access port

    Hover over the icon next to Access port and click See the compatibility requirements to check the Compatibility Requirement for Access/Core separation.

    • IP Address
    • Subnet Mask
    Cluster Not Applicable Choose IP Assignment
    • DHCP: Automatically provides IP address with the host IP address.
    • Static/Manual: Enter the following:
      • IP Address
      • Subnet Mask
  3. Click Add.
    The Add LAG sidebar closes and the newly added LAG appears in the LAG Settings list.
  4. Click the sub-tab for the second node in the cluster, then repeat and to add a LAG to the second node.
    RUCKUS One performs a compatibility check of the configurations on each node. If a mismatch is detected, it displays a warning message labeled Mismatch. You can click on the See Details option to view the root cause and specifics of the mismatch to quickly identify the discrepancies.

    You can Edit or Delete the offending LAG by selecting the checkbox adjacent to the LAG. After the mismatches are resolved, the compatibility check result changes to Pass.

    LAG Nodes Compatibility Check with Mismatch

  5. Click Next.
    The Port General Settings page is displayed.