Configuring a Cluster for Active Standby High Availability Deployment without a LAG interface

This section describes configuring a cluster for Active Standby high availability without a LAG interface in RUCKUS Edge.
You can choose to configure a cluster without a LAG when the cluster for HA ensure redundancy and failover capabilities including link failures.

Configure a dual-node RUCKUS Edge cluster without LAG as follows:

  1. Log in to the RUCKUS One web user interface with your credentials.
  2. On the RUCKUS One navigation bar, click Gateway > RUCKUS Edge.
    This displays the RUCKUS Edge page.
  3. Select the checkbox adjacent to the RUCKUS Edge cluster name. This highlights the Edit and Run Cluster & RUCKUS Edge configuration wizard options.
    Note: The Node Status is Need port config.

    Run Cluster and RUCKUS Edge Configuration Wizard

  4. Click the Run Cluster & RUCKUS Edge configuration wizard option.
    This displays the Cluster & RUCKUS Edge Configuration Wizard screen of the selected RUCKUS Edge device with the two options.
    • LAG, Port and Virtual IP Setting
    • Cluster Interface Settings
  5. Select the LAG, Port & Virtual IP Settings checkbox and click Next to start the configuration.

    Cluster and RUCKUS Edge Configuration Wizard

Link Aggregation Group (LAG), Port and Virtual IP Settings

This section describes configuring LAG, Port and Virtual IP Settings.
  1. LAG Settings: To configure a cluster without a LAG interface, click Next.
  2. Ports General Settings: Configure the port general settings for all RUCKUS Edge devices.
    • Description: Enter a meaningful description for the port settings.
    • Port Type: Select a port type from the drop-down menu. If a LAG is not configured, it is necessary to configure at least one port to function as a LAN port or core port in order to form a cluster. To configure one port as core port, follow these steps:
      1. In the sub-tab for one RUCKUS Edge device (node), select the Port1 sub-tab and enter the description.
      2. In the Port Type drop-down menu, select LAN and select the check box Use this port as Core Port. By default, the Port Enabled option is enabled.
      3. Remain in the same device (node) sub-tab, then select the Port2 sub-tab and enter the description.
      4. In the Port Type drop-down menu, select Cluster. By default, the Port Enabled option is enabled.

        Configuring Ports Without a LAG - 1

        Configuring Ports Without a LAG - 2

      5. Repeat steps through to configure ports for the second RUCKUS Edge device (node) in the cluster, then click Next.
      Note: Use this port as Core Port is utilized for the SD-LAN service, the core port on this RUCKUS Edge establishes tunnels for directing data traffic effectively.
    • IP Settings: Configure the IP settings for the cluster ports:
      • IP Assignment: Select DHCP or Static/Manual. If static/manual IP is selected, then enter the IP Address, Subnet Mask and Gateway of the port.
        Note: The Gateway field is available only when the Port Type is set to LAN.
    • Click Next.
  3. Cluster Virtual IP: This section displays the configured Node Name, Interface and IP Subnet Mask. Enter the Virtual IP Address.
    To edit/delete the configuration, click Change or Clear.
    • Virtual IP Address: Enter the VRRP IP address for switches to connect to RUCKUS Edge.
    • Failover Settings: Drag the HA Timeout timeline bar to adjust the amount of time allowed to elapse before triggering a failover.
      Note: An HA failover time of 6 seconds or longer is recommended for RUCKUS Edge use-cases. A timer set to less than this is very aggressive and could potentially cause VRRP issues in some networks. HA timeout refers to the time period within which a node must receive a periodic heartbeat signal from the active node. If the timer expires prior to receiving a heartbeat signal, then the system initiates the failover process to select the next active node and maintain system functionality.

      Cluster Virtual IP

    Click Next.

  4. Summary: This displays the configuration settings on the cluster. View and verify the configuration details and click Apply & Continue to proceed to the Cluster Interface Settings configuration, or Apply & Finish to complete the LAG, Port and Virtual IP Settings configuration without proceeding to the Cluster Interface Settings configuration.

    Summary of the Cluster Configuration without a LAG

    Note: After the nodes are configured, the Node Status changes from Needs Port Config to Operational, Cluster Status is Ready 2/2, and HA Status reflects node 1 is Active and node 2 is Standby.

    Nodes Status is Operational

Cluster Interface Settings

The cluster interface is used as a communication channel between the RUCKUS Edge devices.
This section describes configuring Cluster Interface Settings.

After configuring the LAG, Port and Virtual IP Settings and clicking Apply & Continue (as described in Link Aggregation Group (LAG), Port and Virtual IP Settings), select the Cluster Interface checkbox and click Next. This displays Cluster Interface page containing a tab for each RUCKUS Edge device in the cluster for a non-LAG case as shown in .

  1. On the first device tab, configure these settings:
    • Set cluster interface on: Use the drop-down menu to select the port that want to serve as the cluster interface to the other RUCKUS Edge device.
    • Enter the IP Address and Subnet Mask address of cluster interface port.
  2. Repeat on the second device tab.
  3. Click Apply & Finish.