Creating an AP Zone

The process of defining a logical grouping of access points with shared configuration settings such as WLANs, radio policies, authentication methods, and services. AP Zones simplify deployment and management by allowing consistent configurations to be applied across multiple access points, reducing operational effort and ensuring uniform network behavior. profiles.

To create an AP Zone, perform the following -

  1. From the main menu, navigate to Network > Wireless > Access Pointsto create an AP Zone. This displays the Access Points page.
  2. In the System tree, select the location to create the zone and click the icon. This displays the Create Domain window.
  3. In the Create Domain window, select the Type as Zone. The title of the window changes from Create Domain to Create Zone.

    Create Zone

  4. To create a new zone, configure fields as per the below details.

    AP Zone Details

    Field Description Your Action
    Name Indicates the name of the zone/AP group. Enter a name.
    Description Indicates the short description assigned to the zone or AP group. Enter a brief description
    Type Indicates if you are creating a domain, zone or an AP group. Appears by default. You can also choose the option.
    Parent Group Indicates the parent AP group. Appears by default.
    Configuration > General Options
    AP Firmware Indicates the firmware to which it applies. Select the firmware.
    Country Code Indicates the country code. Using the correct country code helps ensure that APs use only authorized radio channels. Select the country code.
    Location Indicates the generic location of the zone. Enter the location.
    Location Additional Information Indicates detailed location. Enter additional location information.
    GPS Coordinates Indicates the geographical location. Enter the following coordinates:
    • Longitude
    • Latitude
    • Altitude
    AP Admin Logon Indicates the admin logon credentials. Enter the Logon ID and Password.
    AP Time Zone Indicates the time zone that applies. Select a time zone, and the enter the details as required.
    AP IP Mode Indicates the IP version that applies. Select the IP version. IPv6, IPv4 and dual addressing modes are supported.
    Historical Connection Failures Allows the zone APs to report client connection failures so that the administrator can view past connection problems from the Troubleshooting menu. Click the button.
    DP Group Specifies the a group of data plane nodes used for traffic forwarding and tunnel management. Select the DP group from the drop-down list.
    Enhanced Secure Mode Enables additional security settings and restrictions to strengthen system protection. By default, this option is disabled. Click the toggle button to enable.
    SSH Tunnel Encryption Enables encryption for SSH tunnel communication. Select the required option:
    • AES 128
    • AES 256
    Cluster Redundancy Provides cluster redundancy option for the zone.
    Note: Cluster redundancy is supported only on SZ300 and vSZ-H.

    Select the required option:

    • Zone Enable
    • Zone Disable
    Configuration > Radio Options
    Channel Range (2.4G) Indicates that you want to override the 2.4GHz channel range that has been configured for the zone to which this AP group belong. Select Select Channel Range (2.4G) check boxes for the channels on which you want the 2.4GHz radios of managed APs to operate. Channel options include channels 1 to 11. By default, all channels are selected.
    DFS Channels Allows ZoneFlex APs to use DFS channels. Select the check box.
    5.8 Ghz Channels Provides C-band support for all Outdoor APs and the following Indoor APs: R310, R510.

    Note: This feature is available only for countries that support 5.8Ghz channel. For example, UK provides indoor AP—5.8Ghz channel support.

    Select the Allow 5.8Ghz channels check box.
    5.8 Ghz Channels License Enables full TX Power Adjustment for C-band channels.
    Note: This feature is supported only for UK.
    Select the Allow 5.8Ghz channels use full power check box.
    Channel Range (5G) Indoor Indicates the channels on the 5GHz radio that you want managed indoor APs to operate. Select the check boxes.
    Channel Range (5G) Outdoor Indicates the channels on the 5GHz radio that you want managed outdoor APs to operate. Select the check boxes.
    Radio Options b/g/n (2.4 GHz) Indicates the configuration options for the 2.4 GHz radio. Select the following options:
    • Channelization—Set the channel width used during transmission to either 20 or 40 (MHz), or select Auto to set it automatically.
    • Channel—Select the channel to use for the b/g/n (2.4GHz) radio, or select Auto to set it automatically.
    • Auto cell sizing— Select this option to enable APs to share information on interference seen by each other and dynamically adjust their radio Tx power and Rx parameters to minimize interference. Enabling this option, disables the TX Power Adjustment configuration.
      Note: Ensure that Background Scan is enabled.
    • TX Power Adjustment—Select the preferred TX power, if you want to manually configure the transmit power on the 2.4GHz radio. By default, TX power is set to Full on the 2.4GHz radio.
      Note: If you choose Min, the transmit power is set to 0dBm (1mW) per chain for 11n APs, and 2dBm per chain for 11ac APs. If you choose Max, the transmit power is set to the max allowable value according to the AP's capability and the operating country's regulations.
    Radio Options a/n/ac (5GHz) Indicates the configuration options for the 5GHz radio. Select the following options:
    • Channelization—Set the channel width used during transmission to either 20, 40, 80, 80+80, 160 (MHz), or select Auto to set it automatically.
    • Channel—For Indoor and Outdoor, select the channel to use for the a/n/c (5GHz) radio, or select Auto to set it automatically.
    • Secondary Channel (80+80)—For Indoor and Outdoor, the default secondary channel to use for the a/n/c (5GHz) radio, is set as Auto.
    • Auto cell sizing— Select this option to enable APs to share information on interference seen by each other and dynamically adjust their radio Tx power and Rx parameters to minimize interference. Enabling this option, disables the TX Power Adjustment configuration.
      Note: Ensure that Background Scan is enabled.
    • TX Power Adjustment—Select the preferred TX power, if you want to manually configure the transmit power on the 5GHz radio. By default, TX power is set to Full on the 5GHz radio.
      Note: If you choose Min, the transmit power is set to 0dBm (1mW) per chain for 11n APs, and 2dBm per chain for 11ac APs. If you choose Max, the transmit power is set to the max allowable value according to the AP's capability and the operating country's regulations.
    Radio Options a/n/ac (6GHz) Indicates the configuration options for the 6GHz radio. Select the following options:
    • Channelization—Set the channel width used during transmission to either 20, 40, 80, 160 or 320 (MHz), or select Auto to set it automatically.
    • Indoor— Overrides the channel width manually for indoor operational rules.
    • Channel— For Indoor and Outdoor, select the channel to use for the a/n/c (6GHz) radio, or select Auto to set it automatically.
    • TX Power Adjustment— Select the preferred TX power, if you want to manually configure the transmit power on the 6GHz radio. By default, TX power is set to Full on the 6GHz radio.
      Note: The transmit power is set to the max allowable value according to the AP's capability and the operating country's regulations.
    • Enable Indoor AFC — Indicates the configuration options for Indoor AFC behavior.
      • Override — Select this option to manually control the AFC behavior for indoor operation. This overrides the default regulatory or controller-driven configuration.
      • Enable — Select this option to enable Automated Frequency Coordination (AFC) for the 6 GHz radio, if supported. When enabled, the AP can operate on standard-power channels based on AFC service responses.
      Note: AFC availability depends on regulatory approval and external AFC service configuration.
    Configuration > AP GRE Tunnel Options
    Tunnel Type

    Indicates the supported tunnel type (Ruckus GRE, SoftGRE and SoftGRE+IPsec)

    Choose :
    • Ruckus GRE and select the GRE Tunnel Profile.

    • SoftGRE and
      • select the GRE Tunnel Profile
      • select AAA Affinity, which is applicable only for proxy AAA.
      Note: If you select AAA Affinity, you must enable Force Disassociate Client while creating the Soft GRE Profile.
    • SoftGRE+IPsec and
      • select the GRE Tunnel Profile
      • select SoftGRE+IPsec
    Configuration > Advanced Options
    Channel Mode Indicates if location-based service is enabled. If you want to allow indoor APs that belong to this zone to use wireless channels that are Channel Mode regulated as indoor-use only. Select the Allow indoor channels check box.
    Auto Channel Selection Indicates auto-channel settings. Select the check box and choose the option.
    Background Scan Runs a background scan. Select the respective check boxes and enter the duration in seconds:
    • Background Scanning—Changes the AP channel if there is interference.
    • ChannelFly—Continuously monitors potential throughput and changes the AP channel to minimize interference and optimize throughput.
    Smart Monitor Indicates AP interval check and retry threshold settings. Select the check box and enter the interval and threshold.
    AP Ping Latency Interval Measures the latency between the controller and AP periodically, and send this data to SCI Enable by moving the radio button to ON to measure latency.
    5.1 Update - reused across platforms
    Rogue AP Detection
    Indicates rogue AP settings. Enable the option.
    5.1 Update - reused across platforms
    Rogue Classification Policy
    Indicates the parameters used to classify rogue APs. This option is available only if you enable the Rogue AP Detectionoption.

    Select the options for rogue classification policy:

      • Enable events and alarms for all rogue devices
      • Enable events and alarms for malicious rogues only
    • Report RSSI Threshold - enter the threshold. Range: 0 through 100.
    • Protect the network from malicious rogue access points - Enable the option and choose one of the following:
      • Aggressive
      • Auto
      • Conservative
    • Radio Jamming Detection - enable the option and enter the Jamming Threshold in percentage.
    DoS Protection Indicates settings for blocking a client. Select the check box and enter the duration in seconds.
    Client Load Balancing Balances the number of clients across APs. Select the check box and enter the threshold.
    Band Balancing Balances the bandwidth of the clients. You can use the slider to actively control associated stations to meet certain band distribution requirements allowing for dynamic band balancing:
    • Disable: disables band balancing
    • Basic (default): during heavy load conditions, this option withholds probe and authentication responses in order to balance clients.
    • Proactive: this is a dynamic form of band balancing where the clients are re-balanced on the AP utilizing the 802.11v BTM standard. The AP sends a BTM message to the client to change the bands and it is left to the client's discretion to make a decision on changing the bands.
    • Strict: this is an aggressive form of band balancing where the clients are forced to re-balance utilizing the 802.11v BTM standard. The AP sends a BTM message to the client to change the bands. If the client does not change the band, the client is forced to disconnect after 10 seconds.

    Note: The band change is applicable only for those connected clients that support 802.11v standard.

    Enter the percentage of client load on the 2.4 GHz band.
    Location Based Service Indicates that the location based service is enabled.
    • Select the check box and choose the options.
    • Click Create, In the Create LBS Server form:
      1. Enter the Venue Name.
      2. Enter the Server Address.
      3. Enter the Port number.
      4. Enter the Password.
    Client Admission Control Indicates the load thresholds on the AP at which it will stop accepting new clients. Select the check box and update the following settings:
    • Min Client Count
    • Max Radio Load
    • Min Client Throughput
    Protection Mode

    Indicates the mechanism to reduce frame collision.

    Choose one of the following options:
    • None
    • RTS/CTS
    • CTS Only
    AP Reboot Timeout Indicates the AP reboot settings. Choose the required option for:
    • Reboot AP if it cannot reach default gateway after
    • Reboot AP if it cannot reach the controller after
    Recovery SSID Allows you to enable or disable the Recovery(Island) SSID broadcast on the controller. Enable Recovery SSID Broadcast
  5. Click OK.

You have created the AP Zone.

Note: RUCKUS GRE over IPSec is supported in transport mode only. It provides RSA support.