Step 2c: Setup Using the Command Line Interface
The CLI setup wizard allows you to quickly configure your Unleashed Master AP with
basic settings using a short series of CLI commands.
To perform Unleashed setup using CLI commands, use the following procedure:
- When the Unleashed AP is in
factory default state, associate to the "Configure.Me-xxxxxx" WLAN and connect
to the Unleashed CLI using SSH (default IP address: 10.154.231.125), and log
in using the default user name and password: The Unleashed CLI Wizard Configuration Tool starts automatically.
- Follow the instructions in the setup wizard to configure your Unleashed Master AP.
The following are two examples.
Please login: super Password: ******** Welcome to Ruckus Wireless Unleashed CLI Setup Wizard Would you like to start the Setup Wizard? [yes/no]: yes Enter the way of installation. 1. easy-deployment installation 2. local wizard [1/2] 2 Enter Administrative User Name (32 characters max) [admin]: admin Enter Administrator Password (4-32 characters): ***** Re-enter Administrator Password (4-32 characters): ***** Enter System Name (32 characters max) [Ruckus-Unleashed]: Unleashed Enter Country Code (or 'help' to show the list) [US]: US Enable Mesh [yes/NO]? no Enable Gateway Mode [yes/NO]? no Enable Dedicated Master [yes/NO]? no Enter WAN IP type [1]: 1: DHCP Mode; 2: Manual Mode; 1 Enter Access VLAN [1]: 1 Enable WLANs [YES/no]? yes Enter Wireless LAN (ESSID, 1-32 characters) [Ruckus-Wireless 1]: Unleashed-SSID Is it an Open WLAN [yes/NO]? no Enter the WPA2 Passphrase (8-63 characters): ******** Re-enter the WPA2 Passphrase (8-63 characters): ******** Please review the following settings: System Name= Unleashed Administrator Name= admin Country Code= US Mesh Supported= Disable Gateway Mode Supported= Disable Dedicated Master Supported= Disable IPv4 Mode= DHCP Access VLAN= 1 WLAN ESSID= Unleashed-SSID Wireless Authentication= WPA2_PSK Done with the Setup Wizard [yes/no]? yes Save the configuration ... It will take a few minutes to complete, do not power off the AP! This AP will reboot automatically. Welcome to Ruckus Unleashed Network Command Line Interface ruckus>
Please login: super Password: ******** Welcome to Ruckus Wireless Unleashed CLI Command Line Interface Would you like to start the Setup Wizard? [yes/no]: yes Enter the way of installation: 1. easy-deployment installation.(Warning: The configuration costs about 15 seconds to store in system, and in flash empase the device may be damaged if power-off. So please avoid rebooting device after 60 seconds if network is reachable) 2. local wizard please enter 1 or 2: 2 Enter Administrative User Name (32 characters max) [admin]: admin Enter Administrator Password (4-32 characters): ***** Re-enter Administrator Password (4-32 characters): ***** Enter System Name (32 characters max) [Ruckus-Unleashed]: Unleashed Enter Country Code (or 'help' to show the list) [US]: US Enable Mesh [yes/NO]? yes Enable Gateway Mode [yes/NO]? Enable Dedicated Master [yes/NO]? yes Enter WAN IP type [1]: 1: DHCP Mode; 2: Manual Mode; 1 Enter Access VLAN [1]: 1 Enable WLANs [YES/no]? Enter Wireless LAN (ESSID, 1-32 characters) [Ruckus-Wireless 1]: Dedicated-SSID Is it an Open WLAN [yes/NO]? Enter the WPA2 Passphrase (8-63 characters): ******** Re-enter the WPA2 Passphrase (8-63 characters): ******** Please review the following settings: System Name= Unleashed Administrator Name= admin Country Code= US Mesh Supported= Enable Gateway Mode Supported= Disable Dedicated Master Supported= Enable IPv4 Mode= DHCP Access VLAN= 1 WLAN ESSID= Dedicated-SSID Wireless Authentication= WPA2_PSK Done with the Setup Wizard [yes/no]? yes Save the configuration ... It will take a few minutes to complete, do not power off the AP! This AP will reboot automatically. Welcome to Ruckus Unleashed Network Command Line Interface ruckus>
Please login: super Password: ******** Welcome to Ruckus Wireless Unleashed CLI Setup Wizard Would you like to start the Setup Wizard? [yes/no]: yes Enter the way of installation. 1. easy-deployment installation 2. local wizard [1/2] 2 Enter Administrative User Name (32 characters max) [admin]: admin Enter Administrator Password (4-32 characters): ***** Re-enter Administrator Password (4-32 characters): ***** Enter System Name (32 characters max) [Ruckus-Unleashed]: Unleashed-Gateway Enter Country Code (or 'help' to show the list) [US]: US Enable Mesh [yes/NO]? no Enable Gateway Mode [yes/NO]? yes Enter AP R510 WAN Port: 1: port1, eth0, UP: 2: port2, eth1, DOWN: 1 Enter WAN IP type [1]: 1: DHCP Mode; 2: Manual Mode; 3: PPPOE Mode; 1 Enter LAN & WLAN IP Address [10.106.0.1]: 192.168.1.1 Enter LAN & WLAN IP Netmask [255.255.0.0]: 255.255.255.0 Enter Client Starting IP Address [10.106.0.2]: 192.168.1.2 Enter Client Ending IP Address [10.106.7.209]: 192.168.1.200 Enter Lease Time [2]: 1: 6 hours; 2: 12 hours; 3: 1 day; 4: 2 days; 5: 1 week; 6: 2 weeks; 1 Enable WLANs [YES/no]? yes Enter Wireless LAN (ESSID, 1-32 characters) [Ruckus-Wireless 1]: Unleashed-SSID Is it an Open WLAN [yes/NO]? no Enter the WPA2 Passphrase (8-63 characters): ******** Re-enter the WPA2 Passphrase (8-63 characters): ******** Please review the following settings: System Name= Unleashed-Gateway Administrator Name= admin Country Code= US Mesh Supported= Disable Gateway Mode Supported= Enable WAN Port= port1 eth0 UP IPv4 Mode= DHCP LAN Port IPv4 Address Info= 192.168.1.1/255.255.255.0 Client Starting IPv4= 192.168.1.2 Client Ending IPv4= 192.168.1.200 Lease Time= 6 hours WLAN ESSID= Unleashed-SSID Wireless Authentication= WPA2_PSK Done with the Setup Wizard [yes/no]? yes Save the configuration ... It will take a few minutes to complete, do not power off the AP! This AP will reboot automatically. Welcome to Ruckus Unleashed Network Command Line Interface ruckus>