R610

The R610 is the first Ruckus three stream (3x3:3) Wave 2 802.11ac dual-band concurrent indoor Access Point.

Note: The R610 AP requires a minimum of AP base image 104.1 and later to operate, or SmartZone 3.4 and later, or ZoneDirector 9.13.2 and later to operate.

The R610 expands Ruckus' portfolio of 11ac Wave 2 APs, providing all of the benefits of Wave 2 along with an extensive list of features such as dual gigabit ports with Link Aggregation, USB port for IoT devices, and flexible power options including 12VDC, 802.3at and 802.3af PoE/ PoE+ support.

Note: Note that if 802.3af PoE is used to power the R610, the feature set is reduced, as follows:
  • 2.4 GHz radio chains reduced to 2x3 (2-chain transmit at 21dBm aggregate power, 3-chain receive)
  • USB port disabled
  • 2nd Ethernet port disabled

The R610 includes five LEDs on its front panel and buttons and connectors on its rear panel.

Front View Features

The following figure shows the top view of the R610. For a description of the front panel LEDs, refer to the table below.

R610 top view

R610 front panel LEDs

LED Description
PWR
  • Off: Off.
  • Red: Boot up in process.
  • Flashing Green: No routable IP address
  • Green: On.
CTL
  • Off: The AP is not being managed by a controller (standalone mode).
  • Green: The AP is being managed by a controller.
  • Slow flashing green (one flash every two seconds): The AP is being managed by a controller, but is currently unable to communicate with the controller.
  • Fast flashing green (two flashes every second): The AP is being managed by a controller and is currently receiving configuration settings (provisioning) or an image update.
AIR
  • Off: The AP is operating in standalone mode or operating as a root AP (RAP) or a non-mesh AP.
  • Green: The AP is functioning as a Mesh AP (MAP), and the wireless signal to its uplink AP is good.
  • Fast flashing green (two flashes every second): The AP is functioning as a Mesh AP (MAP), and the wireless signal to its uplink AP is fair.
  • Slow flashing green (one flash every two seconds): Mesh networking is enabled, but the AP is still searching for a mesh uplink.
2.4G
  • Off: The WLAN service is down.
  • Green: The WLAN is up and at least one client is associated.
  • Amber: The WLAN is up. No clients are associated.
5G
  • Off: The WLAN service is down.
  • Amber: The WLAN is up, but no clients or downlink MAPs are associated/connected.
  • Green: The WLAN is up and at least one client is associated. No downlink MAPs are connected.
  • Slow flashing green (one flash every two seconds): The WLAN is up and at least one downlink MAP is connected. No clients are associated.
  • Fast flashing green (two flashes every second): The WLAN is up, at least one downlink MAP is connected, and at least one client is associated.

Rear Panel

The rear panel of the R610 includes two 10/100/1000 Ethernet ports, one of which supports PoE, power socket and reset button. See the table below for a description of each rear panel part.

R610 rear panel

R610 Rear panel element descriptions

Label Description
RESET Button Pressing, and then quickly releasing this button reboots the AP. Pressing and holding it for six seconds resets the AP to factory default settings.
Note: Resetting the AP to factory default settings erases all settings that you configured previously.
PoE Port One RJ-45 port for a 10/100/1000 PoE (Power over Ethernet, 802.3af/at) connection.
Ethernet Port One RJ-45 port for a 10/100/1000 connection.
12VDC Connect the power adapter (12 VDC/1.25A) to this socket. Power can also be supplied via the 10/100/1000 PoE port.

Ethernet Port LEDs

Behavior of Ethernet port LEDs on the R610

LED Description
Off Not connected
Amber + Green Connected to 10Mbps device
Amber Connected to 100Mbps device
Green Connected to 1000Mbps device

R610 Power Modes

The following table lists the R610's power modes and the corresponding feature set under the different power modes. When both power sources are available on an AP, then DC power will take priority and override PoE power. When the AP is connected to a PoE switch the max power requested by the AP is captured in the second column, and rest of the columns describe the operational capability for each mode.

Note: The dBm transmit power values below are per chain.

R610 Power Modes

PoE Mode

Power Level

5 GHz Radio

2.4 GHz Radio

1G Eth (PoE) Port

1G Eth Port

USB

160/ 80+80

DC Full Power 3 x 3

20 dBm

3 x 3

22 dBm

Enabled Enabled Enabled Yes 1 x 1
802.3af 12.95 W 3 x 3

20 dBm

2 x 3

18 dBm

Enabled Disabled Disabled Yes 1 x 1
802.3at/ injector 25.0 W 3 x 3

20 dBm

3 x 3

22 dBm

Enabled Enabled Enabled Yes 1 x 1