R500

The Ruckus R500 is a high-performance 2x2:2 802.11ac dual-band AP designed for medium client density deployments.
Note: The R500 AP requires a minimum of standalone AP base image 100.0.0 and later to operate, or SCG 2.5.1 and later, vSZ 3.0 and later, SmartZone software 3.2 and later, or ZD 9.8.1 and later to operate.

The R500 includes five LEDs on its front panel and buttons and connectors on its rear panel.

Front View Features

The following figure shows the top view of the R500. For a description of the front panel LEDs, refer to the table below.

R500 top view

R500 front panel LEDs

LED Description
PWR
  • Off: Off.
  • Red: Boot up in process.
  • Flashing Green: No routable IP address
  • Green: On.
DIR
  • Off: The AP is not being managed by a controller (standalone mode).
  • Green: The AP is being managed by a controller.
  • Slow flashing green (one flash every two seconds): The AP is being managed by a controller, but is currently unable to communicate with the controller.
  • Fast flashing green (two flashes every second): The AP is being managed by a controller and is currently receiving configuration settings (provisioning) or an image update.
AIR
  • Off: The AP is operating in standalone mode or operating as a root AP (RAP) or a non-mesh AP.
  • Green: The AP is functioning as a Mesh AP (MAP), and the wireless signal to its uplink AP is good.
  • Fast flashing green (two flashes every second): The AP is functioning as a Mesh AP (MAP), and the wireless signal to its uplink AP is fair.
  • Slow flashing green (one flash every two seconds): Mesh networking is enabled, but the AP is still searching for a mesh uplink.
2.4G
  • Off: The WLAN service is down.
  • Green: The WLAN is up and at least one client is associated.
  • Amber: The WLAN is up. No clients are associated.
5G
  • Off: The WLAN service is down.
  • Amber: The WLAN is up, but no clients or downlink MAPs are associated/connected.
  • Green: The WLAN is up and at least one client is associated. No downlink MAPs are connected.
  • Slow flashing green (one flash every two seconds): The WLAN is up and at least one downlink MAP is connected. No clients are associated.
  • Fast flashing green (two flashes every second): The WLAN is up, at least one downlink MAP is connected, and at least one client is associated.

Rear Panel

The rear panel of the R500 includes one 10/100/1000 Mbps PoE Ethernet port, one 10/100/1000 Mbps (non-PoE) Ethernet port, power socket and reset button. See the table below for a description of each rear panel part.

R500 rear panel

R500 Rear panel element descriptions

Label Description
RESET Button Pressing, and then quickly releasing this button reboots the AP. Pressing and holding it for six seconds resets the AP to factory default settings.
Note: Resetting the AP to factory default settings erases all settings that you configured previously.
PoE Port One RJ-45 port for a 10/100/1000 PoE (Power over Ethernet, 802.3af/at) connection. (The R500 is a Class 3 device.)
Ethernet Port One RJ-45 port for a 10/100/1000 connection.
12VDC Connect the power adapter (12 VDC/1.25A) to this socket. Power can also be supplied via the 10/100/1000 PoE port.

Ethernet Port LEDs

Behavior of Ethernet port LEDs on the R500

LED Description
Off Not connected
Amber + Green Connected to 10Mbps device
Amber Connected to 100Mbps device
Green Connected to 1000Mbps device
Warning: For units using Power over Ethernet (PoE). These products and all interconnected equipment must be installed indoors within the same building, including the associated LAN connections, as defined by Environment A of the IEEE 802.3af Standard.