Ruckus Indoor Access Point Release 110.0 User Guide
- 3 About This Guide
- 3.1 Before You Begin
- 3.2 Safety Warnings
- 3.3 Related Documentation
- About This Guide
- 5 Installation
- 5.1 Before You Begin
- 5.2 Step 1: Preconfiguring the AP
- 5.2.1 Configuring the AP for Management by a SmartZone Controller
- 5.2.2 Configuring the AP for Management by ZoneDirector
- 5.2.3 Configuring the AP for Standalone Operation
- 5.2.3.1 Collect the Required Materials
- 5.2.3.2 Prepare the Administrative Computer
- 5.2.3.3 Connect the AP to the Administrative Computer
- 5.2.3.4 Log Into the AP's Web Interface
- 5.2.3.5 Configure the Common Wireless Settings
- 5.2.3.6 Configuring Wireless # (WLAN number) Settings
- 5.2.3.7 Disconnecting the AP from the Administrative Computer
- 5.2.3.8 Restoring the Administrative Computer's Network Settings (Optional)
- 5.3 Step 2: Verifying AP Operation
- 5.4 Step 3: Deploying the AP
- 5.5 Troubleshooting the Installation
- 6 Navigation
- 7 Configuration
- 7.1 Configuring the AP
- 7.1.1 Configuring Device Settings
- 7.1.2 Configuring Internet Settings
- 7.1.2.1 VLAN Settings Overview
- 7.1.2.2 Configuring NTP Server and Management VLAN
- 7.1.2.3 Default IP Addressing Behavior
- 7.1.2.4 Obtaining and Assigning an IP Address
- 7.1.2.4.1 DHCP / Auto Configuration
- 7.1.2.4.1.1 Renewing and Releasing DHCP
- 7.1.2.4.2 Configuring Static IP
- 7.1.2.4.2.1 Static IPv4
- 7.1.2.4.2.2 Static IPv6
- 7.1.2.4.3 Configuring PPPoE
- 7.1.2.4.1 DHCP / Auto Configuration
- 7.1.2.5 Configuring L2TP Connection Settings
- 7.1.2.6 Configuring Local Subnets
- 7.1.3 Configuring Wireless Settings
- 7.1.3.1 Configuring Common Wireless Settings
- 7.1.3.1.1 Configuring Common Advanced Settings
- 7.1.3.2 Configuring Wireless # (WLAN Number) Settings
- 7.1.3.3 Using WEP
- 7.1.3.4 Using WPA
- 7.1.3.5 Customizing 802.1X Settings
- 7.1.3.6 Setting Threshold Options
- 7.1.3.7 Rate Limiting
- 7.1.3.8 Controlling Access to the Wireless Network
- 7.1.3.8.1 Access Control Options
- 7.1.3.8.2 Changing the Access Controls for a WLAN
- 7.1.3.8.2.1 Removing a MAC Address
- 7.1.3.1 Configuring Common Wireless Settings
- 7.1.4 Configuring Ethernet Ports
- 7.1.4.1 Setting Ethernet Port Type
- 7.1.4.2 Working with Port-Based VLANs
- 7.1.4.3 Working with 802.1X on Wired Ethernet Ports
- 7.1.5 Configuring Hotspot Service
- 7.1.5.1 Customizing Hotspot Optional Settings
- 7.1.5.2 Creating a Hotspot Walled Garden
- 7.1.5.2.1 Creating Walled Garden Rules
- 7.1.5.2.2 Removing entries from the Walled Garden hosts table
- 7.1.5.2.3 Allowing Unrestricted Access by MAC Address
- 7.1 Configuring the AP
- Administration
- 8 Administration
- 8.1 Administration
- 8.2 Viewing Current Device Settings
- 8.3 Viewing Current Internet Connection Settings
- 8.4 Viewing Current Local Subnet Settings
- 8.5 Viewing FlexMaster Management Status
- 8.6 Viewing Associated Wireless Clients
- 8.7 Viewing Common Wireless Settings
- 8.8 Changing the Administrative Login Settings
- 8.9 Enabling Other Management Access Options
- 8.10 Working with Event Logs and Syslog Servers
- 8.11 Pointing the AP to FlexMaster
- 8.12 Upgrading the Firmware Image
- 8.13 Rebooting the AP
- 8.14 Resetting the AP to Factory Defaults
- 8.15 Running Diagnostics
- 8.16 Where to Find More Information
- 9 AP Support for Bluetooth Low Energy Devices
- 10 Configuring Link Aggregation (LACP) for AP Backhaul
- 8 Administration