Managing Access Points Individually

You can add a description, or change the channel selection, transmit power and Ethernet port settings of a managed access point by editing the AP's parameters. Additionally, you can manually assign an IP address or disable WLAN service entirely for a specific radio.

Configuring any of these settings for an individual AP overrides the settings configured in AP Groups.

To edit the parameters of an access point:

  1. Go to Access Points.
  2. Select the AP you want to edit from the Access Points table, and then click the Configure button.
  3. In the Edit AP form, edit any of the following General settings:
    • Device Name: Enter a descriptive name for the AP for easy identification in ZoneDirector tables and Dashboard widgets. Names can consist of up to 64 letters, numbers, hyphens and underscores. Note however that only the first 17 characters of the device name will be displayed in the Events/Activities tables.
    • Description: Enter a description for the AP. This description is used to identify the AP in the Map View.
    • Location: Enter a recognizable location for the AP.
    • GPS Coordinates: Enter GPS coordinates for AP location on the Google/Bing Maps on the Dashboard.
    • Group: Select an AP group from the list if you want to place this AP into a group other than the system default group.
    • Bonjour Gateway: Designate this AP as a AP-side Bonjour Gateway. See Creating a Bonjour Gateway Rule AP Site.
    • Bonjour Fencing: Implement on Bonjour Fencing Policy on this AP. See Bonjour Fencing.
  4. In Channel Range Settings, you can manually configure available channels. Click Override Group Config and change the default values, the following parameters can be configured independently for each AP radio:
    • Channel Range Settings: Deselect any channels that you do not want the AP to use in channel selection.
      Note: For country codes "US" and "JP", channel 144 is supported if DFS channel is enabled.
  5. In Radio B/G/N/AX (2.4 GHz), and Radio A/N/AC/AX (5 GHz), override the AP group configuration and configure the following settings:
    • Channelization: Sets the channel width of each channel in the spectrum used during transmission.
    • Channel: Manually set the channel used by the AP radio.
    • Tx Power: Manually set the maximum transmit power level relative to the calibrated power.

      Max = max allowable Tx power according to country regulations

      Min = 0dBm per chain for 11n APs, 2dBm per chain for 11ac APs

    • WLAN Group: Specify a WLAN group for this radio.
    • Call Admission Control: (Disabled by default). Enable Wi-Fi Multimedia Admission Control (WMM-AC) to support Polycom/Spectralink VIEW certification. See Advanced WLAN Options under Creating a WLAN for more information.
    • WLAN Service: Uncheck this check box to disable WLAN service entirely for this radio. (This option can be useful if you want dual-band 802.11n/ac APs to provide service only on the 5 GHz radio, in order to reduce interference on the 2.4 GHz band, for example.) You can also disable service for a particular WLAN at specific times of day or days of the week, by setting the Service Schedule. For more information, see Advanced WLAN Options for creating a WLAN.
    • External Antenna: On APs with external antenna options, select Override System Default, and Enable for the external antenna to be enabled. Once enabled, enter a gain value in the range of 0 to 90dBi.
    • Protection Mode: (2.4 GHz radio only) Configure advanced RF settings as follows:
      • CTS Only: Choose this option to force all destination devices to acknowledge their ability to receive data when a transmission is initiated. Use this option for compliance with the Wi-Fi Alliance certification.
      • RTS/CTS: Choose this option to force both sending and receiving devices to confirm a data exchange on both ends before proceeding.
      • None: Choose this option to disable both RTS and CTS acknowledgment.
  6. The Network Setting options allow you to configure the IP address settings of the AP:
    • IP Mode: Select IPv4 only, IPv6 only or dual IPv4/IPv6 addressing mode. If you want the AP to keep its current IP address, click Keep AP's Setting. If the AP's IP address has not been set, it will automatically attempt to obtain an IP address via DHCP.
    • If you want the AP to automatically obtain its IP address settings from a DHCP server on the network, click the DHCP option in Management IP. You do not need to configure the other settings (netmask, gateway, and DNS servers).
    • If you want to assign a static IP address to the AP, click the Manual option next to Device IP Settings, and then set the values for the following options:
      • IP Address
      • Netmask
      • Gateway
      • Primary DNS Server
      • Secondary DNS Server
  7. If Smart Mesh is enabled (see Deploying a Smart Mesh Network), the Mesh Settings section lets you define the role this AP should play in the mesh network--Auto, Root AP, Mesh AP, or Disable (default is Auto). In most cases, RUCKUS recommends leaving this setting on Auto to reduce the risk of isolating a Mesh AP. Select Disable if you do not want this AP to be part of your mesh network.
  8. If this AP is a Mesh AP and you want to manually set which APs can serve as its uplinks, select the Manual radio button under Advanced Options > Uplink Selection (default is Smart). The other APs in the mesh appear below the selection.
  9. Select the check box next to each AP that you want to allow the current AP to use as an uplink. If you set Uplink Selection for an AP to Manual and the uplink AP that you selected is off or unavailable, the AP status on the Access Points page will appear as Isolated Mesh AP. See Troubleshooting Isolated Mesh APs for more information.
  10. In Model Specific Control, override the AP group configuration and configure the following options for this AP (for information on these settings, see Working with Access Point Groups:
    • PoE Operating Mode: Choose Auto (default), 802.3af, 802.3at, or 802.3at+ PoE operating mode.
    • USB Port: Disable the USB port on this AP.
    • Status LEDs: Disable the status LEDs on this AP.
    • LACP/LAG: Enable Link Aggregation Control Protocol (LACP) on this AP.
    • Port Setting: Configure AP Ethernet port settings. See the following step.
  11. If you select Override Group Config in the Port Setting section, a new section opens where you can customize the Ethernet port behavior for this AP. Enabling this will override the AP Group settings made on Configuring AP Ethernet Ports.
  12. Click OK to save your changes.