Control Plane configuration includes defining the physical interface, user defined
interface and static routes.
To configure a control plane:
Go to Network > Data and Control
Plane > Cluster.
Select the control plane from the list and click
Configure. The Edit Control Plane Network Settings form appears.
Configure the settings as explained in the table below.
Click OK.
Note: You must configure the Control interface, IPv4 Cluster
interface, and Management interface to be on three different subnets. Failure to
do so may result in loss of access to the web interface or failure of system
functions and services.
Configuring Control
Plane
Field
Description
Your Action
Physical
Interfaces
IPv4-Control Interface
Indicates the management and IP control
settings.
Select the IP
Mode:
Static (recommended)—To manually assign an IP address
to this interface manually.
Enter the IP
Address.
Enter Subnet Mask.
Enter the Gateway router address.
Enter Control NAT IP address.
DHCP—To automatically obtain an IP address
from a DHCP server on the network.
Enter Control NAT IP.
IPv4-Cluster Interface
Indicates the IPv4 cluster interface
settings
Select the IP
Mode:
Static (recommended)—To manually assign an IP address
to this interface manually.
Enter the IP
Address.
Enter Subnet Mask.
Enter the Gateway router address.
DHCP—To automatically obtain an IP address
from a DHCP server on the network.
IPv4-Management Interface
Indicates the IPv4 management interface
settings
Select the IP
Mode:
Static (recommended)—To manually assign an IP address
to this interface manually.
Enter the IP
Address.
Enter Subnet Mask.
Enter the Gateway router address.
DHCP—To automatically obtain an IP address
from a DHCP server on the network.
IPv6-Control Interface
Indicates the IPv6 control interface
settings
Select the IP
Mode:
Static (recommended)—To manually assign an IP address
to this interface manually.
Enter the IPv6 IP
Address (global only) with a prefix length
(for example, 1234::5678:0:C12/123) is required.
Link-local addresses are unsupported.
Enter the IPv6 Gateway address (global or link-local)
without a prefix length. For example,
1234::5678:0:C12 (global address without a prefix
length) and fe80::5678:0:C12 (link-local address
without a prefix length).
Auto—To automatically obtain an IP address
from Router Advertisements (RAs) or from a DHCPv6
server on the network.
IPv6-Management Interface
Indicates the IPv6 management interface
settings
Select the IP
Mode:
Static (recommended)—To manually assign an IP address
to this interface manually.
Enter the IPv6 IP
Address (global only) with a prefix length
(for example, 1234::5678:0:C12/123) is required.
Link-local addresses are unsupported.
Enter the IPv6 Gateway address (global or link-local)
without a prefix length. For example,
1234::5678:0:C12 (global address without a prefix
length) and fe80::5678:0:C12 (link-local address
without a prefix length).
Auto—To automatically obtain an IP address
from Router Advertisements (RAs) or from a DHCPv6
server on the network.
Access
& Core Separation
Indicates that the management interface (core
side) to be the system default gateway and the control
interface (access side) to be used only for access traffic.
Select the Enable check box.
IPv4
Default Gateway & DNS
Indicates the IPv4 gateway that you want to
use - Control, Cluster, and Management.
Note: When Access & Core Separation is enabled, the Default Gateway field is hidden.
Note: The
default gateway is NOT set to Control Interface. To
properly route AP/UE traffic back through Control
Interface, please make sure to enable Access & Core
Separation or add static routes in Control Plane Network
Settings on Web GUI.
Default Gateway—Choose the Interface for
which you want to assign the default gateway
setting.
Primary DNS Server—Enter the server details.
Secondary DNS Server—Enter the server
details.
IPv6
Default Gateway & DNS
Indicates the IPv6 gateway that you want to
use - Control, Cluster, and Management.
Note: When Access & Core Separation is enabled, the Default Gateway field is hidden.
Note: The
default gateway is NOT set to Control Interface. To
properly route AP/UE traffic back through Control
Interface, please make sure to enable Access & Core
Separation or add static routes in Control Plane Network
Settings on Web GUI.
Default Gateway—Choose the Interface for
which you want to assign the default gateway
setting.
Primary DNS Server—Enter the server details.
Secondary DNS Server—Enter the server
details.
User
Defined Interfaces
Note: The
control plane and the UDI must be on different subnets.
If the control plane and UDI are on the same subnet, and
assigned the same IP address, APs will be unable to
communicate with the control plane. If the control plane
and UDI are on the same subnet and assigned different IP
addresses, hotspot clients will not be redirected to the
logon URL for user authentication.
Name
Indicates the name of the interface.
Enter a name.
Physical
Interfaces
Indicates the physical interface.
Select Control
Interface.
Service
Indicates the service.
Select Hotspot, the hotspot must uses the control
interface as its physical interface.
IP
Address
Indicates the IP address that you want to
assign to this interface.
Enter the IP address.
Subnet
Mask
Indicates the subnet mask for the IP
address.
Enter the subnet mask.
Gateway
Indicates the IP address of the gateway
router.
Enter the gateway IP address.
VLAN
Indicates the VLAN ID that you want to assign
to this interface.
Enter the VLAN ID.
Add
Adds the interface settings.
Click Add.
Static
Routes
Network
Address
Indicates the destination IP address of this
route.
Enter the IP address.
Subnet
Mask
Indicates a subnet mask for the IP address.
Enter the subnet mask.
Gateway
Indicates the IP address of the gateway
router.
Enter the IP address of the gateway router.
Interface
Indicates the physical interface to use for
this route.
Select the interface.
Metric
Represents the number of routers between the
network and the destination.
Enter the number of routers.
Add
Adds the static route settings.
Click Add.
Note: You can also delete or restart a control plane. To do so, select the control plane
from the list and click
Delete or
Restart respectively.