setup
Sets up the controller network interface settings.
Modes
Privileged EXEC mode
Usage Guidelines
Use the command to help you configure the network interface settings using prompts.
This command is supported on all SmartZone platforms except SmartZone Data Plane controller.
Examples
The following example walks you through prompts to help you set up a SZ300 controller.
ruckus# setup ################################################ Start controller setup process: ################################################ Network is not setup. ************************************************ IP Version Support ************************************************ 1. IPv4 only 2. IPv4 and IPv6 ************************************************ Select address type: (1/2) 2 ************************************************ IPv4 address setup for Control interface ************************************************ 1. Manual 2. DHCP ************************************************ Select IP configuration: (1/2) 2 ************************************************ IPv4 address setup for Cluster interface ************************************************ 1. Manual 2. DHCP ************************************************ Select IP configuration: (1/2) 2 ************************************************ IPv4 address setup for Management interface ************************************************ 1. Manual 2. DHCP ************************************************ Select IP configuration: (1/2) 2 ************************************************ Default Gateway Interface ************************************************ 1. Control 2. Cluster 3. Management ************************************************ Select gateway interface: (1/2/3) 3 Primary DNS: 172.17.17.16 Secondary DNS: ************************************************ IPv6 address setup for Control interface ************************************************ 1. Manual 2. DHCPv6 ************************************************ Select IPv6 configuration: (1/2) 2 ************************************************ IPv6 address setup for Management interface ************************************************ 1. Manual 2. DHCPv6 ************************************************ Select IPv6 configuration: (1/2) 2 ************************************************ IPv6 Default Gateway Interface ************************************************ 1. Control 2. Management ************************************************ Select IPv6 gateway interface: (1/2) 1 Primary IPv6 DNS: Secondary IPv6 DNS: ************************************************ Current Network Settings (Before Applying) ************************************************ ************************************************ IP Version Support Settings: ************************************************ IP Version Support : IPv4 and IPv6 Interface IPv4 settings: ************************************************ Control: ************************************************ IP Type : DHCP IP Address : 192.168.2.53 Netmask : 255.255.255.0 Gateway : 192.168.2.219 ************************************************ Cluster: ************************************************ IP Type : DHCP IP Address : 192.168.100.88 Netmask : 255.255.255.0 Gateway : ************************************************ Management: ************************************************ IP Type : DHCP IP Address : 172.17.25.55 Netmask : 255.255.255.0 Gateway : Default Gateway : yes ************************************************ DNS Server Settings: ************************************************ Primary DNS Server : 172.17.17.16 Secondary DNS Server : Interface IPv6 settings: ************************************************ Control: ************************************************ IP Type : DHCPv6 IP Address : Gateway Type : RA Gateway : Default Gateway : yes ************************************************ Management: ************************************************ IP Type : DHCPv6 IP Address : Gateway Type : RA Gateway : ************************************************ DNS Server Settings: ************************************************ Primary DNS Server : Secondary DNS Server : ************************************************ Enter 'y' to apply, 'n' to modify Do you want to apply the settings? (y/n) Please wait while sytem configures the network. It may take a few minutes... ************************************************ Current Network Settings (After Applying) ************************************************ ************************************************ IP Version Support Settings: ************************************************ IP Version Support : IPv4 and IPv6 Interface IPv4 settings: ************************************************ Control: ************************************************ IP Type : DHCP IP Address : 192.168.2.53 Netmask : 255.255.255.0 Gateway : ************************************************ Cluster: ************************************************ IP Type : DHCP IP Address : 192.168.100.88 Netmask : 255.255.255.0 Gateway : ************************************************ Management: ************************************************ IP Type : DHCP IP Address : 172.17.25.55 Netmask : 255.255.255.0 Gateway : 172.17.25.1 Default Gateway : yes ************************************************ DNS Server Settings: ************************************************ Primary DNS Server : 172.17.17.16 Secondary DNS Server : Interface IPv6 settings: ************************************************ Control: ************************************************ IP Type : DHCPv6 IP Address : fccc:192:168:2::eba/128 Gateway Type : RA Gateway : fe80::20c:29ff:fef9:7e85 Default Gateway : yes ************************************************ Management: ************************************************ IP Type : DHCPv6 IP Address : fccc:172:17:25::705/128 Gateway Type : RA Gateway : fe80::20c:29ff:fef9:7e85 ************************************************ DNS Server Settings: ************************************************ Primary DNS Server : Secondary DNS Server : ************************************************ Enter 'y' to accept, 'n' to modify Accept these settings and continue? (y/n) y SZ300# setup ################################################ Start SZ300 setup process: ################################################ Current Network Settings ************************************************ IP Version Support Settings: ************************************************ IP Version Support : IPv4 and IPv6 Interface IPv4 settings: ************************************************ Control: ************************************************ IP Type : DHCP IP Address : 192.168.2.53 Netmask : 255.255.255.0 Gateway : ************************************************ Cluster: ************************************************ IP Type : DHCP IP Address : 192.168.100.88 Netmask : 255.255.255.0 Gateway : ************************************************ Management: ************************************************ IP Type : DHCP IP Address : 172.17.25.55 Netmask : 255.255.255.0 Gateway : 172.17.25.1 Default Gateway : yes ************************************************ DNS Server Settings: ************************************************ Primary DNS Server : 172.17.17.16 Secondary DNS Server : Interface IPv6 settings: ************************************************ Control: ************************************************ IP Type : DHCPv6 IP Address : fccc:192:168:2::eba/128 Gateway Type : RA Gateway : fe80::20c:29ff:fef9:7e85 Default Gateway : yes ************************************************ Management: ************************************************ IP Type : DHCPv6 IP Address : fccc:172:17:25::705/128 Gateway Type : RA Gateway : fe80::20c:29ff:fef9:7e85 ************************************************ DNS Server Settings: ************************************************ Primary DNS Server : Secondary DNS Server : ************************************************ Do you want to setup network? (y/n) n (C)reate a new cluster or (J)oin an exist cluster (c/j): c Cluster Name (cluster name can contain letters (a-z, A-Z), numbers (0-9), and dashes (-)): ruckus-cluster-1 Controller Description: ruckus controller ************************************************ Create/Join : create DISCOVERY PROTOCOL: tcp Cluster Name : ruckus-cluster-1 Blade ID : 83405b79-9286-4b57-8701-c7ecddf27c40 DESCRIPTION : ruckus controller ************************************************ Are these correct (y/n): y Enter the controller name of the blade ([a-zA-Z0-9-]): ruckus-controller Is this controller behind NAT? (y/n) n System UTC Time: 2020-02-06 07:39:53 UTC NTP Server ([a-zA-Z0-9.-]): [ntp.ruckuswireless.com] Check if NTP server [ntp.ruckuswireless.com] is reachable... System time after synchronization: 2020-02-06 07:40:01 UTC Convert ZoneDirector APs in factory settings to SZ300 APs automatically (y/n) [N] Reset admin's password! Enter admin password: Enter admin password again: Enter the CLI enable command password: Enter the CLI enable command password again: Reset admin's password done! Setup configurations done. Starting setup process after 5 seconds... /etc/init.d/snmpd restart New hostname: ruckus-controller Change admin password done! ************************************************ Check installation status ************************************************ Wait for cluster config operation start! Wait for cluster config operation start! Wait for cluster config operation start! Wait for cluster config operation start! Bootstrapping, Tue Feb 06 07:40:33 UTC 2020 Blade Channel Opened, Tue Feb 06 07:40:36 UTC 2020 Configurer Channel Opened, Tue Feb 06 07:40:46 UTC 2020 Cassandra Started, Tue Feb 06 07:41:59 UTC 2020 ElasticSearch Started, Tue Feb 06 07:43:08 UTC 2020 Cassandra Initialized, Tue Feb 06 07:47:31 UTC 2020 Certificate and Root Key created, Tue Feb 06 07:49:02 UTC 2020 SZ300 Apps Started, Tue Feb 06 08:03:58 UTC 2020 Available, Tue Feb 06 08:04:13 UTC 2020 [##################################################]100% % System setup is finished. The current CLI session will be terminated. Please login again.
ruckus# setup ################################################ Start SCG setup process: ################################################ Current network settings: ************************************ Control(AP/Dataplane): ************************************ IP TYPE : dhcp IP Address : 10.2.6.231 Netmask : 255.255.0.0 Gateway : 10.2.0.1 Default Gateway : no Primary DNS Server : 172.17.17.16 Secondary DNS Server : 168.95.1.1 ************************************ ************************************ Cluster: ************************************ IP TYPE : dhcp IP Address : 10.2.6.229 Netmask : 255.255.0.0 Gateway : 10.2.0.1 Default Gateway : no Primary DNS Server : 172.17.17.16 Secondary DNS Server : 168.95.1.1 ************************************ ************************************ Management(Web): ************************************ IP TYPE : dhcp IP Address : 10.2.6.230 Netmask : 255.255.0.0 Gateway : 10.2.0.1 Default Gateway : yes Primary DNS Server : 172.17.17.16 Secondary DNS Server : 168.95.1.1 ************************************ Server need to restart network after network setting. Do you want to setup network? [YES/no]: no (C)reate a new cluster or (J)oin an exist cluster: (c/j) c Cluster Name ([a-zA-Z0-9_-]): test_cluster Controller Description: test_cluster ************************************ Create/Join : create DISCOVERY PROTOCOL: tcp Cluster Name : test_cluster Blade ID : f7585769-6dd7-4e63-aa2c-e6da76501680 DESCRIPTION : test_cluster ************************************ Are these correct? (y/n): y Enter the controller name of the blade([a-zA-Z0-9_-]): test_cluster NTP Server ([a-zA-Z0-9._-]): [pool.ntp.org] Reset admin's password! Enter admin password: Enter admin password again: Enter the enable password: Enter the enable password again: Reset admin's password done! stty: standard input: Invalid argument New hostname: test_cluster Change admin password done! ************************************ Check SCG installation status ************************************ Wait for cluster config operation start! Wait for cluster config operation start! Wait for cluster config operation start! Wait for cluster config operation start! Bootstrapping, Tue Dec 18 15:25:32 GMT 2012 Blade Channel Jointed, Tue Dec 18 15:25:34 GMT 2012 Configurer Channel Jointed, Tue Dec 18 15:25:43 GMT 2012 Cassandra Started, Tue Dec 18 15:26:03 GMT 2012 Cassandra Initialized, Tue Dec 18 15:27:14 GMT 2012 First Time Initialization Process Done, Tue Dec 18 15:28:02 GMT 2012 Available, Tue Dec 18 15:29:47 GMT 2012