| ruckusWiredClientsTable snSwitch.43.1.1.1
|
Not-accessible
|
RUCKUS wired client table.
|
| ruckusWiredClientEntry snSwitch.43.1.1.1.1
|
Not-accessible
|
An entry containing information about a specific client on a given port.
|
| ruckusWiredClientMac snSwitch.43.1.1.1.1.1
Syntax:
Mac-address
|
Read-only
|
Specifies the MAC address of the client (device/host) represented by this client entry.
|
| ruckusWiredClientVlan snSwitch.43.1.1.1.1.2
Syntax: VLAN
ID
|
Read-only
|
Specifies the VLAN that the client (device/host) belongs to, represented by this client
entry.
In case of voice-phones, this VLAN is the voice-VLAN (tagged) and in all other cases,
it would be an untagged VLAN, unless it is a tagged VM client.
|
| ruckusWiredClientType snSwitch.43.1.1.1.1.3
Syntax:
Integer
|
Read-only
|
Describes the type of the client connected on this port.
|
| ruckusWiredClientAuthType snSwitch.43.1.1.1.1.4
Syntax:
Integer
|
Read-only
|
Specifies the authentication method that is used for authenticating the client on
this port, represented by this client (when FlexAuth is enabled), else it is none.
|
| ruckusWiredClientStatus snSwitch.43.1.1.1.1.5
Syntax:
Integer
|
Read-only
|
The authentication state of the client which can take the following values.
noAuth(1) - not authenticated
allowed(2) - client authentication is successful, so the complete access is granted.
blocked(3) - client failed authentication, so access is denied.
restrict(4)- client failed authentication, but allowed restricted access.
critical(5) - client authentication time-out, so access is limited to critical operations.
guest(6)- client is not Dot1x capable, so allowed guest role access.
|
| ruckusWiredClientDescr snSwitch.43.1.1.1.1.6
Syntax:
SnmpAdminString
|
Read-only
|
Describes the client as derived from LLDP/CDP device description for LLDP/CDP learned
devices. Otherwise, it's an empty string.
|
| ruckusWiredClientUserName snSwitch.43.1.1.1.1.7
Syntax:
SnmpAdminString
|
Read-only
|
Specifies the username associated with the client that is represented by this entry.
If the username is not present or not applicable, then it can be username or MAC address.
|
| ruckusWiredClientV4Addr snSwitch.43.1.1.1.1.8
Syntax:
InetAddressIPv4
|
Read-only
|
Specifies the IPv4 address of the client represented by this entry. A client can have
both IPv4 and IPv6 addresses bound on dual-stack hosts.
|
| ruckusWiredClientV6Addr snSwitch.43.1.1.1.1.9
Syntax:
InetAddressIPv6
|
Read-only
|
Specifies the IPv6 address of the client represented by this entry. A client can have
both IPv4 and IPv6 addresses bound on dual-stack hosts.
|
| ruckusWiredClientUpTime snSwitch.43.1.1.1.1.10 Syntax: TimeTicks
|
Read-only
|
Specifies the time the client had been up when the client entry is created in the
Ruckus device.
|
| ruckusWiredClientTxPkts snSwitch.43.1.1.1.1.11 Syntax: Counter64
|
Read-only
|
The total number of packets transmitted on this port for this client.
|
| ruckusWiredClientRxPkts snSwitch.43.1.1.1.1.12 Syntax: Counter64
|
Read-only
|
The total number of packets received on this port for this client.
|
| ruckusWiredClientTxOctets snSwitch.43.1.1.1.1.13 Syntax: Counter64
|
Read-only
|
The total number of octets transmitted on this port for this client.
|
ruckusWiredClientRxOctets
snSwitch.43.1.1.1.1.14 Syntax: Counter64
|
Read-only
|
The total number of octets received on this port for this client.
|
| ruckusDhcpClientHostName snSwitch.43.1.1.1.1.15 Syntax:
snmpAdminString
|
Read-only |
Captures the hostname of the DHCP client. |
| ruckusDhcpClientDeviceTypeName snSwitch.43.1.1.1.1.16 Syntax:
snmpAdminString
|
Read-only |
Specifies the type of device, such as a smartphone, laptop, or
printer, based on DHCP information. |
|
ruckusDhcpClientOsVendorName
snSwitch.43.1.1.1.1.17
Syntax: snmpAdminString
|
Read-only |
Identifies the vendor of the operating system on the client
device. |
|
ruckusDhcpClientModelName
snSwitch.43.1.1.1.1.18
Syntax: snmpAdminString
|
Read-only |
Specifies the model name of the DHCP client device. |