The IP static route table contains a list of static routes. These routes can be one
of the following types:
Standard: The static route consists of the destination network address and network
mask, plus the IP address of the next-hop gateway.
Interface-based: The static route consists of the destination network address and
network mask, plus the Layer 3 switch interface through which you want the Layer 3
switch to send traffic for the route. Typically, this type of static route is directly
attached to the destination networks.
Null: The static route consists of the destination network address and network mask,
plus the “null0” parameter. Typically, the null route is configured as a backup route
for discarding traffic if the primary route is unavailable.
The IP static route table also serves as the default route table.
SNMP does not support Equal-Cost Multipath(ECMP). The snRtIpStaticRouteTable uses
the IP address and mask as table indexes and displays one path even if the user configures
multiple paths (next hop IP address or outgoing interface).
Note: SNMP support for the IP static route MIB table is limited to IPv4 only and not supported
on IPv6. Operations such as SNMP GET, SNMP WALK, and SNMP SET are supported.
Note: The following MIB table OIDs support only the default VRF, and the non-default VRF
is not supported.
Note: The snRtIpStaticRouteIndex OID is not supported on the ICX devices.
Name, OID, and syntax
Access
Description
snRtIpStaticRouteTable
1.3.6.1.4.1.1991.1.2.2.2
None
IP static route table.
snRtIpStaticRouteEntry
1.3.6.1.4.1.1991.1.2.2.2.1
Syntax: Integer32
Read-only
The table index for a static route entry.
snRtIpStaticRouteDest
1.3.6.1.4.1.1991.1.2.2.2.1.1
Syntax: IpAddress
Read-write
Shows the destination IP address of the default route. The address 0.0.0.0 is the
IP address of the default router.
Note: The OID value of snRtIpStaticRouteDest must be the same as the snRtIpStaticRouteDest
index value used to create the row. The index and index value must be the same. The
SNMP SET value must be a valid IP address.
snRtIpStaticRouteMask
1.3.6.1.4.1.1991.1.2.2.2.1.2
Syntax: IpAddress
Read-write
Shows the subnet mask of the default router destination IP address. The subnet mask
of the default router is 0.0.0.0.
The OID value of snRtIpStaticRouteMask must be the same as the snRtIpStaticRouteMask
index value used to create the row. The index and index value must be the same. The
SNMP SET value must be a valid IP address.
snRtIpStaticRouteNextHop
1.3.6.1.4.1.1991.1.2.2.2.1.3
Syntax: IpAddress
Read-write
Shows the IP address of the next-hop router (gateway) for the route. The SNMP SET
value must be a valid IP address.
snRtIpStaticRouteMetric
1.3.6.1.4.1.1991.1.2.2.2.1.4
Syntax: Integer32
Read-write
Shows the metrics to the next-hop router.
snRtIpStaticRouteRowStatus
1.3.6.1.4.1.1991.1.2.2.2.1.5
Syntax: Integer
Read-write
Controls the management of the table rows. The following values can be written:
delete(3): Delete the row.
create(4): Create a new row.
snRtIpStaticRouteDistance
1.3.6.1.4.1.1991.1.2.2.2.1.6
Syntax: Integer
Read-write
Specifies the administrative distance of the route. When comparing equal routes to
a destination, the Layer 3 switch prefers lower administrative distances over higher
ones.
snRtIpStaticRouteOutgoingInterface
1.3.6.1.4.1.1991.1.2.2.2.1.7
Syntax: Integer
Read-only
Displays the outgoing interface of the
static route in SNMP snRtIpStaticRouteTable. Only the SNMP GET
operation is supported. The type of outgoing interface can be
Ethernet, LAG, tunnel, or VE. Please note that this OID only
displays the outgoing interface if user explicitly configures one as
a part of static route configuration which is equivalent to
show ip static route command. If the user
configures a nexthop IP address, then the outgoing interface is not
shown in this table.
Note: The
snRtIpStaticRouteOutgoingInterface OID is not supported for a
static route which is configured with null0.