Switch port information

1.3.6.1.4.1.1991.1.1.3.3.5

None

The switch port information table.

1.3.6.1.4.1.1991.1.1.3.3.5.1.1

Syntax: InterfaceIndex

Read-only

Shows the port or interface index.

1.3.6.1.4.1.1991.1.1.3.3.5.1.2

Syntax: Integer

Read-write

1.3.6.1.4.1.1991.1.1.3.3.5.1.3

Syntax: Integer

Read-write

Contains a list of port or interface indexes (ifindex) that mirror this interface when monitoring is enabled.

1.3.6.1.4.1.1991.1.1.3.3.5.1.4

Syntax: Integer

Read-write

Indicates if the port has an 802.1q tag:

• tagged(1) - Ports can have multiple VLAN IDs because these ports can be members of more than one VLAN.
• untagged(2) - There is only one VLAN ID per port.

1.3.6.1.4.1.1991.1.1.3.3.5.1.5

Syntax: Integer32

Read-only

Indicates the IEEE 802.1q tag type of an interface. The tag type is embedded in the two octets in the length or type field of an Ethernet packet. It specifies that the two octets after the length or type field in an Ethernet packet is the tag value.

Default value: 33024

1.3.6.1.4.1.1991.1.1.3.3.5.1.6

Syntax: Integer

Read-write

Indicates if the port operates in half- or full-duplex mode:

• none(0) - This is not used.
• halfDuplex(1) - Half-duplex mode. Available only for 10/100 Mbps ports.
• fullDuplex(2) - Full-duplex mode. 100BaseFx, 1000BaseSx, and 1000BaseLx ports operate only at fullDuplex(2).

The read-back channel status from hardware is as follows:

• halfDuplex(1) - Half-duplex mode.
• fullDuplex(2) - Full-duplex mode.

The port media type (expansion or regular) and port link type (trunk or feeder) determine the value of this object. The port cannot be set to half-duplex mode if the port connect mode is m200e(4). However, the value of this parameter may be automatically set whenever the expansion port is connected, for example, in the case of a cascade-connecting device.

1.3.6.1.4.1.1991.1.1.3.3.5.1.7

Syntax: Integer

Read-write

Indicates the speed configuration for a port:

• none(0) - Link down or no traffic.
• sAutoSense(1) - Auto-sensing 10 or 100 Mbps.
• s10M(2) - 10 Mbps.
• s100M(3) - 100 Mbps.
• s1G(4) - 1 Gbps.
• s1GM(5) - 1 Gbps master.
• s155M(6) - 155 Mbps (ATM) (for expansion board only).
• s10G(7) - 10 Gbps.
• s622M(8)
• s2488M(9)
• s9953M(10)
• s16G(11) - 16 Gbps.
• sOpticBased(12)
• s40G(13) - 40 Gbps.
• S2500M(14) - 2.5 Gbps.
• S5000M(15) - 5 Gbps.
• S100G(16) - 100 Gbps.
• S25G (17) - 25 Gbps.

The read-back hardware status is the following:

• none(0) - Link down or no traffic.
• s10M(2) - 10 Mbps.
• s100M(3) - 100 Mbps.
• s1G(4) - 1G bits per second.
• s1GM(5) - 1G bits per second master.
• s155M(6) - 155 Mbps (ATM) (for expansion board only).
• s10G(7) - 10 Gbps.
• s16G(11) - 16 Gbps.
• s40G(13) - 40 Gbps.
• S2500M(14) - 2.5 Gbps.

The port media type (expansion or regular) and port link type (trunk or feeder) determine whether this object can be written and the valid values for this object. It is not allowed to change speed for trunk ports. For expansion ports, all of the listed speeds can be set; however, the value of this parameter may be automatically set whenever the expansion port is connected, for example, in the case of a cascade-connecting device.

1.3.6.1.4.1.1991.1.1.3.3.5.1.8

Syntax: Integer

Read-only

Shows the media type for the port:

• other(1) - Other or unknown media.
• m100BaseTX(2) - 100 Mbps copper.
• m100BaseFX(3) - 100 Mbps fiber.
• m1000BaseFX(4) - 1 Gbps fiber.
• mT3(5) - 45 Mbps (T3).
• m155ATM(6) - 155 Mbps (ATM).
• m1000BaseTX(7) - 1 Gbps copper.
• m622ATM(8) - 622 Mbps (ATM).
• m155POS(9) - 155 Mbps (POS).
• m622POS(10) - 622 Mbps (POS).
• m2488POS(11) - 2488 Mbps (POS).
• m10000BaseFX(12) - 10 Gbps fiber.
• m16GStacking(14) - 16 Gbps fiber.
• m100GBaseFX(15) - 100 Gbps fiber.
• m40GStacking(16) - 40 Gbps fiber.
• m40GBaseFX(17) - 40 Gbps fiber.
• m10000BaseTX(18) - 10 Gbps copper.
• m2500BaseTX(19) - 2.5 Gbps.
• m100GBaseTX(20) - 100 Gbps fiber.
• mMultiGigBZ(21) - 2.5G/5G/10G multiGig per seconnd fiber.
• m40GBaseTX(22) - 40 Gbps fiber.
• m25GBaseTX(23) - 25 Gbps fiber.

1.3.6.1.4.1.1991.1.1.3.3.5.1.9

Syntax: Integer

Read-only

Shows the type of connector that the port offers:

• other(1) - Other or unknown connector.
• copper(2) - Copper connector.
• fiber(3) - Fiber connector. This describes the physical connector type.
• both(4) - Supports both Copper and Fiber.

1.3.6.1.4.1.1991.1.1.3.3.5.1.10

Syntax: Integer

Read-write

Shows the desired state of all ports:

• up(1) - Ready to pass packets
• down(2)
• testing(3) - No operational packets can be passed (same as ifAdminStatus in MIB-II)

1.3.6.1.4.1.1991.1.1.3.3.5.1.11

Syntax: Integer

Read-only

Shows the current operational state of the interface:

• up(1) - Ready to pass packets
• down(2)
• testing(3) - No operational packets can be passed (same as ifAdminStatus in MIB-II)

1.3.6.1.4.1.1991.1.1.3.3.5.1.12

Syntax: Integer

Read-write

Indicates the Quality of Service (QoS) level selected for the port:

• low(0) - Low priority
• high(1) - High priority
• level0(0)
• level1(1)
• level2(2)
• level3(3)
• level4(4)
• level5(5)
• level6(6)
• level7(7)

1.3.6.1.4.1.1991.1.1.3.3.5.1.13

Syntax: Physical address

Read-only

Shows the physical address of the port.

1.3.6.1.4.1.1991.1.1.3.3.5.1.14

Syntax: Integer

Read-write

Indicates the number of source MAC addresses that are allowed on the interface.

Valid values: 0 through 2048. The value 0 means an unlimited number of addresses are allowed.

Default: 8

1.3.6.1.4.1.1991.1.1.3.3.5.1.15

Syntax: Integer

Read-write

Indicates if STP is enabled for the port:

• disabled(0)
• enabled(1)

1.3.6.1.4.1.1991.1.1.3.3.5.1.16

Syntax: Integer

Read-write

Specifies the ID for a DHCP gateway list entry relative to this switch port.

Valid values: 0 through 32. A value of 0 means that the ID is unassigned.

1.3.6.1.4.1.1991.1.1.3.3.5.1.17

Syntax: Display string

Read-write

Indicates the port name or description. This description may have been entered using the CLI.

Valid values: Up to 32 characters for most devices.

1.3.6.1.4.1.1991.1.1.3.3.5.1.18

Syntax: Display string

Read-only

A textual string containing the slot or port information about the interface.

1.3.6.1.4.1.1991.1.1.3.3.5.1.19

Syntax: Integer

Read-write

Applies only to Gigabit Ethernet ports.

Indicates if auto-negotiation mode is enabled on the port:

• disabled(0) - The port will be placed in non-negotiation mode.
• enabled(1) - The port will start auto-negotiation indefinitely until it succeeds.
• negFullAuto(2) - The port will start with auto-negotiation. If the negotiation fails, then it will automatically switch to non-negotiation mode. This option is not supported in stackable products with Gigabit Ethernet ports.
• global(3) - The port negotiation mode follows the value of snSwGlobalAutoNegotiate.
• other(4) - Non-Gigabit Ethernet port returns this value.

Default: global(3)

1.3.6.1.4.1.1991.1.1.3.3.5.1.20

Syntax: Integer

Read-write

Indicates if port flow control is enabled:

• disable(0)
• enable(1)

Default: enabled(1)

1.3.6.1.4.1.1991.1.1.3.3.5.1.21

Syntax: Integer

Read-only

Applies only to Gigabit Ethernet ports.

Shows the media type for the port:

• m1000BaseSX(0) - 1-Gbps fiber, with a short wavelength transceiver
• m1000BaseLX(1) - 1-Gbps fiber, with a long wavelength transceiver (3 km)
• m1000BaseLH(2) - 1-Gbps fiber, with a special wavelength transceiver (50 km)
• m1000BaseLHB(4) - 1-Gbps fiber, with a special wavelength transceiver (150 km)
• m1000BaseTX(5) - 1-Gbps copper (100 m)
• m10000BaseSR(6) - 10-Gbps fiber, with a short range wavelength transceiver (100 m)
• m10000BaseLR(7) - 10-Gbps fiber, with a long range wavelength transceiver (10 km)
• m10000BaseER(8) - 10-Gbps fiber, with an extended range wavelength transceiver (40 km)
• sfpCWDM1470nm80Km(9) - 1-Gbps CWDM fiber, with a wavelength 1470nm, reach 80 kms
• sfpCWDM1490nm80Km(10) - 1-Gbps CWDM fiber, with a wavelength 1490nm, reach 80 kms
• sfpCWDM1510nm80Km(11) - 1-Gbps CWDM fiber, with a wavelength 1510nm, reach 80 kms
• sfpCWDM1530nm80Km(12) - 1-Gbps CWDM fiber, with a wavelength 1530nm, reach 80 kms

• sfpCWDM1550nm80Km(13) - 1-Gbps CWDM fiber, with a wavelength 1550nm, reach 80 kms
• sfpCWDM1570nm80Km(14) - 1-Gbps CWDM fiber, with a wavelength 1570nm, reach 80 kms
• sfpCWDM1590nm80Km(15) - 1-Gbps CWDM fiber, with a wavelength 1590nm, reach 80 kms
• sfpCWDM1610nm80Km(16) - 1-Gbps CWDM fiber, with a wavelength 1610nm, reach 80 kms
• sfpCWDM1470nm100Km(17) - 1-Gbps CWDM fiber, with a wavelength 1470nm, reach 100 kms
• sfpCWDM1490nm100Km(18) - 1-Gbps CWDM fiber, with a wavelength 1490nm, reach 100 kms
• sfpCWDM1510nm100Km(19) - 1-Gbps CWDM fiber, with a wavelength 1510nm, reach 100 kms
• sfpCWDM1530nm100Km(20) - 1-Gbps CWDM fiber, with a wavelength 1530nm, reach 100 kms
• sfpCWDM1550nm100Km(21) - 1-Gbps CWDM fiber, with a wavelength 1550nm, reach 100 kms
• sfpCWDM1570nm100Km(22) - 1-Gbps CWDM fiber, with a wavelength 1570nm, reach 100 kms
• sfpCWDM1590nm100Km(23) - 1-Gbps CWDM fiber, with a wavelength 1590nm, reach 100 kms

snSwIfInfoGigType

(continued)

• sfpCWDM1610nm100Km(24) - 1-Gbps CWDM fiber, with a wavelength 1610nm, reach 100 kms
• m1000BaseLHX(25) - 1-Gbps fiber, with a special wavelength transceiver (150 km)
• m1000BaseLMC(35) - Link Media Copper
• mXFP10000BaseSR(36) - 10GBASE fiber, 850nm serial pluggable XFP optic (LC), target range 300 m over MMF
• mXFP10000BaseLR(37) - 10GBASE fiber, 1310nm serial pluggable XFP optic (LC) for up to 10 km over SMF
• mXFP10000BaseER(38) - 10GBASE fiber, 1550nm serial pluggable XFP optic (LC) for up to 40 km over SMF
• mXFP10000BaseSW(39) - Not used
• mXFP10000BaseLW(40) - Not used
• mXFP10000BaseEW(41) - Not used
• mXFP10000BaseCX4(42) - 10GBASE-CX4, XFP module, 15 m, CX4 connector
• mXFP10000BaseZR(43) - 1550nm serial pluggable XFP optic (LC) for up to 80 km over SMF
• mXFP10000BaseZRD(44) - 10GBASE-ZR DWDM, XFP optic, 80 km
• mXFP10000BaseSRSW(46) - Same as mXFP10000BaseSR(36)

• mXFP10000BaseLRLW(47) - Same as mXFP10000BaseLR(37)
• mXFP10000BaseEREW(48) - Same as mXFP10000BaseER(38)
• m100GBaseTX(51) - 100G BASE fiber
• m1000BaseXGSR(136) - 10G BASE fiber
• mMultiGigBZ(52) - 2.5/5/10 multiGig fiber
• m40GBaseTX(53) - 40GBASE fiber
• m25GBaseTX(54) - 25GBASE fiber
• notApplicable(255) - A non-gigabit port
• mCFP100GBaseSR10(145) - 100-GbE CFP optic (MPO 2x12), SR10, for distances up to 100 m over MMF
• mCFP100GBaseLR4(146) - 100-GbE CFP optic (SC), LR4, for distances up to 10 km over SMF
• mCFP100GBaseER4(147) - 100-GbE CFP optic, ER4, for distances up to 40 km over SMF
• mCFP100GBase10x10g2Km(148) - 100-GbE CFP optic (LC), 10x10, for distances up to 2 km over SMF
• mCFP100GBase10x10g10Km(149) - 100-GbE CFP optic (LC), 10x10, for distances up to 10 km over SMF
• qSFP40000BaseSR4(150) - SR proper value for 40G
• qSFP40000Base10KmLR4(151) - LR proper vallue for 40G
• mCFP2-100GBaseSR10(154)
• mCFP2-100GBaseLR4(155)
• mCFP2-100GBaseER4(156)
• mCFP2-100GBase10x10g2Km(157)
• mCFP2-100GBase10x10g10Km(158)

1.3.6.1.4.1.1991.1.1.3.3.5.1.22

Syntax: Integer

Read-write

Indicates if fast span is enabled on the port:

• disabled(0)
• enabled(1)

1.3.6.1.4.1.1991.1.1.3.3.5.1.23

Syntax: Integer

Read-write

Indicates if fast span uplink is enabled on the port:

• disabled(0)
• enabled(1)

1.3.6.1.4.1.1991.1.1.3.3.5.1.25

Syntax: Integer

Read-write

Indicates if Layer 2 switching is enabled on a routing switch port:

• disabled(0) - Instructs the routing switch to perform routing first. If that fails, it performs switching.
• enabled(1) - Instructs the routing switch to perform routing only.

For a Layer 2 switching-only product, reading this object always returns "disabled". Writing "enabled" to this object takes no effect.

Default: disabled(0)

1.3.6.1.4.1.1991.1.1.3.3.5.1.26

Syntax: Integer

Read-only

Indicates if the mini-GBIC optic is absent or present:

• false(0)
• true(1)

1.3.6.1.4.1.1991.1.1.3.3.5.1.27

Syntax: Integer

Read-only

Indicates if the Gigabit port has a GBIC or miniGBIC port:

• GBIC(1) - GBIC
• miniGBIC(2) - MiniGBIC
• empty(3) - GBIC is missing
• other(4) - Not a removable Gigabit port

1.3.6.1.4.1.1991.1.1.3.3.5.1.28

Syntax: Integer

Read-write

Shows the number of seconds for which average port utilization should be calculated.

Valid values: 30 through 300, in 30-second increments.

Default: 300 seconds

1.3.6.1.4.1.1991.1.1.3.3.5.1.29

Syntax: Counter32

Read-only

Shows the total number of packets received on the interface.

1.3.6.1.4.1.1991.1.1.3.3.5.1.30

Syntax: Counter32

Read-only

Shows the total number of packets transmitted out of the interface.

1.3.6.1.4.1.1991.1.1.3.3.5.1.31

Syntax: Counter32

Read-only

Shows the number of dot3StatsAlignmentErrors, which consists of frames received on a particular interface that are not an integral number of octets in length and do not pass the FCS check.

The count represented by an instance of this object is incremented when the alignmentError status is returned by the MAC service to the LLC (or other MAC user). According to the conventions of IEEE 802.3 Layer Management, received frames for which multiple error conditions are obtained are counted exclusively according to the error status presented to the LLC.

1.3.6.1.4.1.1991.1.1.3.3.5.1.32

Syntax: Counter32

Read-only

Shows the number of dot3StatsFCSErrors, which consists of frames received on a particular interface that are an integral number of octets in length but do not pass the FCS check.

The count represented by an instance of this object is incremented when the frameCheckError status is returned by the MAC service to the LLC (or other MAC user). According to the conventions of IEEE 802.3 Layer Management, received frames for which multiple error conditions are obtained are counted exclusively according to the error status presented to the LLC.

1.3.6.1.4.1.1991.1.1.3.3.5.1.33

Syntax: Counter32

Read-only

Shows the number of dot3StatsMultipleCollisionFrames, which consists of successfully transmitted frames on a particular interface for which transmission is inhibited by more than one collision.

A frame that is counted by an instance of this object is also counted by the corresponding instance of ifOutUcastPkts, ifOutMulticastPkts, or ifOutBroadcastPkts and is not counted by the corresponding instance of the dot3StatsSingleCollisionFrames object.

1.3.6.1.4.1.1991.1.1.3.3.5.1.34

Syntax: Counter32

Read-only

Shows the number of successfully transmitted frames on a particular interface for which transmission is inhibited by more than one collision. This count is a combination of the dot3StatsSingleCollisionFrames and dot3StatsMultipleCollisionFrames objects.

1.3.6.1.4.1.1991.1.1.3.3.5.1.35

Syntax: Counter32

Read-only

Shows the number of successfully received frames on a particular interface for which transmission is inhibited by more than one collision.

1.3.6.1.4.1.1991.1.1.3.3.5.1.36

Syntax: Counter32

Read-only

Shows the number of dot3StatsFrameTooLongs, which consists of frames received on a particular interface that exceed the maximum permitted frame size.

The count represented by an instance of this object is incremented when the frameTooLong status is returned by the MAC service to the LLC (or other MAC user). According to the conventions of IEEE 802.3 Layer Management, received frames for which multiple error conditions are obtained are counted exclusively according to the error status presented to the LLC.

1.3.6.1.4.1.1991.1.1.3.3.5.1.37

Syntax: Counter32

Read-only

Shows the number frames received on a particular interface that are below the minimum permitted frame size.

1.3.6.1.4.1.1991.1.1.3.3.5.1.38

Syntax: Counter32

Read-write

Shows the total number of broadcast packets received on the interface.

1.3.6.1.4.1.1991.1.1.3.3.5.1.39

Syntax: Counter32

Read-only

Shows the total number of broadcast packets transmitted out of the interface.

1.3.6.1.4.1.1991.1.1.3.3.5.1.40

Syntax: Counter32

Read-only

Shows the total number of multicast packets received on the interface.

1.3.6.1.4.1.1991.1.1.3.3.5.1.41

Syntax: Counter32

Read-only

Shows the total number of multicast packets transmitted out of the interface.

1.3.6.1.4.1.1991.1.1.3.3.5.1.42

Syntax: Counter32

Read-only

Shows the number of inbound packets that will be discarded even though they have no errors. These packets will be discarded to prevent them from being delivered to a higher-layer protocol. For example, packets may be discarded to free up buffer space.

1.3.6.1.4.1.1991.1.1.3.3.5.1.43

Syntax: Counter32

Read-only

Shows the number of outbound packets that will be discarded even though they contain no errors. For example, packets may be discarded to free up buffer space.

1.3.6.1.4.1.1991.1.1.3.3.5.1.44

Read-only

Shows the total number of MAC Stations connected to the interface.

1.3.6.1.4.1.1991.1.1.3.3.5.1.45

Syntax: Counter32

Read-only

Shows the total number of link state changes on the interface.

1.3.6.1.4.1.1991.1.1.3.3.5.1.46

Syntax: Counter64

Read-only

Shows the total number of octets received on the interface, including framing characters. This object is a 64-bit counter of the ifInOctets object defined in RFC 1213. The octet string is in big-endian byte order.

This object has eight octets.

1.3.6.1.4.1.1991.1.1.3.3.5.1.47

Syntax: Counter64

Read-only

Shows the total number of octets transmitted out of the interface, including framing characters. This object is a 64-bit counter of the ifOutOctets object, defined in RFC 1213. The octet string is in big-endian byte order.

This object has eight octets.

1.3.6.1.4.1.1991.1.1.3.3.5.1.48

Syntax: Gauge32

Read-only

Shows the number of bits per second received on the interface over a five-minute interval.

1.3.6.1.4.1.1991.1.1.3.3.5.1.49

Syntax: Gauge32

Read-only

Shows the number of bits per second transmitted out of the interface over a five-minute interval.

1.3.6.1.4.1.1991.1.1.3.3.5.1.50

Syntax: Gauge32

Read-only

Shows the number of packets per second received on the interface over a five-minute interval.

1.3.6.1.4.1.1991.1.1.3.3.5.1.51

Syntax: Gauge32

Read-only

Shows the number of packets per second transmitted out of the interface over a five-minute interval.

1.3.6.1.4.1.1991.1.1.3.3.5.1.52

Syntax: Integer

Read-only

Indentifies the input network utilization in hundredths of a percent over a five-minute interval.

Valid values: 0 through 10000

1.3.6.1.4.1.1991.1.1.3.3.5.1.53

Syntax: Integer

Read-only

Shows the output network utilization in hundredths of a percent over a five-minute interval.

Valid values: 0 through 10000

1.3.6.1.4.1.1991.1.1.3.3.5.1.54

Syntax: Unsigned32

Read-only

Shows the bit rate, in kilobits per second, received on a 10 Gigabit or faster interface within a five-minute interval.

1.3.6.1.4.1.1991.1.1.3.3.5.1.55

Syntax: Unsigned32

Read-only

Shows the bit rate, in kilobits per second, transmitted from a 10 Gigabit or faster interface within a five-minute interval.

1.3.6.1.4.1.1991.1.1.3.3.5.1.56

Syntax: Counter64

Read-only

The total number of jumbo packets received on the interface.

1.3.6.1.4.1.1991.1.1.3.3.5.1.57

Syntax: Counter64

Read-only

The total number of jumbo packets transmitted out of the interface.

1.3.6.1.4.1.1991.1.1.3.3.5.1.62

Syntax: PhysAddress

Read-only

The port’s native MAC address. The native MAC address represents the switch port.

1.3.6.1.4.1.1991.1.1.3.3.5.1.63

Syntax: Integer

Read-write

Enables or disables the monitoring egress drop counter on the port.

This OID is enabled by default on ICX platforms.

Valid values:

• disable(0)
• enable(1)

1.3.6.1.4.1.1991.1.1.3.3.5.1.64

Syntax: Integer

Read-only

Displays the state for the Long Reach Module (LRM) adapter presented on this port. Some ICX devices support LRM optics on 10-Gbps fiber ports. The LRM adapter is used to support LRM optics on those switch ports.

Valid values are false and true. The default is the false state.

• false: The port is not connected to LRM adapter
• true: The port is connected to LRM adapter

1.3.6.1.4.1.1991.1.1.3.3.5.1.65

Syntax: TruthValue

Read-write

The status of the spanning tree BPDU guard on an Ethernet port.

The default is the false state.

1.3.6.1.4.1.1991.1.1.3.3.5.1.66

Syntax: TruthValue

Read-write

The status of the spanning tree root guard on an ethernet port. Declares the port to be on root guard for all spanning trees.

The default is the false state.

1.3.6.1.4.1.1991.1.1.3.3.5.1.67

Syntax: TruthValue

Read-write

The status of the rapid spanning tree admin edge port on an Ethernet port. Declares the port to be an operational edge for all VLANs.

The default is the false state.

1.3.6.1.4.1.1991.1.1.3.3.5.1.68

Syntax: Integer

Read-write

The port can be configured to operate in either master or slave mode. The values are:

• none(0) - Not configured or not supported for clock mode, like fiber ports.
• master(1) - Master mode

• slave(2) - Slave mode

• auto(3) - Auto mode is the default value for copper ports.

1.3.6.1.4.1.1991.1.1.3.3.5.1.69

Syntax: TruthValue

Read-write

This is a new MIB object for the protected mode at the port level. The default is false state.

1.3.6.1.4.1.1991.1.1.3.3.5.1.70

Syntax: TruthValue

Read-write

The status of Trust DSCP at Port Level QoS/VOIP settings.

• (1) - Trust DSCP is configured.
• (2) - Trust DSCP is not configured (Default).

1.3.6.1.4.1.1991.1.1.3.3.5.1.71

Syntax: Integer32

Read-write

• Configure voice VLAN
• Read the voice VLAN config

snSwIfPortLoopDetectionMode

1.3.6.1.4.1.1991.1.1.3.3.5.1.72

Syntax: TruthValue

Read-write

Specifies whether Loop Detection is enabled on the Interface or not.

Possible Values are:

2: Not Enabled

1: Enabled

snSWIfErrDisableStatus

1.3.6.1.4.1.1991.1.1.3.3.5.1.73

Syntax: Integer

Read-only

The port's error disable status. Possible values are:

• not-error-disable(0) the port is not under error disable state.
• bpdu-guard(1) ERRDISABLE_BPDUGUARD
• loop-detection(2) ERRDISABLE_LOOP_DETECTION
• invalid-licence(3) ERRDISABLE_INVALID_LICENSE
• packet-inerror(4) ERRDISABLE_PACKET_INERROR
• loam-remote-critical-error(5) ERRDISABLE_LOAM_REM_CRITICAL_EVENT
• needs-reboot(6) ERRDISABLE_NEEDS_REBOOT
• bcast-threshold-exceed(7) ERRDISABLE_BCAST_THRESHOLD_EXCEEDED
• mcast-threshold-exceed(8) ERRDISABLE_MCAST_THRESHOLD_EXCEEDED
• dlf-threshold-exceed(9) ERRDISABLE_UNKNOWN_UCAST_THRESHOLD_EXCEEDED
• stack-port-problem(10) ERRDISABLE_STK_PORT_PROBLEM
• spx-invalid-topo(11) ERRDISABLE_SPX_INVALID_TOPO
• pvst-protect(12) ERRDISABLE_PVST_PROTECT
• bpdu-tunnel-threshold-exceed(13) ERRDISABLE_BPDU_TUN_THRESHOLD_EXCEEDED
• lag-oper-speed-mismatch(14) ERRDISABLE_LAG_OPER_SPEED_MISMATCH
• cause-counter(15) ERRDISABLE_CAUSE_CNT, this is not a valid reason, just the reason counter

1.3.6.1.4.1.1991.1.1.3.3.5.1.74

Syntax: Integer

0: Disable - Disables breakout on the port.

1: Enable - Enables breakout on the port.

1.3.6.1.4.1.1991.1.1.3.3.5.1.75

Syntax: Integer

Read-only

Shows the status of the rapid spanning tree (RSTP) point-to-point connection on an Ethernet port. It indicates whether the port is directly linked to a single RSTP-capable device for all VLANs.

• auto (0): The port is in auto mode by default.
• disable (1): The port is configured but currently disabled.
• enable (2): The port is configured and currently enabled.

1.3.6.1.4.1.1991.1.1.3.3.12

1.3.6.1.4.1.1991.1.1.3.3.12.1

An entry in the snSwIfInfoLimitTable indicates the configuration on a specified port for rate limiting values.

1.3.6.1.4.1.1991.1.1.3.3.12.1.1

Syntax: Integer

Read-only

The type of the limit. The value specified applies for broadcast, unknown unicast, and multicast traffic.

1.3.6.1.4.1.1991.1.1.3.3.12.1.2

Syntax: Unsigned32

Read-only

Limit the number of packets per second forwarded out of the switch port. Setting the value to 0 disables the limitation check. The default value is 0.

1.3.6.1.4.1.1991.1.1.3.3.12.1.3

Syntax: Unsigned32

Read-only

Limit the number of kilobytes per second forwarded out of the switch port. Setting the value to 0 disables the limitation check. The default value is 0.

1.3.6.1.4.1.1991.1.1.3.3.12.1.4

Syntax: Unsigned32

Read-only

The number of packets to be dropped when the rate limit is reached before taking the specified action (such as shutting down the port).

1.3.6.1.4.1.1991.1.1.3.3.12.1.5

Syntax: Unsigned32

Read-only

Specifies the time the port should be in the down state. Takes effect only if the threshold is configured. The default value is 300.

1.3.6.1.4.1.1991.1.1.3.3.12.1.6

Syntax: Unsigned32

Read-only