RUCKUS-ACL-MIB Table

The following table gives the management information for describing the MAC ACLs, IPv4 ACLs, IPv6 ACLs, bindings on ports, VLANs, and VLAN and port combinations.
Name, OID, and syntax Access Description
AclName

Syntax: DisplayString (SIZE (1..48))

Not-accessible

A name that identifies an access-list like IPv4, IPv6 or MAC ACLs.

AclPolicyName

Syntax: DisplayString (SIZE (1..8))

Not-accessible

A name that identifies a traffic policy which can applied with IPv4, IPv6 ACL filters.

AclType

Syntax: Integer

Not-accessible Describes the type of ACL. The values are:

MAC(1)

IPv4(2)

IPv6(3)

AclAction

Syntax: Integer

Not-accessible Specifies an action for ACL filter. The values are:

deny(1)

permit(2)

AclOperator

Syntax: Integer

Not-accessible

Represents the operator value like equal, not-equal, lesser than, greater than, range and none. The values are:

equal(1)

not equal(2)

less than(3)

greater than(4)

range(5)

none(6)

AclDirection

Syntax: Integer

Not-accessible

The packet flow direction on interface, where the ACL should be applied. It can be either ingress or egress direction, or both the direction. The values are:

ingress(1)

egress(2)

IpPrecedence

Syntax: Integer

Not-accessible The IP precedence value which can be used with L3 ACL filter. The values are:

routine(1)

priority(2)

immediate(3)

flash(4)

flashOverride(5)

critical(6)

internet(7)

network(8)

other(9)

IpTos

Syntax: Integer

Not-accessible The IP TOS value which can be used with L3 ACL filter. The values are:

normal(1)

lowCost(2)

maxReliability(3)

maxThroughput(4)

minDelay(5)

EtherType

Syntax: Unsigned32

Not-accessible EtherType value from the ethernet packet shown in Hex format.
ruckusAclMIB

1.3.6.1.4.1.1991.1.1.3.45

Not-accessible The MIB module for managing ACLs.
ruckusAclNotify

1.3.6.1.4.1.1991.1.1.3.45.0

Not-accessible To notify the Access Control list change.
ruckusAclObjects

1.3.6.1.4.1.1991.1.1.3.45.1

Not-accessible Objects that define the Access Control list.
ruckusAcls

1.3.6.1.4.1.1991.1.1.3.45.1.1

Not-accessible Specifies the ACLs.
ruckusAclFilters

1.3.6.1.4.1.1991.1.1.3.45.1.2

Not-accessible Specifies the Access Control list filters.
ruckusIpv4Filters

1.3.6.1.4.1.1991.1.1.3.45.1.2.1

Not-accessible Specifies the IPv4 filters.
ruckusIpv6Filters

1.3.6.1.4.1.1991.1.1.3.45.1.2.2

Not-accessible Specifies the IPv6 filters.
ruckusMacFilters

1.3.6.1.4.1.1991.1.1.3.45.1.2.3

Not-accessible Specifies the MAC filters.
ruckusAclTable

1.3.6.1.4.1.1991.1.1.3.45.1.1.1

Not-accessible Table of RUCKUS IPv4 or IPv6 or MAC Access Control Lists (ACLs).
ruckusAclEntry

1.3.6.1.4.1.1991.1.1.3.45.1.1.1.1

Not-accessible An entry in the RUCKUS IPv4 or IPv6 or MAC Access Control List table.
ruckusAclType

1.3.6.1.4.1.1991.1.1.3.45.1.1.1.1.1

Syntax: AclType

Not-accessible Specifies the type of the ACL.
ruckusAclName

1.3.6.1.4.1.1991.1.1.3.45.1.1.1.1.2

Syntax: AclName

Not-accessible Unique Access Control List name for an entry.
ruckusAclAcctEnable

1.3.6.1.4.1.1991.1.1.3.45.1.1.1.1.3

Syntax: TruthValue

Read-Create Specifies if accounting is enabled for the filters in this ACL.
ruckusAclStandard

1.3.6.1.4.1.1991.1.1.3.45.1.1.1.1.4

Syntax: TruthValue

Read-Only Specifies the type of IPv4 ACL - standard or extended, if ACL is IPv4 ACL.
ruckusAclRowStatus

1.3.6.1.4.1.1991.1.1.3.45.1.1.1.1.5

Syntax: RowStatus

Read-Create

The row status variable is used according to installation and removal conventions for conceptual rows. Setting this object to CreateAndGo(4) results in the creation of the IPv4 or IPv6 or MAC ACL. Setting this object to destroy(6) removes the IPv4 or IPv6 or MAC ACL. All other values are ignored.

IPv4 ACL filter table

Name, OID, and syntax Access Description
ruckusIpv4AclFilterTable

1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1

Syntax: SEQUENCE OF RuckusIpv4AclFilterEntry

Not-accessible Table of Ruckus IPv4 Access Control List filters.
ruckusIpv4AclFilterEntry

1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1

Syntax: RuckusIpv4AclFilterEntry

Not-accessible An entry in the Ruckus IPv4 Access Control List Filter table.
ruckusIpv4AclFilterSeqNum

1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.1

Syntax: Unsigned32

Not-accessible Specifies the sequence number for this ACL filter.
ruckusIpv4AclFilterAction

1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.2

Syntax: AclAction

Read-create Action to take if the IP packet matches with this ACL filter.
ruckusIpv4AclFilterStdProtocol

1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.3

Syntax: Integer

Read-create

Standard transport protocols are allowed. The extended option enables the definition of other protocols using the OID ruckusIpv4AclFilterExtProtocol which takes any value.

ip(0)

icmp(1)

igmp(2)

tcp(6)

udp(17)

ip6(41)

rsvp(46)

gre(47)

esp(50)

ospf(89)

pim(103)

extended(255)

ruckusIpv4AclFilterExtProtocol

1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.4

Syntax: Integer

Read-create

Any transport protocol other than standard protocols mentioned with ruckusIpv4AclFilterStdProtocol OID. The value 0 means any protocol.

ruckusIpv4AclFilterSrcAddr

1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.5

Syntax: InetAddressIPv4

Read-create Source IPv4 address to match the packets.
ruckusIpv4AclFilterSrcMask

1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.6

Syntax: InetAddressIPv4

Read-create

Source IPv4 address mask used in combination with source IPv4 address to derive effective address for matching.

ruckusIpv4AclFilterSrcOperator

1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.7

Syntax: AclOperator

Read-create

Type of comparison to perform. For now, this applies only to TCP or UDP for comparing the port number.

ruckusIpv4AclFilterSrcPortLow

1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.8

Syntax: Unsigned32

Read-create

Specifies the TCP or UDP port number to match in packets. If the operator is "range", it specifies the start of the range.

ruckusIpv4AclFilterSrcPortHigh

1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.9

Syntax: Unsigned32

Read-create

Used only if the operator is defined as "range", where it specifies the end of the range.

ruckusIpv4AclFilterDestAddr

1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.10

Syntax: InetAddressIPv4

Read-create Destination IPv4 address to match in packets.
ruckusIpv4AclFilterDestMask

1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.11

Syntax: InetAddressIPv4

Read-create

Destination IPv4 address mask used in combination with source IPv4 address to derive effective address for matching.

ruckusIpv4AclFilterDestOperator

1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.12

Syntax: AclOperator

Read-create

Type of comparison to perform. For now, this only applies to TCP or UDP for comparing the port number.

ruckusIpv4AclFilterDestPortLow

1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.13

Syntax: Unsigned32

Read-create

Specifies the TCP or UDP port number to match in packets. If the operator is 'range', it specifies the start of range.

ruckusIpv4AclFilterDestPortHigh

1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.14

Syntax: Unsigned32

Read-create

Used only if the operator is defined as 'range', where it specifies the end of range.

ruckusIpv4AclFilterEstablished

1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.15

Syntax: TruthValue

Read-create

Enable or disable the filtering of established TCP packets of which the ACK or RESET flag is on. This filter only applies to the TCP transport protocol.

ruckusIpv4AclFilterPrecedence

1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.16

Syntax: IpPrecedence

Read-create Specifies the IP precedence value to match in packets.
ruckusIpv4AclFilterTos

1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.17

Syntax: IpTos

Read-create

Refers to the IP ToS value in the range 0 through 15, which is the sum of the numeric values of the following options:

0x0: Normal ToS

0x1: Minimum monetary cost ToS

0x2: Maximum reliability ToS

0x4: Maximum throughput ToS

0x8: Minimum delay

ruckusIpv4AclFilterIcmpType

1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.18

Syntax: Integer

Read-create

Specifies the ICMP type for matching if the protocol is ICMP. The value 0 means to ignore the field.

ruckusIpv4AclFilterIcmpCode

1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.19

Syntax: Integer

Read-create ICMP Message Code value. Used in combination with ICMP Message Type to set up an ICMP filter. This object is not used with any other protocol. The value 0 means to ignore the field. The supported values are:

Type: Echo reply

Type: Destination unreachable

Type: Source quench

Type: Redirect

Type: Echo request

Type: Router advertisement

Type: Router solicitation

Type: Time exceeded

Type: Parameter problem

Type: Timestamp request

Type: Timestamp reply

Type: Information request

Type: Information reply

Type: Address mask request

Type: Address mask reply

ruckusIpv4AclFilterExtIcmpType

1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.20

Syntax: Integer

Read-create

Any type that cannot be specified using the standard types can be specified using this object.

ruckusIpv4AclFilterPolicyName

1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.21

Syntax: AclPolicyName

Read-create Specifies the DSCP value to use in matching or marking.
ruckusIpv4AclFilterDscpMatch

1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.22

Syntax: Integer

Read-create Specifies the DSCP value for matching with this filter.
ruckusIpv4AclFilterDscpForce

1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.23

Syntax: Integer

Read-create

Specifies the DSCP value to be used for marking in outgoing packets matching this filter.

ruckusIpv4AclFilterPriorityMatch

1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.24

Syntax: Integer

Read-create Specifies the 802.1P priority for matching with this filter.
ruckusIpv4AclFilterPriorityForce

1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.25

Syntax: Integer

Read-create

Specifies the 802.1P priority to be used for marking in outgoing packets matching this filter.

ruckusIpv4AclFilterInternalPriority

1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.26

Syntax: Integer

Read-create QoS priority option for this filter.
ruckusIpv4AclFilterMirrorPkts

1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.27

Syntax: TruthValue

Read-create Mirror packets matching ACL permit clause.
ruckusIpv4AclFilterLogEnable

1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.28

Syntax: TruthValue

Read-create Specifies if logging is enabled for the filter.
ruckusIpv4AclFilterComments

1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.29

Syntax: DisplayString

Read-only Remark description of individual Access Control List entry.
ruckusIpv4AclFilterRowStatus

1.3.6.1.4.1.1991.1.1.3.45.1.2.1.1.30

Syntax: RowStatus

Read-create

The row status variable is used according to installation and removal conventions for conceptual rows. Setting this object to createAndGo(4) results in the creation of the IPv4 ACL filter. Setting this object to destroy(6) removes this IPv4 ACL filter. Other values are ignored.

IPv6 ACL filter table

Name, OID, and syntax Access Description
ruckusIpv6AclFilterTable

1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1

Syntax: SEQUENCE OF RuckusIpv6AclFilterEntry

Not-accessible Table of Ruckus IPv6 Access Control List Filters.
ruckusIpv6AclFilterEntry

1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1

Syntax: RuckusIpv6AclFilterEntry

Not-accessible An entry in the Ruckus IPv6 Access Control List Filter table.
ruckusIpv6AclFilterSeqNum

1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.1

Syntax: Unsigned32

Not-accessible Specifies the sequence number for this ACL filter.
ruckusIpv6AclFilterAction

1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.2

Syntax: AclAction

Read-create

Action to take if the IPv6 packet matches with this ACL filter.

ruckusIpv6AclFilterStdProtocol

1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.3

Syntax: Integer

Read-create

Standard transport protocols allowed. The extended option enables the definition of other protocols using the OID ruckusIpv6AclFilterExtProtocol which takes any value.

ruckusIpv6AclFilterExtProtocol

1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.4

Syntax: Integer

Read-create

Any transport protocol other than standard protocols mentioned with ruckusIpv6AclFilterStdProtocol OID. The value 0 means any protocol.

ruckusIpv6AclFilterSrcAddr

1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.5

Syntax: InetAddressIPv6

Read-create Source IPv6 address to match in packets.
ruckusIpv6AclFilterSrcPrefixLen

1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.6

Syntax: Unsigned32

Read-create Source IPv6 address prefix length.
ruckusIpv6AclFilterSrcOperator

1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.7

Syntax: AclOperator

Read-create

Type of comparison to perform. For now, this only applies to TCP or UDP for comparing the port number.

ruckusIpv6AclFilterSrcPortLow

1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.8

Syntax: Unsigned32

Read-create

Specifies the TCP or UDP port number to match in packets. If the operator is "range", it specifies the start of the range.

ruckusIpv6AclFilterSrcPortHigh

1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.9

Syntax: Unsigned32

Read-create

Used only if the operator is defined as "range", where it specifies the end of the range.

ruckusIpv6AclFilterDestAddr

1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.10

Syntax: InetAddressIPv6

Read-create Destination IPv6 address to match in packets.
ruckusIpv6AclFilterDestPrefixLen

1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.11

Syntax: Unsigned32

Read-create Destination IPv6 address prefix length.
ruckusIpv6AclFilterDestOperator

1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.12

Syntax: AclOperator

Read-create

Type of comparison to perform. For now, this only applies to TCP or UDP for comparing the port number.

ruckusIpv6AclFilterDestPortLow

1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.13

Syntax: Unsigned32

Read-create

Specifies the TCP or UDP port number to match in packets. If the operator is "range", it specifies the start of the range.

ruckusIpv6AclFilterDestPortHigh

1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.14

Syntax: Unsigned32

Read-create

Used only if the operator is defined as "range", where it specifies the end of the range.

ruckusIpv6AclFilterEstablished

1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.15

Syntax: TruthValue

Read-create

Enable or disable the filtering of established TCP packets of which the ACK or RESET flag is on. This filter only applies to the TCP transport protocol.

ruckusIpv6AclFilterIcmpType

1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.16

Syntax: Integer

Read-create

Specifies the ICMPv6 type for matching if the protocol is ICMPv6. The value 0 means to ignore the field.

ruckusIpv6AclFilterIcmpCode

1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.17

Syntax: Integer

Read-create The ICMP Message Code value. Used in combination with ICMP Message Type to set up an ICMP filter. This object is not used with any other protocol. The value 0 means to ignore the field. The supported values are:

Type: Echo reply

Type: Destination unreachable

Type: Echo request

Type: Router advertisement

Type: Router solicitation

Type: Time exceeded

Type: Parameter problem

Type: Timestamp request

ruckusIpv6AclFilterExtIcmpType

1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.18

Syntax: Integer

Read-create

Any type that cannot be specified using the standard types can be specified using this object.

ruckusIpv6AclFilterPolicyName

1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.19

Syntax: AclPolicyName

Read-create Specifies the DSCP value to use in matching or marking.
ruckusIpv6AclFilterDscpMatch

1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.20

Syntax: Integer

Read-create Specifies the DSCP value for matching with this filter.
ruckusIpv6AclFilterDscpForce

1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.21

Syntax: Integer

Read-create

Specifies the DSCP value to be used for marking in outgoing packets matching this filter.

ruckusIpv6AclFilterPriorityMatch

1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.22

Syntax: Integer

Read-create Specifies the 802.1P priority for matching with this filter.
ruckusIpv6AclFilterPriorityForce

1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.23

Syntax: Integer

Read-create

Specifies the 802.1P priority to be used for marking in outgoing packets matching this filter.

ruckusIpv6AclFilterInternalPriority

1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.24

Syntax: Integer

Read-create QoS priority option for this filter.
ruckusIpv6AclFilterFragments

1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.25

Syntax: TruthValue

Read-create

Match IPv6 fragments with non-zero fragment offset in IPv6 packets matching this ACL permit clause.

ruckusIpv6AclFilterSourceRoute

1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.26

Syntax: TruthValue

Read-create Match only source routed packets matching this ACL permit clause.
ruckusIpv6AclFilterMirrorPkts

1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.27

Syntax: TruthValue

Read-create Mirror packets matching ACL permit clause.
ruckusIpv6AclFilterLogEnable

1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.28

Syntax: TruthValue

Read-create Specifies if logging is enabled for the filter.
ruckusIpv6AclFilterComments

1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.29

Syntax: DisplayString

Read-only Remark description of individual Access Control List entry.
ruckusIpv6AclFilterRowStatus

1.3.6.1.4.1.1991.1.1.3.45.1.2.2.1.1.30

Syntax: RowStatus

Read-create

The row status variable is used according to installation and removal conventions for conceptual rows. Setting this object to createAndGo(4) results in the creation of IPv6 ACL filter. Setting this object to destroy(6) removes this IPv6 ACL filter. Other values are ignored.

MAC ACL Filter Table

Name, OID, and syntax Access Description
ruckusMacAclFilterTable

1.3.6.1.4.1.1991.1.1.3.45.1.2.3.1

Not-accessible

Table of Ruckus MAC ACL Filters. MAC ACLs filter traffic based on any of the following fields: source MAC address and source MAC mask, destination MAC address and destination MAC mask, VLAN ID, and Ethertype.

ruckusMacAclFilterEntry

1.3.6.1.4.1.1991.1.1.3.45.1.2.3.1.1

Syntax: RuckusMacAclFilterEntry

Not-accessible An entry in the Ruckus MAC Access Control List Filter table.
ruckusMacAclFilterSeqNum

1.3.6.1.4.1.1991.1.1.3.45.1.2.3.1.1.1

Syntax: Unsigned32

Not-accessible Specifies the sequence number for this ACL filter.
ruckusMacAclFilterAction

1.3.6.1.4.1.1991.1.1.3.45.1.2.3.1.1.2

Syntax: AclAction

Read-create Action to take if the Layer 2 packet matches with this filter.
ruckusMacAclFilterSrcAddr

1.3.6.1.4.1.1991.1.1.3.45.1.2.3.1.1.3

Syntax: MacAddress

Read-create Source MAC address to match in the incoming Layer 2 packet.
ruckusMacAclFilterSrcMask

1.3.6.1.4.1.1991.1.1.3.45.1.2.3.1.1.4

Syntax: MacAddress

Read-create

Source MAC address mask needs to apply with the source address to obtain the MAC address for filter action. For example, to match on the first two bytes of MAC address aabb.ccdd.eeff, the mask should be ffff.0000.0000. Here, the filter matches all source MAC addresses that contain "aabb" as the first two bytes and any values in the remaining address.

ruckusMacAclFilterDestAddr

1.3.6.1.4.1.1991.1.1.3.45.1.2.3.1.1.5

Syntax: MacAddress

Read-create Destination MAC address to match in the incoming Layer 2 packet.
ruckusMacAclFilterDestMask

1.3.6.1.4.1.1991.1.1.3.45.1.2.3.1.1.6

Syntax: MacAddress

Read-create

Destination MAC address mask needs to apply with the destination address to obtain the MAC address for filter action. For example, to match on the first two bytes of MAC address aabb.ccdd.eeff, the mask should be ffff.0000.0000. Here, the filter matches all source MACs that contain "aabb" as the first two bytes and any values in the remaining address.

ruckusMacAclFilterEtherType

1.3.6.1.4.1.1991.1.1.3.45.1.2.3.1.1.7

Syntax: Integer

Read-create

EtherType to match in the incoming packet. The extended option enables the definition of other types using the OID ruckusMacAclFilterExtEtherType which takes any value.

ruckusMacAclFilterExtEtherType

1.3.6.1.4.1.1991.1.1.3.45.1.2.3.1.1.8

Syntax: EtherType

Read-create

Any EtherType other than standard protocols mentioned with ruckusMacAclFilterEtherType OID. The value 0 means any protocol.

ruckusMacAclFilterMirrorPkts

1.3.6.1.4.1.1991.1.1.3.45.1.2.3.1.1.9

Syntax: TruthValue

Read-create Mirror packets matching ACL permit clause.
ruckusMacAclFilterLogEnable

1.3.6.1.4.1.1991.1.1.3.45.1.2.3.1.1.10

Syntax: TruthValue

Read-create Specifies if logging is enabled for this filter.
ruckusMacAclFilterRowStatus

1.3.6.1.4.1.1991.1.1.3.45.1.2.3.1.1.11

Syntax: RowStatus

Read-create

The row status variable is used according to installation and removal conventions for conceptual rows. Setting this object to createAndGo(4) results in the creation of MAC ACL filter. Setting this object to destroy(6) removed this MAC ACL filter. Other values are ignored.

ACL port bind table

Name, OID, and syntax Access Description
ruckusAclBindings

1.3.6.1.4.1.1991.1.1.3.45.1.3

Not-accessible Defines the ACL bindings.
ruckusAclIfBindTable

1.3.6.1.4.1.1991.1.1.3.45.1.3.1

Not-accessible Table of IPv4 or IPv6 or MAC ACL bindings to a port.
ruckusAclIfBindEntry

1.3.6.1.4.1.1991.1.1.3.45.1.3.1.1

Syntax: RuckusAclIfBindEntry

Not-accessible An entry in the IPv4 or IPv6 or MAC ACL bindings for a given port.
ruckusAclIfBindPort

1.3.6.1.4.1.1991.1.1.3.45.1.3.1.1.1

Syntax: InterfaceIndex

Not-accessible The port where this ACL binding is applied.
ruckusAclIfBindType

1.3.6.1.4.1.1991.1.1.3.45.1.3.1.1.2

Syntax: AclType

Not-accessible Type of the ACL this binding explains on the port.
ruckusAclIfBindDirection

1.3.6.1.4.1.1991.1.1.3.45.1.3.1.1.3

Syntax: AclDirection

Not-accessible Direction in which this ACL is applied on the port.
ruckusAclIfBindName

1.3.6.1.4.1.1991.1.1.3.45.1.3.1.1.4

Syntax: AclName

Read-create Defined ACL name to bind on the port in the given direction.
ruckusAclIfBindLog

1.3.6.1.4.1.1991.1.1.3.45.1.3.1.1.5

Syntax: TruthValue

Read-create Enable or disable logging on the port for this ACL.
ruckusAclIfBindRowStatus

1.3.6.1.4.1.1991.1.1.3.45.1.3.1.1.6

Syntax: RowStatus

Read-create

The row status variable is used according to installation and removal conventions for conceptual rows. Setting this object to createAndGo(4) results in the binding of IPv4 or IPv6 or MAC ACL with a given port. Setting this object to destroy(6) unbinds this IPv4 or IPv6 or MAC ACL from the port. Other values are ignored.

ACL VLAN bind table

Name, OID, and syntax Access Description
ruckusAclVlanBindTable

1.3.6.1.4.1.1991.1.1.3.45.1.3.2

Not-accessible Table of IPv4 or IPv6 or MAC ACL bindings to a VLAN.
ruckusAclVlanBindEntry

1.3.6.1.4.1.1991.1.1.3.45.1.3.2.1

Syntax: RuckusAclVlanBindEntry

Not-accessible An entry in the IPv4 or IPv6 or MAC ACL bindings for a given VLAN.
ruckusAclVlanBindId

1.3.6.1.4.1.1991.1.1.3.45.1.3.2.1.1

Syntax: VlanId

Not-accessible The VLAN where this ACL binding is applied.
ruckusAclVlanBindType

1.3.6.1.4.1.1991.1.1.3.45.1.3.2.1.2

Syntax: AclType

Not-accessible Type of the ACL this binding explains on the VLAN.
ruckusAclVlanBindDirection

1.3.6.1.4.1.1991.1.1.3.45.1.3.2.1.3

Syntax: AclDirection

Not-accessible Direction in which this ACL is applied on the VLAN.
ruckusAclVlanBindName

1.3.6.1.4.1.1991.1.1.3.45.1.3.2.1.4

Syntax: AclName

Read-create Defined ACL name to bind on the VLAN in the given direction.
ruckusAclVlanBindLog

1.3.6.1.4.1.1991.1.1.3.45.1.3.2.1.5

Syntax: TruthValue

Read-create Enable or disable logging on the VLAN for this ACL.
ruckusAclVlanBindRowStatus

1.3.6.1.4.1.1991.1.1.3.45.1.3.2.1.6

Syntax: RowStatus

Read-create

The row status variable is used according to installation and removal conventions for conceptual rows. Setting this object to createAndGo(4) results in the binding of IPv4 or IPv6 or MAC ACL with a given VLAN. Setting this object to destroy(6) unbinds this IPv4 or IPv6 or MAC ACL from the VLAN. Other values are ignored.

ACL VLAN Port (Vport) Bind Table

Name, OID, and syntax Access Description
ruckusAclVPortBindTable

1.3.6.1.4.1.1991.1.1.3.45.1.3.3

Not-accessible Table of IPv4 or IPv6 or MAC ACL bindings to a port on the VLAN.
ruckusAclVPortBindEntry

1.3.6.1.4.1.1991.1.1.3.45.1.3.3.1

Syntax: RuckusAclVPortBindEntry

Not-accessible An entry in the IPv4 or IPv6 or MAC ACL bindings for a port in a VLAN.
ruckusAclVPortBindId

1.3.6.1.4.1.1991.1.1.3.45.1.3.3.1.1

Syntax: VlanId

Not-accessible The VLAN where this ACL binding is applied.
ruckusAclVPortBindPort

1.3.6.1.4.1.1991.1.1.3.45.1.3.3.1.2

Syntax: InterfaceIndex

Not-accessible The port in the VLAN where this ACL binding is applied.
ruckusAclVPortBindType

1.3.6.1.4.1.1991.1.1.3.45.1.3.3.1.3

Syntax: AclType

Not-accessible The type of ACL binding applied to the port in a VLAN.
ruckusAclVPortBindDirection

1.3.6.1.4.1.1991.1.1.3.45.1.3.3.1.4

Syntax: AclDirection

Not-accessible The packet flow direction on the VLAN port interface where the ACL is applied.
ruckusAclVPortBindName

1.3.6.1.4.1.1991.1.1.3.45.1.3.3.1.5

Syntax: AclName

Read-create Defined ACL name to bind on the port in a VLAN.
ruckusAclVPortBindLog

1.3.6.1.4.1.1991.1.1.3.45.1.3.3.1.6

Syntax: TruthValue

Read-create Enable or disable logging on the port in a VLAN for this ACL.
ruckusAclVPortBindRowStatus

1.3.6.1.4.1.1991.1.1.3.45.1.3.3.1.7

Syntax: RowStatus

Read-create

The row status variable is used according to installation and removal conventions for conceptual rows. Setting this object to createAndGo(4) results in the binding of IPv4 or IPv6 or MAC ACL on a port in a given VLAN. Setting this object to destroy(6) unbinds this IPv4 or IPv6 or MAC ACL from the port in the given VLAN. Other values are ignored.

ACL on CPU Port Bind Table

Name, OID, and syntax Access Description
ruckusAclOnCpuIfBindTable

1.3.6.1.4.1.1991.1.1.3.45.1.3.4

Syntax: Sequence of RuckusAclOnCpuIfBindEntry

 Not-accessible Table of bindings for IPv4, IPv6, or MAC ACLs to a CPU port.
ruckusAclOnCpuIfBindEntry

1.3.6.1.4.1.1991.1.1.3.45.1.3.4.1

Syntax: RuckusAclOnCpuIfBindEntry

 Not-accessible An entry in the IPv4, IPv6, or MAC ACL bindings table for a specific ACL on the CPU port.
ruckusAclOnCpuIfBindType

1.3.6.1.4.1.1991.1.1.3.45.1.3.4.1.1

Syntax: AclType

 Not-accessible The type of ACL described here refers to the binding on the CPU port.

ruckusAclOnCpuIfBindDirection

1.3.6.1.4.1.1991.1.1.3.45.1.3.4.1.2

Syntax: AclDirection

 Read-only The packet flow direction on the CPU port where the ACL is applied.

ruckusAclOnCpuIfBindName

1.3.6.1.4.1.1991.1.1.3.45.1.3.4.1.3

Syntax: AclName

 Read-only Defines the ACL name to bind to the CPU port.

ACL MIB Conformance

Name, OID, and syntax Access Description
ruckusAclConformance

1.3.6.1.4.1.1991.1.1.3.45.2

Not-accessible The MIB module that gives the conformance information.
ruckusAclCompliance

1.3.6.1.4.1.1991.1.1.3.45.2.1

Not-accessible

The compliance statement for entities which implement RUCKUS-ACL-MIB.

ruckusAclGroup

1.3.6.1.4.1.1991.1.1.3.45.2.2.1

Not-accessible A collection of objects that provide ACL information on a given unit.
Parent topic: RUCKUS-ACL-MIB