Port VLAN configuration table

Note: The snVLanByPortTable object was deprecated. Use VLanByPortCfgTable instead of snVLanByPortTable.

Name, OID, and syntax

Access

Description

snVLanByPortCfgTable

brcdIp.1.1.3.2.7

None

The Port VLAN (Layer 2 VLAN) configuration table.

snVLanByPortCfgEntry

brcdIp.1.1.3.2.7.1

None

An entry of the port VLAN configuration table.

snVLanByPortCfgVLanId

brcdIp.1.1.3.2.7.1.1

Syntax: Integer

Read-only

The VLAN ID index to this table. Each VLAN identifier can be a member of multiple ports.

Valid values: 1 - 4095

snVLanByPortCfgQos

brcdIp.1.1.3.2.7.1.2

Syntax: PortQosTC

Read-write

Shows the Quality of Service (QoS) settings for the devices.

For Stackable devices, the values can be one of the following:

  • level0(0) - Low priority
  • level1(1) - High priority

For Chassis devices, the value can be one of the following:

  • level0(0)
  • level1(1)
  • level2(2)
  • level3(3)
  • level4(4)
  • level5(5)
  • level6(6)
  • level7(7)
snVLanByPortCfgStpMode

brcdIp.1.1.3.2.7.1.3

Syntax: Integer

Read-write

Indicates whether or not Spanning Tree Protocol (STP) is enabled:

  • disabled(0)
  • enabled(1)

The following values are supported on FastIron SuperX software releases:

  • disabled(0)
  • enableStp(1)
  • enableRstp(2)
snVLanByPortCfgStpPriority

brcdIp.1.1.3.2.7.1.4

Syntax: Integer

Read-write

Shows the value of the dot1dStpPriority, which is the first two octets of the STP or RSTP bridge ID. The STP and RSTP bridge IDs are eight octets long. This object contains the writable portion of the bridge ID.

Valid values: 1 - 65535

snVLanByPortCfgStpGroupMaxAge

brcdIp.1.1.3.2.7.1.5

Syntax: Integer32

Read-write

Shows the value of dot1dStpBridgeMaxAge, which is the last six octets or the STP or RSTP bridge ID. All bridges use this object for MaxAge when this bridge is acting as the root.

Note: 802.1D-1990 specifies that the range for this parameter is related to the value of dot1dStpBridgeHelloTime object. The granularity of this timer is specified by 802.1D-1990 to be one second. An agent may return a bad value error if a set is attempted to a value which is not a whole number of seconds. (Refer to RFC 1493 Bridge MIB.)

Valid values: 6 - 40

snVLanByPortCfgStpGroupHelloTime

brcdIp.1.1.3.2.7.1.6

Syntax: Integer

Read-write

Shows the value of dot1dStpBridgeHelloTime, which is the value used by all bridges when this bridge is acting as the root.

Note: The granularity of this timer is specified by 802.1D-1990 to be one second. An agent may return a bad Value error if a set is attempted to a value which is not a whole number of seconds. (Refer to RFC 1493 Bridge MIB.)

Valid values: 1 - 10

snVLanByPortCfgStpGroupForwardDelay

brcdIp.1.1.3.2.7.1.7

Syntax: Integer32

Read-write

Shows the value of dot1dStpBridgeForwardDelay, which is the value used by all bridges for ForwardDelay when this bridge is acting as the root.

Note: 802.1D-1990 specifies that the range for this parameter is related to the value of dot1dStpBridgeMaxAge object. The granularity of this timer is specified by 802.1D-1990 to be one second. An agent may return a bad value error if a set is attempted to a value which is not a whole number of seconds. (Refer to RFC 1493 Bridge MIB.)

Valid values: 2 - 30

snVLanByPortCfgBaseNumPorts

brcdIp.1.1.3.2.7.1.8

Syntax: Integer32

Read-only

The number of ports controlled by this bridging entity.

snVLanByPortCfgBaseType

brcdIp.1.1.3.2.7.1.9

Syntax: Integer

Read-only

Indicates what type of bridging this bridge can perform. If a bridge is actually performing a certain type of bridging, this will be indicated by entries in the port table for the given type:

  • unknown(1)
  • transparentOnly(2)
  • sourcerouteOnly(3)
  • srt(4)
snVLanByPortCfgStpProtocolSpecification

brcdIp.1.1.3.2.7.1.10

Syntax: Integer

Read-only

Shows what version of STP is being run:

  • unknown(1)
  • decLb100(2) - Indicates the DEC LANbridge 100 Spanning Tree Protocol.
  • ieee8021d(3) - IEEE 802.1d implementations will return this value. If future versions of the IEEE Spanning Tree Protocol are released that are incompatible with the current version, a new value will be defined.
snVLanByPortCfgStpMaxAge

brcdIp.1.1.3.2.7.1.11

Syntax: Integer

Read-only

Shows the value of dot1dStpMaxAge, which is the maximum age that the STP information can exist before it is discarded. The STP information is learned from the network. The value of this object is in hundredths of a second, and is the actual value that this bridge is currently using.

(Refer to RFC 1493 Bridge MIB.)

snVLanByPortCfgStpHelloTime

brcdIp.1.1.3.2.7.1.12

Syntax: Timeout

Read-only

Shows the value of dot1dStpHelloTime, which is the interval between the transmission of configuration bridge PDUs by this node. This value applies to any port when it is the root of the spanning tree or is trying to become the root. This is the actual value that this bridge is currently using.

This value is in hundredths of a second.

(Refer to RFC 1493 Bridge MIB.)

snVLanByPortCfgStpHoldTime

brcdIp.1.1.3.2.7.1.13

Syntax: Integer32

Read-only

Shows the value of dot1dStpHoldTime, which is the interval when no more than two configuration bridge PDUs can be transmitted by this node. The interval is in units of hundredths of a second.

(Refer to RFC 1493 Bridge MIB.)

snVLanByPortCfgStpForwardDelay

brcdIp.1.1.3.2.7.1.14

Syntax: Timeout

Read-only

Shows the value of dot1dStpForwardDelay, which controls how fast a port changes its spanning state when moving towards the forwarding state. The value determines how long the port stays in each of the listening and learning states, which precede the forwarding state. This value is also used, when a topology change has been detected and is under way, to age all dynamic entries in the forwarding database.

Note: This value is the one that this bridge is currently using in contrast to dot1dStpBridgeForwardDelay, which is the value that this bridge and all others would start using should this bridge become the root.This value is measured in hundredths of a second. (Refer to RFC 1493 Bridge MIB.)
snVLanByPortCfgStpTimeSinceTopologyChange

brcdIp.1.1.3.2.7.1.15

Syntax: Time ticks

Read-only

Shows the time since the last topology change was detected by the bridge entity. This time is in hundredths of a second.

snVLanByPortCfgStpTopChanges

brcdIp.1.1.3.2.7.1.16

Syntax: Counter32

Read-only

Shows the total number of topology changes detected by this bridge since the management entity was last reset or initialized.

snVLanByPortCfgStpRootCost

brcdIp.1.1.3.2.7.1.17

Syntax: Integer32

Read-only

Shows the value of dot1dStpRootCost, which is the cost of the path to the root as seen from this bridge.

(Refer to RFC 1493 Bridge MIB.)

snVLanByPortCfgStpRootPort

brcdIp.1.1.3.2.7.1.18

Syntax: Integer32

Read-only

Shows the value of dot1dStpRootPort, which is the port number of the port which offers the lowest cost path from this bridge to the root bridge.

(Refer to RFC 1493 Bridge MIB.)

snVLanByPortCfgStpDesignatedRoot

brcdIp.1.1.3.2.7.1.19

Syntax: BridgeId

Read-only

Shows the value of dot1dStpDesignatedRoot, which is the bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the root identifier parameter in all configuration bridge PDUs originated by this node.

(Refer to RFC 1493 Bridge MIB.)

snVLanByPortCfgBaseBridgeAddress

brcdIp.1.1.3.2.7.1.20

Syntax: MAC address

Read-only

Shows the MAC address used by this bridge when it must be referred to in a unique fashion. It is recommended that this be the numerically smallest MAC address of all ports that belong to this bridge; however, it is only required to be unique. When concatenated with dot1dStpPriority, a unique bridge identifier is formed, which is used in the Spanning Tree Protocol.

snVLanByPortCfgVLanName

brcdIp.1.1.3.2.7.1.21

Syntax: DisplayString

Read-write

Shows the name of the VLAN community string.

Valid values: Up to 32 characters

snVLanByPortCfgRouterIntf

brcdIp.1.1.3.2.7.1.22

Syntax: Integer32

Read-write

This object is optional. It identifies the virtual interface for the router to the VLAN, and applies only to the router. If an SNMP-Get value is zero, that means this object was not configured.

snVLanByPortCfgRowStatus

brcdIp.1.1.3.2.7.1.23

Syntax: Integer

Read-write

Deletes a VLAN entry. Delete(3).
snVLanByPortCfgStpVersion

brcdIp.1.1.3.2.7.1.24

Syntax: Integer

Note: This object is supported only on the FastIron SuperX devices.

Read-write

Shows the version of Spanning Tree Protocol the bridge is currently running:

  • stpCompatible(0) - STP (IEEE 802.1D)
  • rstp(2) - RSTP (IEEE 802.1w)
snVLanByPortCfgMcastMode

brcdIp.1.1.3.2.7.1.26

Syntax: Integer

Read-write

Multicast (IGMP snooping) mode on the VLAN can be set as either active or passive or disabled. The default is disabled.

  • disabled(0): P Multicast is disabled on this VLAN
  • active(1): this VLAN generates IGMP queries
  • passive(2): this VLAN listens for IGMP packets

Default: disabled(0)

snVLanByPortCfgMcastVersion

brcdIp.1.1.3.2.7.1.27

Syntax: Integer32

Read-write

Specifies version of Multicast on this VLAN.

Values are 2 or 3.

The default is 2. The initial value is 0.

Parent topic: VLAN Layer 2 Switch MIB Definition