IP prefix list table
An IP prefix list specifies a list of networks. When you apply an IP prefix list to a neighbor, the Layer 3 Switch sends or receives only a route whose destination is in the IP prefix list. You can configure up to 100 prefix lists. The software interprets the prefix lists in sequential order, beginning with the lowest sequence number.
Name, OID, and Syntax |
Access |
Description |
|---|---|---|
| snIpPrefixListTable
brcdIp.1.2.2.14 |
None |
IP prefix list table. |
| snIpPrefixListEntry brcdIp.1.2.2.14.1 Syntax: SnIpPrefixListEntry |
None | An entry in the IP Prefix List table. |
| snIpPrefixListName
brcdIp.1.2.2.14.1.1 Syntax: Octet String |
Read-only |
Specifies the name of the prefix list. This name can be used when applying the prefix list to a neighbor. It is an octet string; each character of the name is represented by one octet. There can be up to 32 octets for this name. |
| snIpPrefixListSequence
brcdIp.1.2.2.14.1.2 Syntax: Integer32 |
Read-only |
Shows the sequence of an entry in the table. There can be up to 100 prefix list entries. If a sequence number is not specified, then entries are numbered in increments of 5, beginning with prefix list entry 5. Incoming or outgoing routes are matched against the entries in the IP prefix list in numerical order, beginning with the lowest sequence number. |
| snIpPrefixListDesc
brcdIp.1.2.2.14.1.3 Syntax: Octet String |
Read-write |
Specifies the description of the prefix. This description is in an octet string; each character in the description is represented by one octet. There can be up to 80 octets in the description. |
| snIpPrefixListAction
brcdIp.1.2.2.14.1.4 Syntax: Integer |
Read-write |
Indicates what to do with the route if it matches this entry: |
| snIpPrefixListAddr
brcdIp.1.2.2.14.1.5 Syntax: IpAddress |
Read-write |
Shows the IP address of the prefix. |
| snIpPrefixListMask
brcdIp.1.2.2.14.1.6 Syntax: IpAddress |
Read-write |
Shows the number of bits in the prefix network mask. |
| snIpPrefixListGeValue
brcdIp.1.2.2.14.1.7 Syntax: Integer |
Read-write |
Specifies that the prefix is greater than the value of the IP prefix list table object. Valid values: 0 - 32 |
| snIpPrefixListLeValue
brcdIp.1.2.2.14.1.8 Syntax: Integer |
Read-write |
Specifies that the prefix is less than the value of the IP prefix list table object. Valid values: 0 - 32 |
|
Note: You can specify a range of length for prefixes that are more specific than the values
for the
IP prefix list table and
IP prefix list table objects. The
ge-value or
le-value you specify must meet the following condition:length < ge-value <= le-value <= 32
If a value for IP prefix list table is specified, then the mask-length range is from the value of IP prefix list table to 32. If a value for IP prefix list table is specified, then mask-length range is from length to the value of IP prefix list table. If no value is specified for either the less than or greater than objects, then routes must exactly match the prefixes on the list. |
||
| snIpPrefixListRowStatus
brcdIp.1.2.2.14.1.9 Syntax: Integer |
Read-write |
Controls the management of the table rows. The values that can be written are: If the row exists, then a SET with a value of create(4) returns a "bad value" error. Deleted rows are removed from the table immediately. The following values can be returned on reads: |