show inline power detail

Displays detailed information about the PoE power supplies installed in a PoE device.
Syntax
show inline power detail [ stack-unit | debug-info stack-unit ]
Parameters
stack-unit
Displays detailed inline power information for the specified stack unit.
debug-info
Displays detailed debug information.
Modes

User EXEC mode

Usage Guidelines

You can view the PoE operational status for the entire device, for a specific PoE module, or for a specific interface.

The show inline power detail command displays the following information.

Output field Description
Max Curr: The number of milliwatts available for the unit in the stack, not the entire stack. This value is either the default or configured maximum power level, or the power class that was automatically detected by the device.
Voltage The number of Volts allocated to the stack.
Capacity The total PoE power supply capacity and the amount of available power (current free) for PoE-power-consuming devices. Both values are shown in milliwatts.
Firmware Version Returns firmware version information.
Hardware Version Returns hardware version information.
Power Allocations The number of times the device fulfilled PoE requests for power.
Cumulative Port State Data Shows the number of ports with a particular status/configuration.
Cumulative Port Power Data Shows the port power consumption and allocation.
Device Status The status of the device:
  • Failed: No (bad or unreachable) PoE device found (bootup time)
  • Good: OK - Expected PoE device Found (Zone1, no VOP)
  • Revived: Device is currently refreshed
  • n/a: Reserved
  • Lost: Device lost or different from expected (while in operation)
  • VOP-Sev1: Device error 1 (Zone2, VOP severity 1)
  • VOP-Sev2: Device error 1 (Zone2, VOP severity 2)
  • VOP-Sev3: Device error 1 (Zone2, VOP severity 3)
  • VmErr: Device Vmain Error
  • Vm2vErr: Device Vmain < System AVG Vmain by 2v or more
  • Recovered: OK - Expected PoE device Found (Zone3, recovered from VOP)
Examples

The following is an example of show inline power detail command output for an ICX 7150 device. 

device# show inline power detail
Power Supply Data On unit 1:
++++++++++++++++++
Power Supply Data:
++++++++++++++++++

power supply 1 is not present 
Power Supply #2:
        Max Curr:       13.8 Amps
        Voltage:        54.0 Volts
        Capacity:       748 Watts


POE Details Info. On Unit 1 : 


General PoE Data:
+++++++++++++++++

Firmware                                                          
Version                                                           
----------------
01.6.7 Build 013

Hardware
Version
-----------------
V1R3

Cumulative Port State Data:
+++++++++++++++++++++++++++

#Ports    #Ports     #Ports   #Ports    #Ports       #Ports     #Ports
Admin-On  Admin-Off  Oper-On  Oper-Off  Off-Denied   Off-No-PD  Off-Fault
-------------------------------------------------------------------------
30        2          7        25        0            23         2 
Cumulative Port Power Data:
+++++++++++++++++++++++++++

#Ports  #Ports  #Ports        Power       Power
Pri: 1  Pri: 2  Pri: 3  Consumption  Allocation
-----------------------------------------------
1       0       29         43.900 W   470.000 W

The following example shows sample output from the show inline power detail command, including information about the device status, when the debug-info keyword is used. 

device> show inline power detail debug-info

Power Supply Data On unit 1:
++++++++++++++++++
 
Power Supply Data:
++++++++++++++++++
power supply 1 is not present
Power Supply #2:
        Max Curr:       13.9 Amps
        Voltage:        54.0 Volts
        Capacity:       748 Watts
        PoePower:       748 Watts

POE Details Info. On Unit 1 :

General PoE Data:
+++++++++++++++++
                                                                  
Firmware
Version
----------------
02.1.1 Build 002
Hardware
Version
----------------
V2R2
Note: Number of PoE Devices:9. This number of LSBs should be zero
                 in devFaultMap, devTempOff,devTempAlarm
First System Status:
                cpuStatus1 (fwDnldReq:0, errController:0), cpuStatus2(errMemory:0),
                factoryDefault:1, genInternalErr:0, privateLabel:0, userByte:ff,
                devFaultMap:0, devTempOff: 0, devTempAlarm: 0, intReg:2f2c
Latest System Status:
                cpuStatus1 (fwDnldReq:0, errController:0), cpuStatus2(errMemory:0),
                factoryDefault:0, genInternalErr:0, privateLabel:0, userByte:0,
                devFaultMap:0, devTempOff: 0, devTempAlarm: 0, intReg:2f2c
Device HW version         : 0:V2R2      1:V2R2      2:V2R2      3:V2R2      4:V2R2      5:V2R2      6:V2R2      7:V2R2      8:V2R2      
Device Temperature(deg-C) : 0:40        1:40        2:42        3:44        4:48        5:48        6:46        7:46        8:44        
Device Status             : 0:Good      1:Good      2:Good      3:Good      4:VOP-Sev1  5:VOP-Sev1  6:Good      7:Good      8:Good      
 
Cumulative Port State Data:
+++++++++++++++++++++++++++
#Ports    #Ports     #Ports   #Ports    #Ports       #Ports     #Ports
Admin-On  Admin-Off  Oper-On  Oper-Off  Off-Denied   Off-No-PD  Off-Fault
-------------------------------------------------------------------------
48        0          10       38        0            38         0        
 
Cumulative Port Power Data:
+++++++++++++++++++++++++++
#Ports  #Ports  #Ports        Power       Power
Pri: 1  Pri: 2  Pri: 3  Consumption  Allocation
-----------------------------------------------
0       0       48         42.700 W   507.515 W
                                                                  
 
Power Supply Data On unit 6:
++++++++++++++++++
 
Power Supply Data:
++++++++++++++++++
Power Supply #1:
        Max Curr:       13.9 Amps
        Voltage:        54.0 Volts
        Capacity:       748 Watts
        PoePower:       748 Watts
power supply 2 is not present

POE Details Info. On Unit 6 :

General PoE Data:                                                 
+++++++++++++++++
Firmware
Version
----------------
02.1.1 Build 002
Hardware
Version
----------------
V2R4
Note: Number of PoE Devices:9. This number of LSBs should be zero
                 in devFaultMap, devTempOff,devTempAlarm
First System Status:
                cpuStatus1 (fwDnldReq:0, errController:0), cpuStatus2(errMemory:0),
                factoryDefault:1, genInternalErr:0, privateLabel:0, userByte:ff,
                devFaultMap:0, devTempOff: 0, devTempAlarm: 0, intReg:3304
Latest System Status:
                cpuStatus1 (fwDnldReq:0, errController:0), cpuStatus2(errMemory:0),
                factoryDefault:0, genInternalErr:0, privateLabel:0, userByte:0,
                devFaultMap:0, devTempOff: 0, devTempAlarm: 0, intReg:3304
Device HW version         : 0:V2R4      1:V2R4      2:V2R4      3:V2R4      4:V2R4      5:V2R4      6:V2R4      7:V2R4      8:V2R4      
Device Temperature(deg-C) : 0:42        1:40        2:42        3:44        4:42        5:46        6:40        7:44        8:40        
Device Status             : 0:Good      1:Good      2:Good      3:Good      4:Good      5:Good      6:Good      7:Good      8:Good      
 
Cumulative Port State Data:
+++++++++++++++++++++++++++
#Ports    #Ports     #Ports   #Ports    #Ports       #Ports     #Ports
Admin-On  Admin-Off  Oper-On  Oper-Off  Off-Denied   Off-No-PD  Off-Fault
-------------------------------------------------------------------------
48        0          11       37        0            36         0        
 
Cumulative Port Power Data:
+++++++++++++++++++++++++++
#Ports  #Ports  #Ports        Power       Power
Pri: 1  Pri: 2  Pri: 3  Consumption  Allocation
-----------------------------------------------                   
0       0       48         46.700 W   445.435 W
History
Release version Command history
08.0.10 This command was introduced.
08.0.50 Added the debug-info option.
08.0.60 The output field included Hardware Version.
08.0.70d Information on device status was added to the command output.
08.0.80e Information on device status was added to the command output.
Parent topic: Show Commands