Commands C

In this section:

1. cable-signal-error-scan
   Sets the cable signal error scan interval for 2.5G ports.
2. capability as4
   Enables 4-byte autonomous system number (ASN) capability at the BGP global level.
3. captive-portal
   Creates a user-defined Captive Portal profile.
4. captive-portal profile
   Applies a configured Captive Portal profile on a Web Authentication-enabled VLAN.
5. ccep-up-delay
   In an MCT configuration, places client cluster edge port (CCEP) dynamic LAGs in a blocking state for the specified time while Client Cluster Protocol (CCP) comes up. This allows for better traffic convergence.
6. cdp enable
   Enables Cisco Discovery Protocol (CDP) at the interface level.
7. cdp run
   Enables the device to intercept and display Cisco Discovery Protocol (CDP) messages.
8. cfg-archive management archive-size
   Changes the size of the archive.

   FI 09.0.10d Per FI-256961, hide this command
9. cfg-archive management compare-archives
   Compares two archives and shows the differences between them.
10. cfg-archive management compare-running-config
    Compares an archive with the running configuration.
11. cfg-archive management compare-startup-config
    Compares an archive with the startup configuration.
12. cfg-archive management copy
    Enables the ability to copy a file to an archive, or an archive to another archive.
13. cfg-archive management copy-running-config
    Copies the running configuration to an archive.
14. cfg-archive management delete
    Deletes a specified archive or all archives.
15. cfg-archive management delete-unsaved-cfg
    Deletes an unsaved running configuration after a system reload.
16. cfg-archive management list
    Lists all archive names in the repository.
17. cfg-archive management reload-with-archive
    Enables the ability to reload the system with a specific archive without changing the startup configuration.
18. cfg-archive management rename
    Enables the ability to rename an existing archive.
19. cfg-archive management show-archive-content
    Displays the content of an archive.
20. cfg-archive management show-current-config
    Displays the current running configuration.
21. cfg-archive management show-unsaved-cfg
    Displays the unsaved running configuration before the last system reload.
22. cfg-archive revert
    Enables or disables configuration archive auto-revert.
23. cfg-archive revert-option
    Configures configuration archive auto-revert options.
24. chassis fanless
    Enables chassis fanless mode that sets the device to operate with the fan disabled while limiting the PoE budget to 150 Watts or less.
25. chassis led off
    Turns off chassis LEDs on RUCKUS ICX 8200 devices.
26. chassis name
    Configures a chassis name.
27. chassis poll-time
    Configures the interval at which the system polls the chassis for status updates.
28. clear 802-1w statistics
    Clear the Rapid Spanning Tree Protocol (RSTP) (802.1W) statistics for the specified VLAN.
29. clear access-list
    Clears ACL counters.
30. clear access-list accounting
    Clears access control list (ACL) accounting statistics for IPv4 ACLs, IPv6 ACLs, and Layer 2 MAC filters.
31. clear acl-on-arp
    Clears the count of how many ARP packets have been dropped on the interface.
32. clear arp
    Removes entries from the Address Resolution Protocol (ARP) table.
33. clear authentication sessions
    Clears 801.1X and MAC authentication sessions on an interface or a range of interfaces.
34. clear authentication statistics
    Clears 802.1X and MAC authentication sessions and statistics on an interface or range of interfaces.
35. clear cable-diagnostics tdr
    Clears the results of Virtual Cable Test (VCT) Time Domain Reflectometry (TDR) testing conducted on a port.
36. clear chassis unit-id
    Resets the LED warning light for a power supply after a temporary power fluctuation.
37. clear cli-command-history
    Clears the allocated logging memory and removes the command log history.
38. clear dhcp
    Clears the DHCP binding database.
39. clear dlogger logs
    Clears distributed logger logs and filter configurations.
40. clear dot1x sessions
    Clears 802.1X authentication sessions.
41. clear dot1x statistics
    Clears 802.1X authentication statistics.
42. clear dot1x-mka statistics
    Clears current MACsec Key Agreement (MKA) statistics.
43. clear fdp counters
    Clears Foundry Discovery Protocol (FDP) and Cisco Discovery Protocol (CDP) statistics.
44. clear fdp table
    Clears the information received in Foundry Discovery Protocol (FDP) and Cisco Discovery Protocol (CDP) updates from neighboring devices.
45. clear ikev2 sa
    Clears Internet Key Exchange version 2 security associations (IKEv2 SAs).
46. clear ikev2 statistics
    Clears Internet Key Exchange version 2 (IKEv2) statistics by resetting the various IKEv2 counters to zero.
47. clear ip bgp dampening
    Reactivates suppressed BGP4 routes.
48. clear ip bgp flap-statistics
    Clears the dampening statistics for a BGP4 route without changing the dampening status of the route.
49. clear ip bgp local routes
    Clears BGP4 local routes from the IP route table and resets the routes.
50. clear ip bgp neighbor
    Requests a dynamic refresh of BGP4 connections or routes from a neighbor, with a variety of options.
51. clear ip bgp routes
    Clears BGP4 routes from the IP route table and resets the routes.
52. clear ip bgp traffic
    Clears the BGP4 message counter for all neighbors.
53. clear ip bgp vrf
    Clears BGP4 information for a virtual routing and forwarding (VRF) instance.
54. clear ip dhcp-server binding
    Clears the leases from the lease binding database.
55. clear ip dhcp-server statistics
    Resets all DHCP server packet statistics, or server packet statistics for a specified pool.
56. clear ip dns vrf
    Clears the DNS cache for the configured VRF.
57. clear ip igmp cache
    Clears the IGMP group membership table from a VRF instance or from all interfaces on the device.
58. clear ip igmp traffic
    Clears statistics for IGMP traffic from a VRF instance or from all interfaces on the device.
59. clear ip mroute
    Removes multicast routes from the IP multicast routing table .
60. clear ip msdp peer
    Clears multicast source discovery protocol (MSDP) peer information.
61. clear ip msdp sa-cache
    Clears the multicast source discovery protocol (MSDP) source active (SA) cache.
62. clear ip msdp statistics
    Clears multicast source discovery protocol (MSDP) statistics.
63. clear ip multicast counters
    Clears IGMP snooping on error and traffic counters for all VLANs.
64. clear ip multicast mcache
    Clears the multicast forwarding mcache for all VLANs.
65. clear ip multicast vlan
    Clears traffic counters on a specified VLAN.
66. clear ip ospf
    Clears OSPF process, counters, neighbors, or routes.
67. clear ip pim cache
    Clears the PIM forwarding cache on a specific VRF instance or on all VRFs.
68. clear ip pim counters
    Clears PIM message counters.
69. clear ip pim hw-resource
    Clears the PIM hardware resource fail count for a specific VRF instance or for all VRFs.
70. clear ip pim rp-map
    Updates the entries in the static multicast forwarding table for a specific VRF instance or for all VRFs.
71. clear ip pim traffic
    Clears PIM traffic for a specific VRF instance or on all VRFs.
72. clear ip pimsm-snoop
    Clears PIM sparse mode (SM) information.
73. clear ip route
    Clears entire IP route table or specific routes.
74. clear ip tunnel
    Clears statistics (reset all fields to zero) for all IP tunnels or for a specific tunnel interface.
75. clear ip vrrp statistics
    Clears IPv4 Virtual Router Redundancy Protocol (VRRP) statistics.
76. clear ip vrrp-extended statistics
    Clears IPv4 Virtual Router Redundancy Protocol (VRRP) Extended (VRRP-E) statistics.
77. clear ipsec sa
    Clears IPsec security associations (SAs).
78. clear ipv6 bgp dampening
    Reactivates suppressed BGP4+ routes.
79. clear ipv6 bgp flap-statistics
    Clears the dampening statistics for a BGP4+ route without changing the dampening status of the route.
80. clear ipv6 bgp local routes
    Clears BGP4+ local routes from the IP route table and resets the routes.
81. clear ipv6 bgp neighbor
    Requests a dynamic refresh of BGP4+ connections or routes from a neighbor, with a variety of options.
82. clear ipv6 bgp routes
    Clears BGP4+ routes from the route table and resets the routes.
83. clear ipv6 bgp traffic
    Clears the BGP4+ message counter for all neighbors.
84. clear ipv6 cache
    Deletes all entries in the dynamic host IPv6 cache.
85. clear ipv6 dhcp-relay delegated-prefixes
    Clears the IPv6 DHCP relay delegated prefixes.
86. clear ipv6 dhcp-relay statistics
    Clears the IPv6 DHCP packet counters.
87. clear ipv6 dhcp6 snooping
    Clears the IPv6 DHCP snooping database.
88. clear ipv6 mld traffic
    Clears the counters on IPv6 multicast listening discovery (MLD) traffic.
89. clear ipv6 mroute
    Removes IPv6 multicast routes from the IPv6 multicast routing table.
90. clear ipv6 multicast counters
    Clears multicast listening discovery (MLD) snooping error and traffic counters on all VLANs.
91. clear ipv6 multicast mcache
    Clears the multicast listening discovery (MLD) mcache on a specific VLAN or on all VLANs.
92. clear ipv6 multicast traffic
    Clears multicast listening discovery (MLD) traffic counters on a specific VLAN or on all VLANs.
93. clear ipv6 neighbor
    Removes entries from the IPv6 neighbor table.
94. clear ipv6 neighbor inspection
    Clears the static neighbor discovery (ND) inspect entries and ND inspection statistics.
95. clear ipv6 ospf
    Clears OSPFv3 data processes, counts, force-spf, neighbors, redistribution, routes, and traffic.
96. clear ipv6 pim cache
    Clears the IPv6 PIM forwarding cache.
97. clear ipv6 pim counters
    Clears IPv6 PIM message counters.
98. clear ipv6 pim hw-resource
    Clears the IPv6 PIM hardware resource fail count for a specific VRF instance or for all VRFs.
99. clear ipv6 pim rp-map
    Clears the entries in an IPv6 PIM Sparse static multicast forwarding table, allowing a new rendezvous point (RP) configuration to be effective immediately.
100. clear ipv6 pim traffic
     Clears counters on IPv6 PIM traffic.
101. clear ipv6 pimsm-snoop
     Clears PIM sparse mode (SM) information.
102. clear ipv6 raguard
     Resets the drop or permit packet counters for Router Advertisement (RA) guard policies.
103. clear ipv6 rip route
     Clears all RIPng routes from the RIPng route table and the IPv6 main route table and resets the routes.
104. clear ipv6 route
     Clears IPv6 routes.
105. clear ipv6 traffic
     Clears IPv6 traffic statistics (resets all fields to zero).
106. clear ipv6 tunnel
     Clears statistics (resets all fields to zero) for all IPv6 tunnels or for a specific tunnel.
107. clear ipv6 tunnel stat
     Clears counters for IPv6 tunnel traffic.
108. clear ipv6 vrrp statistics
     Clears IPv6 Virtual Router Redundancy Protocol (VRRP) statistics.
109. clear ipv6 vrrp-extended statistics
     Clears IPv6 Virtual Router Redundancy Protocol (VRRP) Extended (VRRP-E) statistics.
110. clear link-keepalive statistics
     Clears the UDLD statistics.
111. clear link-oam statistics
     Clears EFM-OAM statistics from all EFM-OAM-enabled interfaces.
112. clear lldp neighbors
     Clears cached Link Layer Discovery Protocol (LLDP) neighbor information.
113. clear lldp statistics
     Clears the global and per-port LLDP neighbor statistics on the device.
114. clear logging
     Clears the log entries from the dynamic buffer, the static buffer, or the local buffer.
115. clear loop-detection
     Clears loop detection statistics and enables all Err-Disabled ports.
116. clear l2protocol dot1q-tunnel counters
     Clears all Q-in-Q BPDU tunnel counters.
117. clear mac-address
     Clears the MAC addresses.
118. clear mac-address cluster
     Clears cluster-specific MAC addresses.
119. clear mac-authentication sessions
     Clears MAC authentication sessions.
120. clear mac-authentication statistics
     Clears MAC authentication statistics
121. clear macsec statistics
     Clears the MACsec traffic statistics for the specified interface.
122. clear management-vrf-stats
     Clears the management Virtual Routing and Forwarding (VRF) rejection statistics.
123. clear mvrp statistics
     Clears the Multiple VLAN Registration Protocol (MVRP) event and packet statistics.
124. clear mstp statistics
     Clears the Multiple Spanning Tree Protocol (MSTP) statistics.
125. clear notification-mac statistics
     Clears the MAC-notification statistics, such as the number of trap messages and number of MAC notification events sent.
126. clear openflow
     Clears flows from the flow table.
127. clear overlay-gateway
     Clears statistics for an entire VXLAN gateway tunnel or for a particular VNI.
128. clear port security
     Clears port security data.
129. clear pstat
     Clears the CPU packet statistics counters.
130. clear public-key
     Clears the authorized client public key from the buffer.
131. clear pvstplus-protect-statistics
     Clears the statistics of the PVST+ Protect feature, configured by means of the pvstplus-protect command.
132. clear rmon statistics
     Clears remote monitoring statistics from the ICX device.
133. clear span statistics
     Clears the Spanning Tree Protocol (STP) statistics for a VLAN.
134. clear stack ipc
     Clears stack traffic statistics.
135. clear statistics
     Clears all counters and statistics.
136. clear statistics openflow
     Clears OpenFlow statistics.
137. clear stp-protect-statistics
     Clears the BPDU drop counters for all ports on the device that have STP Protection enabled.
138. clear web-connection
     Clears all web management sessions.
139. clear webauth vlan
     Clears the authenticated hosts or the blocked hosts.
140. cli timeout
     Sets timeout for CLI session inactivity
141. client
     Configures cluster clients manually.
142. client-auto-detect config
     Configures the automatically detected cluster clients into the running configuration and deploys all of the automatically detected clients.
143. client-auto-detect ethernet
     Enables cluster client automatic configuration on a specific port or range of ports.
144. client-auto-detect start
     Starts the cluster client automatic configuration.
145. client-auto-detect stop
     Stops the automatic configuration process of the running cluster client.
146. client-interface
     Configures the physical port or static LAG port as the Cluster Client Edge Port (CCEP).
147. client-interfaces shutdown
     Shuts down all the local client interfaces in the cluster.
148. client-isolation
     Isolates the client from the network when Cluster Communication Protocol (CCP) is not operational.
149. client-to-client-reflection
     Enables routes from one client to be reflected to other clients by the host device on which it is configured.
150. clock set
     Sets the local clock time and date.
151. clock summer-time
     Sets the device clock summer-time and time zone options.
152. clock timezone
     Sets the device system clock time zone options using either Greenwich Mean time (GMT) or a specified global region with a subzone that uses Universal Time Coordinated (UTC) plus or minus a number of hours.
153. cluster
     Configures a Multi-Chassis Trunking (MCT) cluster.
154. cluster-id
     Configures a cluster ID for the route reflector.
155. compare-routerid
     Enables comparison of device IDs, so that the path-comparison algorithm compares the device IDs of neighbors that sent otherwise equal-length paths.
156. confederation identifier
     Configures a BGP confederation identifier.
157. confederation peers
     Configures subautonomous systems to belong to a single confederation.
158. console timeout
     Configures the idle time for a serial console session.
159. controller-address
     Configures the controller address to be used by the DHCP server (option 52).
160. controller-address (DHCPv6)
     Configures the controller address to be used by the DHCPv6 server (option 52).
161. copy disk0 (config)
     Copies the running configuration or startup configuration from disk0 to flash.
162. copy disk0 flash
     Copies configuration data from an external USB disk to flash.
163. copy disk0 system-manifest
     Copies the system upgrade file from an external USB disk.
164. copy flash disk0
     Copies the image binary or a specified file stored in flash to the external USB flash drive.
165. copy flash flash
     Copies the flash image between primary and secondary flash memory or from active controller primary or secondary flash memory to a stack unit.
166. copy flash scp
     Uploads a copy of an OS image file from a FastIron device’s primary or secondary flash memory to an SCP server. The syntax for copying an image between two devices under test (DUTs) is different from the syntax for uploading from an ICX device to a Linux or a Windows server.
167. copy flash tftp
     Copies contents from ICX device flash memory to a TFTP server.
168. copy https flash
     Copies an image from the HTTPS server to the flash memory.
169. copy https startup-config
     Copies a configuration file from the HTTPS server to the startup configuration file.
170. copy running-config disk0
     Copies the running configuration from internal flash to external USB flash drive.
171. copy running-config https
     Uploads a copy of the running configuration file from an ICX device to an HTTPS server.
172. copy running-config scp
     Uploads a copy of the running configuration file from a FastIron device to an SCP server.
173. copy running-config tftp
     Uploads a copy of the running configuration file from a Layer 2 or Layer 3 ICX switch to a Trivial File Transfer Protocol (TFTP) server.
174. copy scp certificate-data-file
     Downloads a copy of the SSL client certificate from an SCP server to the ICX device
175. copy scp client-certificate
     Downloads a copy of the client RSA certificate from an SCP server to the ICX device.
176. copy scp client-private-key
     Downloads a copy of the client private RSA key from an SCP server to the ICX device
177. copy scp flash
     Downloads a copy of the OS image file from an SCP server to primary or secondary flash memory, or downloads a copy of the boot file or signature file to the device.
178. copy scp license
     Downloads a copy of the license file from an SCP server to the FastIron device.
179. copy scp running-config
     Downloads a copy of the running configuration file from an SCP server to an ICX device.
180. copy scp ssh-pub-key-file
     Downloads a copy of a client public key (DSA/RSA) to the ICX device
181. copy scp ssl-private-key-file
     Downloads a copy of the SSL private key from an SCP host server to the ICX device
182. copy scp startup-config
     Downloads a copy of the startup configuration file from an SCP server to an ICX device.
183. copy scp trust-certificate
     Downloads a copy of the SSL trust certificate from an SCP server to the ICX device
184. copy startup-config disk0
     Copies the system startup-configuration file present in flash to the external USB drive.
185. copy startup-config https
     Uploads a copy of the startup configuration file from a FastIron device to an HTTPS server.
186. copy startup-config scp
     Uploads a copy of the startup configuration file from a FastIron device to an SCP server.
187. copy startup-config tftp
     Uploads a copy of the startup configuration file from a Layer 2 or Layer 3 switch to a TFTP server.
188. copy tftp flash
     Downloads files from a TFTP server to the flash memory of a device.
189. copy tftp license
     Copies the license file from the TFTP server to the license database of the ICX device.
190. copy tftp running-config
     Downloads configuration information from a TFTP server into the ICX device's running configuration.
191. copy tftp startup-config
     Downloads a copy of the startup configuration file from a TFTP server to a Layer 2 or Layer 3 ICX switch.
192. copy tftp system-manifest
     Copies the system manifest package from a TFTP server to the ICX device. Simplifies the software upgrade process into a single command.
193. cpu-limit
     Configures a rate limit to control the number of CPU address messages.
194. critical-vlan
     Specifies the VLAN into which the client should be placed when the RADIUS server times out while authenticating or re-authenticating users.
195. crl-query (PKI)
     Sets the Certificate Revocation List (CRL) query URL.
196. crl-update-time (PKI)
     Sets the frequency of CRL updates.
197. crypto generate
     Regenerates the device key pair.
198. crypto key client generate
     Generates the crypto client key to enable SSH2.
199. crypto key client zeroize
     Deletes the crypto client key pair from the flash memory.
200. crypto key generate
     Generates the crypto key to enable SSH.
201. crypto key zeroize
     Deletes the crypto host key pair from the flash memory.
202. crypto openssl default-encoding
     Modifies the OpenSSL string encoding method from UTF8string to the default method, which is printable string.
203. crypto-ssl certificate
     Generates or deletes a crypto SSL certificate.
204. cycle-time
     Sets a limit as to how many seconds users have to be authenticated by Web Authentication.