The following table contains information about the switch port groups.
The snSwIfInfoTable, which is indexed by ifIndex port format, replaces the snSwPortInfoTable,
which is indexed by a proprietary port format.
Name, OID, and syntax
Access
Description
snSwIfInfoTable
brcdIp.1.1.3.3.5
None
The switch port information table.
snSwIfInfoPortNum
brcdIp.1.1.3.3.5.1.1
Syntax: InterfaceIndex
Read-only
Shows the port or interface index.
snSwIfInfoMonitorMode
brcdIp.1.1.3.3.5.1.2
Syntax: Integer
Read-write
This object is deprecated by snSwIfInfoMirrorMode object and snPortMonitorTable.
snSwIfInfoMirrorPorts
brcdIp.1.1.3.3.5.1.3
Syntax: Integer
Read-write
Contains a list of port or interface indexes (ifindex) that mirror this interface
when monitoring is enabled.
snSwIfInfoTagMode
brcdIp.1.1.3.3.5.1.4
Syntax: Integer
Read-write
Indicates if the port has an 802.1q tag:
tagged(1) - Ports can have multiple VLAN IDs because these ports can be members of
more than one VLAN.
untagged(2) - There is only one VLAN ID per port.
snSwIfInfoTagType
brcdIp.1.1.3.3.5.1.5
Syntax: Integer32
Read-only
Indicates the IEEE 802.1q tag type of an interface. The tag type is embedded in the
two octets in the length or type field of an Ethernet packet. It specifies that the
two octets after the length or type field in an Ethernet packet is the tag value.
Default value: 33024
snSwIfInfoChnMode
brcdIp.1.1.3.3.5.1.6
Syntax: Integer
Read-write
Indicates if the port operates in half- or full-duplex mode:
none(0) - This is not used.
halfDuplex(1) - Half-duplex mode. Available only for 10/100 Mbps ports.
fullDuplex(2) - Full-duplex mode. 100BaseFx, 1000BaseSx, and 1000BaseLx ports operate
only at fullDuplex(2).
The read-back channel status from hardware is as follows:
halfDuplex(1) - Half-duplex mode.
fullDuplex(2) - Full-duplex mode.
The port media type (expansion or regular) and port link type (trunk or feeder) determine
the value of this object. The port cannot be set to half-duplex mode if the port connect
mode is m200e(4). However, the value of this parameter may be automatically set whenever
the expansion port is connected, for example, in the case of a cascade-connecting
device.
The port media type (expansion or regular) and port link type (trunk or feeder) determine
whether this object can be written and the valid values for this object. It is not
allowed to change speed for trunk ports. For expansion ports, all of the listed speeds
can be set; however, the value of this parameter may be automatically set whenever
the expansion port is connected, for example, in the case of a cascade-connecting
device.
snSwIfInfoMediaType
brcdIp.1.1.3.3.5.1.8
Syntax: Integer
Read-only
Shows the media type for the port:
other(1) - Other or unknown media.
m100BaseTX(2) - 100 Mbps copper.
m100BaseFX(3) - 100 Mbps fiber.
m1000BaseFX(4) - 1 Gbps fiber.
mT3(5) - 45 Mbps (T3).
m155ATM(6) - 155 Mbps (ATM).
m1000BaseTX(7) - 1 Gbps copper.
m622ATM(8) - 622 Mbps (ATM).
m155POS(9) - 155 Mbps (POS).
m622POS(10) - 622 Mbps (POS).
m2488POS(11) - 2488 Mbps (POS).
m10000BaseFX(12) - 10 Gbps fiber.
m16GStacking(14) - 16 Gbps fiber.
m100GBaseFX(15) - 100 Gbps fiber.
m40GStacking(16) - 40 Gbps fiber.
m40GBaseFX(17) - 40 Gbps fiber.
m10000BaseTX(18) - 10 Gbps copper.
m2500BaseTX(19) - 2.5 Gbps.
m100GBaseTX(20) - 100 Gbps fiber.
mMultiGigBZ(21) - 2.5G/5G/10G multiGig per seconnd fiber.
m40GBaseTX(22) - 40 Gbps fiber.
m25GBaseTX(23) - 25 Gbps fiber.
snSwIfInfoConnectorType
brcdIp.1.1.3.3.5.1.9
Syntax: Integer
Read-only
Shows the type of connector that the port offers:
other(1) - Other or unknown connector.
copper(2) - Copper connector.
fiber(3) - Fiber connector. This describes the physical connector type.
both(4) - Supports both Copper and Fiber.
snSwIfInfoAdminStatus
brcdIp.1.1.3.3.5.1.10
Syntax: Integer
Read-write
Shows the desired state of all ports:
up(1) - Ready to pass packets
down(2)
testing(3) - No operational packets can be passed (same as ifAdminStatus in MIB-II)
snSwIfInfoLinkStatus
brcdIp.1.1.3.3.5.1.11
Syntax: Integer
Read-only
Shows the current operational state of the interface:
up(1) - Ready to pass packets
down(2)
testing(3) - No operational packets can be passed (same as ifAdminStatus in MIB-II)
snSwIfInfoPortQos
brcdIp.1.1.3.3.5.1.12
Syntax: Integer
Read-write
Indicates the Quality of Service (QoS) level selected for the port:
low(0) - Low priority
high(1) - High priority
level0(0)
level1(1)
level2(2)
level3(3)
level4(4)
level5(5)
level6(6)
level7(7)
snSwIfInfoPhysAddress
brcdIp.1.1.3.3.5.1.13
Syntax: Physical address
Read-only
Shows the physical address of the port.
snSwIfLockAddressCount
brcdIp.1.1.3.3.5.1.14
Syntax: Integer
Read-write
Indicates the number of source MAC addresses that are allowed on the interface.
Valid values: 0 through 2048. The value 0 means an unlimited number of addresses are
allowed.
Default: 8
snSwIfStpPortEnable
brcdIp.1.1.3.3.5.1.15
Syntax: Integer
Read-write
Indicates if STP is enabled for the port:
disabled(0)
enabled(1)
snSwIfDhcpGateListId
brcdIp.1.1.3.3.5.1.16
Syntax: Integer
Read-write
Specifies the ID for a DHCP gateway list entry relative to this switch port.
Valid values: 0 through 32. A value of 0 means that the ID is unassigned.
snSwIfName
brcdIp.1.1.3.3.5.1.17
Syntax: Display string
Read-write
Indicates the port name or description. This description may have been entered using
the CLI.
Valid values: Up to 32 characters for most devices.
snSwIfDescr
brcdIp.1.1.3.3.5.1.18
Syntax: Display string
Read-only
A textual string containing the slot or port information about the interface.
snSwIfInfoAutoNegotiate
brcdIp.1.1.3.3.5.1.19
Syntax: Integer
Read-write
Applies only to Gigabit Ethernet ports.
Indicates if auto-negotiation mode is enabled on the port:
disabled(0) - The port will be placed in non-negotiation mode.
enabled(1) - The port will start auto-negotiation indefinitely until it succeeds.
negFullAuto(2) - The port will start with auto-negotiation. If the negotiation fails,
then it will automatically switch to non-negotiation mode. This option is not supported
in stackable products with Gigabit Ethernet ports.
global(3) - The port negotiation mode follows the value of snSwGlobalAutoNegotiate.
other(4) - Non-Gigabit Ethernet port returns this value.
Default: global(3)
snSwIfInfoFlowControl
brcdIp.1.1.3.3.5.1.20
Syntax: Integer
Read-write
Indicates if port flow control is enabled:
disable(0)
enable(1)
Default: enabled(1)
snSwIfInfoGigType
brcdIp.1.1.3.3.5.1.21
Syntax: Integer
Read-only
Applies only to Gigabit Ethernet ports.
Shows the media type for the port:
m1000BaseSX(0) - 1-Gbps fiber, with a short wavelength transceiver
m1000BaseLX(1) - 1-Gbps fiber, with a long wavelength transceiver (3 km)
m1000BaseLH(2) - 1-Gbps fiber, with a special wavelength transceiver (50 km)
m1000BaseLHB(4) - 1-Gbps fiber, with a special wavelength transceiver (150 km)
m1000BaseTX(5) - 1-Gbps copper (100 m)
m10000BaseSR(6) - 10-Gbps fiber, with a short range wavelength transceiver (100 m)
m10000BaseLR(7) - 10-Gbps fiber, with a long range wavelength transceiver (10 km)
m10000BaseER(8) - 10-Gbps fiber, with an extended range wavelength transceiver (40
km)
sfpCWDM1470nm80Km(9) - 1-Gbps CWDM fiber, with a wavelength 1470nm, reach 80 kms
sfpCWDM1490nm80Km(10) - 1-Gbps CWDM fiber, with a wavelength 1490nm, reach 80 kms
sfpCWDM1510nm80Km(11) - 1-Gbps CWDM fiber, with a wavelength 1510nm, reach 80 kms
sfpCWDM1530nm80Km(12) - 1-Gbps CWDM fiber, with a wavelength 1530nm, reach 80 kms
sfpCWDM1550nm80Km(13) - 1-Gbps CWDM fiber, with a wavelength 1550nm, reach 80 kms
sfpCWDM1570nm80Km(14) - 1-Gbps CWDM fiber, with a wavelength 1570nm, reach 80 kms
sfpCWDM1590nm80Km(15) - 1-Gbps CWDM fiber, with a wavelength 1590nm, reach 80 kms
sfpCWDM1610nm80Km(16) - 1-Gbps CWDM fiber, with a wavelength 1610nm, reach 80 kms
sfpCWDM1470nm100Km(17) - 1-Gbps CWDM fiber, with a wavelength 1470nm, reach 100 kms
sfpCWDM1490nm100Km(18) - 1-Gbps CWDM fiber, with a wavelength 1490nm, reach 100 kms
sfpCWDM1510nm100Km(19) - 1-Gbps CWDM fiber, with a wavelength 1510nm, reach 100 kms
sfpCWDM1530nm100Km(20) - 1-Gbps CWDM fiber, with a wavelength 1530nm, reach 100 kms
sfpCWDM1550nm100Km(21) - 1-Gbps CWDM fiber, with a wavelength 1550nm, reach 100 kms
sfpCWDM1570nm100Km(22) - 1-Gbps CWDM fiber, with a wavelength 1570nm, reach 100 kms
sfpCWDM1590nm100Km(23) - 1-Gbps CWDM fiber, with a wavelength 1590nm, reach 100 kms
snSwIfInfoGigType
(continued)
sfpCWDM1610nm100Km(24) - 1-Gbps CWDM fiber, with a wavelength 1610nm, reach 100 kms
m1000BaseLHX(25) - 1-Gbps fiber, with a special wavelength transceiver (150 km)
m1000BaseLMC(35) - Link Media Copper
mXFP10000BaseSR(36) - 10GBASE fiber, 850nm serial pluggable XFP optic (LC), target
range 300 m over MMF
mXFP10000BaseLR(37) - 10GBASE fiber, 1310nm serial pluggable XFP optic (LC) for up
to 10 km over SMF
mXFP10000BaseER(38) - 10GBASE fiber, 1550nm serial pluggable XFP optic (LC) for up
to 40 km over SMF
mXFP10000BaseSW(39) - Not used
mXFP10000BaseLW(40) - Not used
mXFP10000BaseEW(41) - Not used
mXFP10000BaseCX4(42) - 10GBASE-CX4, XFP module, 15 m, CX4 connector
mXFP10000BaseZR(43) - 1550nm serial pluggable XFP optic (LC) for up to 80 km over
SMF
mXFP10000BaseZRD(44) - 10GBASE-ZR DWDM, XFP optic, 80 km
mXFP10000BaseSRSW(46) - Same as mXFP10000BaseSR(36)
mXFP10000BaseLRLW(47) - Same as mXFP10000BaseLR(37)
mXFP10000BaseEREW(48) - Same as mXFP10000BaseER(38)
m100GBaseTX(51) - 100G BASE fiber
m1000BaseXGSR(136) - 10G BASE fiber
mMultiGigBZ(52) - 2.5/5/10 multiGig fiber
m40GBaseTX(53) - 40GBASE fiber
m25GBaseTX(54) - 25GBASE fiber
notApplicable(255) - A non-gigabit port
mCFP100GBaseSR10(145) - 100-GbE CFP optic (MPO 2x12), SR10, for distances up to 100
m over MMF
mCFP100GBaseLR4(146) - 100-GbE CFP optic (SC), LR4, for distances up to 10 km over
SMF
mCFP100GBaseER4(147) - 100-GbE CFP optic, ER4, for distances up to 40 km over SMF
mCFP100GBase10x10g2Km(148) - 100-GbE CFP optic (LC), 10x10, for distances up to 2
km over SMF
mCFP100GBase10x10g10Km(149) - 100-GbE CFP optic (LC), 10x10, for distances up to 10
km over SMF
qSFP40000BaseSR4(150) - SR proper value for 40G
qSFP40000Base10KmLR4(151) - LR proper vallue for 40G
mCFP2-100GBaseSR10(154)
mCFP2-100GBaseLR4(155)
mCFP2-100GBaseER4(156)
mCFP2-100GBase10x10g2Km(157)
mCFP2-100GBase10x10g10Km(158)
snSwIfFastSpanPortEnable
brcdIp.1.1.3.3.5.1.22
Syntax: Integer
Read-write
Indicates if fast span is enabled on the port:
disabled(0)
enabled(1)
snSwIfFastSpanUplinkEnable
brcdIp.1.1.3.3.5.1.23
Syntax: Integer
Read-write
Indicates if fast span uplink is enabled on the port:
disabled(0)
enabled(1)
snSwIfRouteOnly
brcdIp.1.1.3.3.5.1.25
Syntax: Integer
Read-write
Indicates if Layer 2 switching is enabled on a routing switch port:
disabled(0) - Instructs the routing switch to perform routing first. If that fails,
it performs switching.
enabled(1) - Instructs the routing switch to perform routing only.
For a Layer 2 switching-only product, reading this object always returns "disabled".
Writing "enabled" to this object takes no effect.
Default: disabled(0)
snSwIfPresent
brcdIp.1.1.3.3.5.1.26
Syntax: Integer
Read-only
Indicates if the mini-GBIC optic is absent or present:
false(0)
true(1)
snSwIfGBICStatus
brcdIp.1.1.3.3.5.1.27
Syntax: Integer
Read-only
Indicates if the Gigabit port has a GBIC or miniGBIC port:
GBIC(1) - GBIC
miniGBIC(2) - MiniGBIC
empty(3) - GBIC is missing
other(4) - Not a removable Gigabit port
snSwIfLoadInterval
brcdIp.1.1.3.3.5.1.28
Syntax: Integer
Read-write
Shows the number of seconds for which average port utilization should be calculated.
Valid values: 30 through 300, in 30-second increments.
Default: 300 seconds
snSwIfStatsInFrames
brcdIp.1.1.3.3.5.1.29
Syntax: Counter32
Read-only
Shows the total number of packets received on the interface.
snSwIfStatsOutFrames
brcdIp.1.1.3.3.5.1.30
Syntax: Counter32
Read-only
Shows the total number of packets transmitted out of the interface.
snSwIfStatsAlignErrors
brcdIp.1.1.3.3.5.1.31
Syntax: Counter32
Read-only
Shows the number of dot3StatsAlignmentErrors, which consists of frames received on
a particular interface that are not an integral number of octets in length and do
not pass the FCS check.
The count represented by an instance of this object is incremented when the alignmentError
status is returned by the MAC service to the LLC (or other MAC user). According to
the conventions of IEEE 802.3 Layer Management, received frames for which multiple
error conditions are obtained are counted exclusively according to the error status
presented to the LLC.
snSwIfStatsFCSErrors
brcdIp.1.1.3.3.5.1.32
Syntax: Counter32
Read-only
Shows the number of dot3StatsFCSErrors, which consists of frames received on a particular
interface that are an integral number of octets in length but do not pass the FCS
check.
The count represented by an instance of this object is incremented when the frameCheckError
status is returned by the MAC service to the LLC (or other MAC user). According to
the conventions of IEEE 802.3 Layer Management, received frames for which multiple
error conditions are obtained are counted exclusively according to the error status
presented to the LLC.
snSwIfStatsMultiColliFrames
brcdIp.1.1.3.3.5.1.33
Syntax: Counter32
Read-only
Shows the number of dot3StatsMultipleCollisionFrames, which consists of successfully
transmitted frames on a particular interface for which transmission is inhibited by
more than one collision.
A frame that is counted by an instance of this object is also counted by the corresponding
instance of ifOutUcastPkts, ifOutMulticastPkts, or ifOutBroadcastPkts and is not counted
by the corresponding instance of the dot3StatsSingleCollisionFrames object.
snSwIfStatsTxColliFrames
brcdIp.1.1.3.3.5.1.34
Syntax: Counter32
Read-only
Shows the number of successfully transmitted frames on a particular interface for
which transmission is inhibited by more than one collision. This count is a combination
of the dot3StatsSingleCollisionFrames and dot3StatsMultipleCollisionFrames objects.
snSwIfStatsRxColliFrames
brcdIp.1.1.3.3.5.1.35
Syntax: Counter32
Read-only
Shows the number of successfully received frames on a particular interface for which
transmission is inhibited by more than one collision.
snSwIfStatsFrameTooLongs
brcdIp.1.1.3.3.5.1.36
Syntax: Counter32
Read-only
Shows the number of dot3StatsFrameTooLongs, which consists of frames received on a
particular interface that exceed the maximum permitted frame size.
The count represented by an instance of this object is incremented when the frameTooLong
status is returned by the MAC service to the LLC (or other MAC user). According to
the conventions of IEEE 802.3 Layer Management, received frames for which multiple
error conditions are obtained are counted exclusively according to the error status
presented to the LLC.
snSwIfStatsFrameTooShorts
brcdIp.1.1.3.3.5.1.37
Syntax: Counter32
Read-only
Shows the number frames received on a particular interface that are below the minimum
permitted frame size.
snSwIfStatsInBcastFrames
brcdIp.1.1.3.3.5.1.38
Syntax: Counter32
Read-write
Shows the total number of broadcast packets received on the interface.
snSwIfStatsOutBcastFrames
brcdIp.1.1.3.3.5.1.39
Syntax: Counter32
Read-only
Shows the total number of broadcast packets transmitted out of the interface.
snSwIfStatsInMcastFrames
brcdIp.1.1.3.3.5.1.40
Syntax: Counter32
Read-only
Shows the total number of multicast packets received on the interface.
snSwIfStatsOutMcastFrames
brcdIp.1.1.3.3.5.1.41
Syntax: Counter32
Read-only
Shows the total number of multicast packets transmitted out of the interface.
snSwIfStatsInDiscard
brcdIp.1.1.3.3.5.1.42
Syntax: Counter32
Read-only
Shows the number of inbound packets that will be discarded even though they have no
errors. These packets will be discarded to prevent them from being delivered to a
higher-layer protocol. For example, packets may be discarded to free up buffer space.
snSwIfStatsOutDiscard
brcdIp.1.1.3.3.5.1.43
Syntax: Counter32
Read-only
Shows the number of outbound packets that will be discarded even though they contain
no errors. For example, packets may be discarded to free up buffer space.
snSwIfStatsMacStations
brcdIp.1.1.3.3.5.1.44
Read-only
Shows the total number of MAC Stations connected to the interface.
snSwIfStatsLinkChange
brcdIp.1.1.3.3.5.1.45
Syntax: Counter32
Read-only
Shows the total number of link state changes on the interface.
snSwIfInOctets
brcdIp.1.1.3.3.5.1.46
Syntax: Counter64
Read-only
Shows the total number of octets received on the interface, including framing characters.
This object is a 64-bit counter of the ifInOctets object defined in RFC 1213. The
octet string is in big-endian byte order.
This object has eight octets.
snSwIfOutOctets
brcdIp.1.1.3.3.5.1.47
Syntax: Counter64
Read-only
Shows the total number of octets transmitted out of the interface, including framing
characters. This object is a 64-bit counter of the ifOutOctets object, defined in
RFC 1213. The octet string is in big-endian byte order.
This object has eight octets.
snSwIfStatsInBitsPerSec
brcdIp.1.1.3.3.5.1.48
Syntax: Gauge32
Read-only
Shows the number of bits per second received on the interface over a five-minute interval.
snSwIfStatsOutBitsPerSec
brcdIp.1.1.3.3.5.1.49
Syntax: Gauge32
Read-only
Shows the number of bits per second transmitted out of the interface over a five-minute
interval.
snSwIfStatsInPktsPerSec
brcdIp.1.1.3.3.5.1.50
Syntax: Gauge32
Read-only
Shows the number of packets per second received on the interface over a five-minute
interval.
snSwIfStatsOutPktsPerSec
brcdIp.1.1.3.3.5.1.51
Syntax: Gauge32
Read-only
Shows the number of packets per second transmitted out of the interface over a five-minute
interval.
snSwIfStatsInUtilization
brcdIp.1.1.3.3.5.1.52
Syntax: Integer
Read-only
Indentifies the input network utilization in hundredths of a percent over a five-minute
interval.
Valid values: 0 through 10000
snSwIfStatsOutUtilization
brcdIp.1.1.3.3.5.1.53
Syntax: Integer
Read-only
Shows the output network utilization in hundredths of a percent over a five-minute
interval.
Valid values: 0 through 10000
Note: Ethernet devices must allow a minimum idle period between transmission of frames
known as interframe gap (IFG) or interpacket gap (IPG). The gap provides a brief recovery
time between frames to allow devices to prepare to receive the next frame. The minimum
IFG is 96 bit times, which is 9.6 microseconds for 10 Mbps Ethernet, 960 nanoseconds
for 100 Mbps Ethernet, and 96 nanoseconds for 1 Gbps Ethernet. In addition, to account
for the bit rate on the port, port utilization should also account for the IFG, which
normally is filtered by the packet synchronization circuitry. Refer to the etherHistoryUtilization
objects in the RFC 1757: Remote Network Monitoring Management Information Base for
details.
snSwIfStatsInKiloBitsPerSec
brcdIp.1.1.3.3.5.1.54
Syntax: Unsigned32
Read-only
Shows the bit rate, in kilobits per second, received on a 10 Gigabit or faster interface
within a five-minute interval.
snSwIfStatsOutKiloBitsPerSec
brcdIp.1.1.3.3.5.1.55
Syntax: Unsigned32
Read-only
Shows the bit rate, in kilobits per second, transmitted from a 10 Gigabit or faster
interface within a five-minute interval.
snSwlfStatsInJumboFrames
brcdIp.1.1.3.3.5.1.56
Syntax: Counter64
Read-only
The total number of jumbo packets received on the interface.
snSwlfStatsOutJumboFrames
brcdIp.1.1.3.3.5.1.57
Syntax: Counter64
Read-only
The total number of jumbo packets transmitted out of the interface.
snSwIfInfoNativeMacAddress
brcdIp.1.1.3.3.5.1.62
Syntax: PhysAddress
Read-only
The port’s native MAC address. The native MAC address represents the switch port.
snSwIfQosMonitorDropCounterMode
brcdIp.1.1.3.3.5.1.63
Syntax: Integer
Read-write
Enables or disables the monitoring egress drop counter on the port.
The ICX 7150 has a set of queue drop counters and a port is selected to associate
with these counters. Only when the port is selected, these drop counters are monitored
and included in the total egress drop for the port. You can select only one port in
a unit.
This OID is only applied to the ICX 7150 platform and is enabled by default on other
ICX platforms.
Valid values:
disable(0)
enable(1)
snSwIfLRMAdapterPresent
brcdIp.1.1.3.3.5.1.64
Syntax: Integer
Read-only
Displays the state for the Long Reach Module (LRM) adapter presented on this port.
Some ICX devices support LRM optics on 10-Gbps fiber ports. The LRM adapter is used
to support LRM optics on those switch ports.
Valid values are false and true. The default is the false state.
false: The port is not connected to LRM adapter
true: The port is connected to LRM adapter
snSwIfStpBPDUGuardMode
brcdIp.1.1.3.3.5.1.65
Syntax: TruthValue
Read-write
The status of the spanning tree BPDU guard on an Ethernet port.
The default is the false state.
snSwIfStpRootGuardMode
brcdIp.1.1.3.3.5.1.66
Syntax: TruthValue
Read-write
The status of the spanning tree root guard on an ethernet port. Declares the port
to be on root guard for all spanning trees.
The default is the false state.
snSwIfRstpAdminEdgePortMode
brcdIp.1.1.3.3.5.1.67
Syntax: TruthValue
Read-write
The status of the rapid spanning tree admin edge port on an Ethernet port. Declares
the port to be an operational edge for all VLANs.
The default is the false state.
snSwIfInfoClockMode
brcdIp.1.1.3.3.5.1.68
Syntax: Integer
Read-write
Note: SET is not supported in FastIron 08.0.91.
The port can be configured to operate in either master or slave mode. The values are:
none(0) - Not configured or not supported for clock mode, like fiber ports.
master(1) - Master mode
slave(2) - Slave mode
auto(3) - Auto mode is the default value for copper ports.
snSwIfProtectedMode
brcdIp.1.1.3.3.5.1.69
Syntax: TruthValue
Read-write
This is a new MIB object for the protected mode at the port level. The default is
false state.
Note: Only GET is supported in FastIron 08.0.95.
snSwIfTrustDscpMode
brcdIp.1.1.3.3.5.1.70
Syntax: TruthValue
Read-write
The status of Trust DSCP at Port Level QoS/VOIP
settings.
(1) - Trust DSCP is configured.
(2) - Trust DSCP is not configured (Default).
snSwIfVoiceVlanId
brcdIp.1.1.3.3.5.1.71
Syntax: Integer32
Read-write
MIB object for configuring or reading the configuration of
port-level QoS and VOIP settings for a voice VLAN.
Configure voice VLAN
Read the voice VLAN config
snSwIfPortLoopDetectionMode
brcdIp.1.1.3.3.5.1.72
Syntax: TruthValue
Read-write
Specifies whether Loop Detection is enabled on the Interface or
not.
Possible Values are:
2: Not Enabled
1: Enabled
snSWIfErrDisableStatus
brcdIp.1.1.3.3.5.1.73
Syntax: Integer
Read-only
The port's error disable status. Possible
values are:
not-error-disable(0) the port is not under error disable
state.
cause-counter(15) ERRDISABLE_CAUSE_CNT, this is not a valid
reason, just the reason counter
snSwIfInfoLimitTable
brcdIp.1.1.3.3.12
NA
Rate limiting table for different types of traffic for a port. This MIB object is
used to retrieve BUM rate limit information.
snSwIfInfoLimitEntry
brcdIp.1.1.3.3.12.1
NA
An entry in the snSwIfInfoLimitTable indicates the configuration on a specified port
for rate limiting values.
snSwIfInfoLimitType
brcdIp.1.1.3.3.12.1.1
Syntax: Integer
Read-only
The type of the limit. The value specified applies for broadcast, unknown unicast,
and multicast traffic.
snSwIfInfoLimitPkts
brcdIp.1.1.3.3.12.1.2
Syntax: Unsigned32
Read-only
Limit the number of packets per second forwarded out of the switch port. Setting
the value to 0 disables the limitation check. The default value is 0.
snSwIfInfoLimitBits
brcdIp.1.1.3.3.12.1.3
Syntax: Unsigned32
Read-only
Limit the number of kilobytes per second forwarded out of the switch port. Setting
the value to 0 disables the limitation check. The default value is 0.
snSwIfInfoLimitThreshold
brcdIp.1.1.3.3.12.1.4
Syntax: Unsigned32
Read-only
The number of packets to be dropped when the rate limit is reached before taking
the specified action (such as shutting down the port).
snSwIfInfoLimitShutdownTime
brcdIp.1.1.3.3.12.1.5
Syntax: Unsigned32
Read-only
Specifies the time the port should be in the down state. Takes effect only if the
threshold is configured. The default value is 300.
snSwIfInfoLimitLog
brcdIp.1.1.3.3.12.1.6
Syntax: Unsigned32
Read-only
Enable or disable the logging of the rate limit occurrence.