Switch group configuration

The switch group configuration table is supported on the RUCKUSFastIron devices.

Name, OID, and syntax

Access

Description

snSwGroupOperMode

brcdIp.1.1.3.1.1

Syntax: Integer

Read-write

Indicates if switch ports have VLANs defined:

  • noVLan(1) - All switch ports with no port VLANs and no tag assigned.
  • vlanByPort(2) - All switch ports with basic port-based VLANs.
snSwGroupIpL3SwMode

brcdIp.1.1.3.1.2

Syntax: Integer

Read-write

Indicates if the Layer 3 IP switch is enabled for the switch group:

  • disabled(0)
  • enabled(1)
snSwGroupIpMcastMode

brcdIp.1.1.3.1.3

Syntax: Integer

Read-write

Indicates if the IP multicast pruning mode is enabled for the switch group:

  • disabled(0)
  • active(1)
  • passive(2)
snSwGroupDefaultCfgMode

brcdIp.1.1.3.1.4

Syntax: Integer

Read-write

Indicates if the switch group contains a default configuration. If the default configuration is overwritten, the state will change to non-default:

  • default(1) - Has a default configuration.
  • nonDefault(2) - Has a non-default configuration.
snSwGroupSwitchAgeTime

brcdIp.1.1.3.1.5

Syntax: Integer32

Read-write

Sets the aging period for ports on the device, defining how long a port address remains active in the address table.

Valid values: 0 = no aging, or 67 - 65535 seconds

Default: 300 seconds

snVLanGroupVlanCurEntry

brcdIp.1.1.3.1.6

Syntax: Integer32

Read-only

Shows the number of VLANs that are currently configured.

snFdbTableCurEntry

brcdIp.1.1.3.1.9

Syntax: Integer32

Read-only

Shows the total number of entries in the Filtering Databse (FDB) that are configured currently.

snFdbTableStationFlush

brcdIp.1.1.3.1.10

Syntax: Integer

Read-write

Shows the state of the flush operation for the FDB table.

The following value can be written:

  • flush(3) - Perform the flush operation. After the flush operation starts, any new flush request is rejected until the operation is complete or failed.

The following values can only be read:

  • normal(1) - Normal state
  • error(2) - Operation failed
  • flushing(4) - Operation is in process
snPortStpSetAll

brcdIp.1.1.3.1.11

Syntax: Integer32

Read-write

The value of this object is 1, which means that Port STP Set-all command is invoked. The snPortStpPriority and snPortStpPathCost which are the read-write STP-related attributes of the first row of the table, will be used to set the same attributes for all the ports in the system.

Note: Before setting this object, all the intended attributes of the given row of the table must be set. Otherwise, the current data of the row will be used to set the entire port table. The previous setting will be overwritten by the new one.
snSwProbePortNum

brcdIp.1.1.3.1.12

Syntax: Integer32

Read-write

Indicates which chassis port is assigned as the chassis switch probe port. That port operates as a traffic analyzer port. Only one port in the chassis or stackable switch can be assigned as the traffic analyzer port. The value of this object represents the following:

  • Bit 0 to bit 7 - Port number
  • Bit 8 to bit 11 - Slot number
snSw8021qTagMode

brcdIp.1.1.3.1.13

Syntax: Integer

Read-write

Indicates if IEEE802.1q has been enabled for the switch group:

  • disabled(0)
  • enabled(1)

Default: disabled(0)

snSwGlobalStpMode

brcdIp.1.1.3.1.14

Syntax: Integer

Read-write

Indicates whether or not Spanning Tree System Global Mode has been enabled for the switch group:

  • disabled(0)
  • enabled(1)
snSwIpMcastQuerierMode

brcdIp.1.1.3.1.15

Syntax: Integer

Read-write

The IP Multicast pruning mode is configured in either Non-Querier or Querier mode.

  • querier(1) - Send out host queries. (active)
  • nonQuerier(2) - Do not send out host queries. (passive)

Default: querier(1)

snSwViolatorPortNumber

brcdIp.1.1.3.1.17

Syntax: Integer32

Read-only

Indicates the port number of the switch or router that receives the violator packet. This number is included in the locked address violation trap. The value of this object contains the following:

  • Bit 0 to bit 7 - Port number
  • Bit 8 to bit 11 - Slot number (for chassis devices only)
snSwViolatorMacAddress

brcdIp.1.1.3.1.18

Syntax: MAC address

Read-only

Indicates the source MAC address of the violator packet received by the switch or router. This number is included in the locked address violation trap.

snVLanGroupVlanMaxEntry

brcdIp.1.1.3.1.19

Syntax: Integer32

Read-write

Shows the maximum number of VLAN entries that can be configured.

snSwEosBufferSize

brcdIp.1.1.3.1.20

Syntax: Integer32

Read-only

Specifies buffer size for all the different EOS buffers.

snSwPortEntrySize

brcdIp.1.1.3.1.22

Syntax: Integer32

Read-only

Specifies the size of each port table entry.

snFdbStationEntrySize

brcdIp.1.1.3.1.23

Syntax: Integer32

Read-only

Specifies the size of each FDB station table entry.

snPortStpEntrySize

brcdIp.1.1.3.1.24

Syntax: Integer32

Read-only

Specifies the size of each port STP table entry.

snSwEnableBridgeNewRootTrap

brcdIp.1.1.3.1.25

Syntax: Integer

Read-write

Indicates whether the SNMP agent process is permitted to generate bridge new root traps.

snSwEnableBridgeTopoChangeTrap

brcdIp.1.1.3.1.26

Syntax: Integer

Read-write

Indicates whether the SNMP agent process is permitted to generate bridge topology change traps.

snSwClearCounters

brcdIp.1.1.3.1.33

Syntax: Integer

Read-write

Clears software counters:

  • valid(0) - An SNMP-GET of this MIB shows that it is a valid command to use.
  • clear(1) - Clear counter commands of the following counters: Dot3, MIB2, IP, and IPX counters for all ports.
snSw8021qTagType

brcdIp.1.1.3.1.34

Syntax: Integer32

Read-only

Specifies the IEEE802.1q tag type that is embedded in the length or type field of an Ethernet packet. It specifies that the two octets after the length or type field in an Ethernet packet are the tag value.

Default: 33024

snSwBroadcastLimit

brcdIp.1.1.3.1.35

Syntax: Integer32

Read-write

Specifies the number of broadcast packets per second. This limits the number of broadcast packets to forward out of the switch ports. Setting this object to 0 disables the limitation check.

Default: 0

snSwMaxMacFilterPerSystem

brcdIp.1.1.3.1.36

Syntax: Integer32

Read-only

Specifies the maximum number of MAC filters per system in the MAC filter table.

snSwMaxMacFilterPerPort

brcdIp.1.1.3.1.37

Syntax: Integer32

Read-only

Specifies the maximum number of MAC filters per port in the port MAC access filter table.

snSwDefaultVLanId

brcdIp.1.1.3.1.38

Syntax: Integer

Read-write

Shows the VLAN ID of the default port VLAN.

Valid values: 1 - 4095

snSwGlobalAutoNegotiate

brcdIp.1.1.3.1.39

Syntax: Integer

Read-write

Applies only to Gigabit Ethernet ports.

Specifies the negotiation mode of the port:

  • disable(0) - All Gigabit Ethernet ports are in non negotiation mode.
  • enable(1) - All Gigabit Ethernet ports will start auto-negotiation indefinitely until they succeed.
  • negFullAuto(2) - All Gigabit Ethernet ports will start with auto-negotiation. If the negotiation fails, then they will automatically switch to non-negotiation mode. Gigabit Ethernet ports on all stackable products do not support negFullAuto(2).
  • other(3)

Default: negFullAuto(2)

snSwQosMechanism

brcdIp.1.1.3.1.40

Syntax: Integer

Read-write

Specifies the Quality of Service (QoS) mechanism:

  • strict(0)
  • weighted(1)

Default: weighted(1)

snSwSingleStpMode

brcdIp.1.1.3.1.41

Syntax: Integer

Read-write

Indicates if the Single Spanning Tree System Mode in the Switch Group is enabled:

  • disabled(0)
  • enabled(1)

Default: disabled(0)

snSwFastStpMode

brcdIp.1.1.3.1.42

Syntax: Integer

Read-write

Indicates if Fast Spanning Tree System Mode in the Switch Group is enabled:

  • disabled(0)
  • enabled(1)
snSwSingleStpVLanId

brcdIp.1.1.3.1.44

Syntax: Integer32

Read-only

The VLAN ID of the Single Spanning Tree VLAN if Single Spanning Tree was enabled. This object returns zero if Single Spanning Tree was disabled.

snSwJumboMode

brcdIp.1.1.3.1.45

Syntax: Integer

Read-only

Jumbo mode enables support of the jumbo frame (10200 bytes). Jumbo mode can be enabled or disabled; the default is enabled mode.

Please note that enabling/disabling jumbo mode will take effect only after saving the configuration and performing a system reload.

  • disabled(0)
  • enabled(1)

snSwIpMcastVersion

brcdIp.1.1.3.1.47

Syntax: Integer32

Read-write

Sets the Multicast version at the global level

Values are 2 or 3. The default is 2.

snSwErrDisableRecoveryTimeout

brcdIp.1.1.3.1.49

Syntax: Unsigned 32

Read-write

The Error-Disable timeout value in seconds

Valid Values: 0 to 65535

Default Value: 300
snSwErrDisableRecoveryCause

brcdIp.1.1.3.1.50

Syntax: Unsigned 32

Read-write

Configures the errdisable cause support recovery.

Valid values:

0 = no recovery is supported, or other value

bit 0 - Enable auto-recovery from all causes

bit 1 - Enable auto-recovery from BPDU guard

bit 2 - Enable auto-recovery from loop-detection

bit 4 - Enable auto-recovery from packet inError

bit 5 - Enable auto-recovery from LOAM remote critical event

bit 12 - Enable auto-recovery from pvstplus-protect

bit 13 - Enable auto-recovery from bpdu tunnel threshold

bit 14 - Enable auto-recovery from lag operational speed mismatch

Default: 0
Parent topic: Switch Group Configuration