| ruckusIpv4AclFilterTable
snSwitch.45.1.2.1.1
Syntax: SEQUENCE OF RuckusIpv4AclFilterEntry
|
NA
|
Table of Ruckus IPv4 Access Control List filters.
|
| ruckusIpv4AclFilterEntry
snSwitch.45.1.2.1.1.1
Syntax: RuckusIpv4AclFilterEntry
|
NA
|
An entry in the Ruckus IPv4 Access Control List Filter table.
|
| ruckusIpv4AclFilterSeqNum
snSwitch.45.1.2.1.1.1
Syntax: Unsigned32
|
NA
|
Specifies the sequence number for this ACL filter.
|
| ruckusIpv4AclFilterAction
snSwitch.45.1.2.1.1.2
Syntax: AclAction
|
Read-create
|
Action to take if the IP packet matches with this ACL filter.
|
| ruckusIpv4AclFilterStdProtocol
snSwitch.45.1.2.1.1.3
Syntax: Integer
|
Read-create
|
Standard transport protocols are allowed. The extended option enables the definition
of other protocols using the OID ruckusIpv4AclFilterExtProtocol which takes any value.
ip(0)
icmp(1)
igmp(2)
tcp(6)
udp(17)
ip6(41)
rsvp(46)
gre(47)
esp(50)
ospf(89)
pim(103)
extended(255)
|
| ruckusIpv4AclFilterExtProtocol
snSwitch.45.1.2.1.1.4
Syntax: Integer
|
Read-create
|
Any transport protocol other than standard protocols mentioned with ruckusIpv4AclFilterStdProtocol
OID. The value 0 means any protocol.
|
| ruckusIpv4AclFilterSrcAddr
snSwitch.45.1.2.1.1.5
Syntax: InetAddressIPv4
|
Read-create
|
Source IPv4 address to match the packets.
|
| ruckusIpv4AclFilterSrcMask
snSwitch.45.1.2.1.1.6
Syntax: InetAddressIPv4
|
Read-create
|
Source IPv4 address mask used in combination with source IPv4 address to derive effective
address for matching.
|
| ruckusIpv4AclFilterSrcOperator
snSwitch.45.1.2.1.1.7
Syntax: AclOperator
|
Read-create
|
Type of comparison to perform. For now, this applies only to TCP or UDP for comparing
the port number.
|
| ruckusIpv4AclFilterSrcPortLow
snSwitch.45.1.2.1.1.8
Syntax: Unsigned32
|
Read-create
|
Specifies the TCP or UDP port number to match in packets. If the operator is "range",
it specifies the start of the range.
|
| ruckusIpv4AclFilterSrcPortHigh
snSwitch.45.1.2.1.1.9
Syntax: Unsigned32
|
Read-create
|
Used only if the operator is defined as "range", where it specifies the end of the
range.
|
| ruckusIpv4AclFilterDestAddr
snSwitch.45.1.2.1.1.10
Syntax: InetAddressIPv4
|
Read-create
|
Destination IPv4 address to match in packets.
|
| ruckusIpv4AclFilterDestMask
snSwitch.45.1.2.1.1.11
Syntax: InetAddressIPv4
|
Read-create
|
Destination IPv4 address mask used in combination with source IPv4 address to derive
effective address for matching.
|
| ruckusIpv4AclFilterDestOperator
snSwitch.45.1.2.1.1.12
Syntax: AclOperator
|
Read-create
|
Type of comparison to perform. For now, this only applies to TCP or UDP for comparing
the port number.
|
| ruckusIpv4AclFilterDestPortLow
snSwitch.45.1.2.1.1.13
Syntax: Unsigned32
|
Read-create
|
Specifies the TCP or UDP port number to match in packets. If the operator is 'range',
it specifies the start of range.
|
| ruckusIpv4AclFilterDestPortHigh
snSwitch.45.1.2.1.1.14
Syntax: Unsigned32
|
Read-create
|
Used only if the operator is defined as 'range', where it specifies the end of range.
|
| ruckusIpv4AclFilterEstablished
snSwitch.45.1.2.1.1.15
Syntax: TruthValue
|
Read-create
|
Enable or disable the filtering of established TCP packets of which the ACK or RESET
flag is on. This filter only applies to the TCP transport protocol.
|
| ruckusIpv4AclFilterPrecedence
snSwitch.45.1.2.1.1.16
Syntax: IpPrecedence
|
Read-create
|
Specifies the IP precedence value to match in packets.
|
| ruckusIpv4AclFilterTos
snSwitch.45.1.2.1.1.17
Syntax: IpTos
|
Read-create
|
Refers to the IP ToS value in the range 0 through 15, which is the sum of the numeric
values of the following options:
0x0: Normal ToS
0x1: Minimum monetary cost ToS
0x2: Maximum reliability ToS
0x4: Maximum throughput ToS
0x8: Minimum delay
|
| ruckusIpv4AclFilterIcmpType
snSwitch.45.1.2.1.1.18
Syntax: Integer
|
Read-create
|
Specifies the ICMP type for matching if the protocol is ICMP. The value 0 means to
ignore the field.
|
| ruckusIpv4AclFilterIcmpCode
snSwitch.45.1.2.1.1.19
Syntax: Integer
|
Read-create
|
ICMP Message Code value. Used in combination with ICMP Message Type to set up an
ICMP filter. This object is not used with any other protocol. The value 0 means to
ignore the field. The supported values are:
Type: Echo reply
Type: Destination unreachable
Type: Source quench
Type: Redirect
Type: Echo request
Type: Router advertisement
Type: Router solicitation
Type: Time exceeded
Type: Parameter problem
Type: Timestamp request
Type: Timestamp reply
Type: Information request
Type: Information reply
Type: Address mask request
Type: Address mask reply
|
| ruckusIpv4AclFilterExtIcmpType
snSwitch.45.1.2.1.1.20
Syntax: Integer
|
Read-create
|
Any type that cannot be specified using the standard types can be specified using
this object.
|
| ruckusIpv4AclFilterPolicyName
snSwitch.45.1.2.1.1.21
Syntax: AclPolicyName
|
Read-create
|
Specifies the DSCP value to use in matching or marking.
|
| ruckusIpv4AclFilterDscpMatch
snSwitch.45.1.2.1.1.22
Syntax: Integer
|
Read-create
|
Specifies the DSCP value for matching with this filter.
|
| ruckusIpv4AclFilterDscpForce
snSwitch.45.1.2.1.1.23
Syntax: Integer
|
Read-create
|
Specifies the DSCP value to be used for marking in outgoing packets matching this
filter.
|
| ruckusIpv4AclFilterPriorityMatch
snSwitch.45.1.2.1.1.24
Syntax: Integer
|
Read-create
|
Specifies the 802.1P priority for matching with this filter.
|
| ruckusIpv4AclFilterPriorityForce
snSwitch.45.1.2.1.1.25
Syntax: Integer
|
Read-create
|
Specifies the 802.1P priority to be used for marking in outgoing packets matching
this filter.
|
| ruckusIpv4AclFilterInternalPriority
snSwitch.45.1.2.1.1.26
Syntax: Integer
|
Read-create
|
QoS priority option for this filter.
|
| ruckusIpv4AclFilterMirrorPkts
snSwitch.45.1.2.1.1.27
Syntax: TruthValue
|
Read-create
|
Mirror packets matching ACL permit clause.
|
| ruckusIpv4AclFilterLogEnable
snSwitch.45.1.2.1.1.28
Syntax: TruthValue
|
Read-create
|
Specifies if logging is enabled for the filter.
|
| ruckusIpv4AclFilterComments
snSwitch.45.1.2.1.1.29
Syntax: DisplayString
|
Read-only
|
Remark description of individual Access Control List entry.
|
| ruckusIpv4AclFilterRowStatus
snSwitch.45.1.2.1.1.30
Syntax: RowStatus
|
Read-create
|
The row status variable is used according to installation and removal conventions
for conceptual rows. Setting this object to createAndGo(4) results in the creation
of the IPv4 ACL filter. Setting this object to destroy(6) removes this IPv4 ACL filter.
Other values are ignored.
|