Displaying General or Detailed Information about Stack Members
Replace examples with non-ICX 7750 examples. The series should include a general show
stack command, a show stack unit command, and a show stack detail command that are
all related.
You can display information about any member in a stack by entering
show commands from the active controller console port. If you enter
show commands from a unit that is not the active controller, the information may not be
displayed correctly.
The
show stack command displays general information about a stack, for all members, for a specified
member, or for all members with additional detail.
The following output covers the entire stack and includes role history for each unit, beginning with the initial role the unit held.
ICX7750-26Q Router# show stack
T=29m36.7: alone: standalone, D: dynamic cfg, S: static
ID Type Role Mac Address Pri State Comment
1S ICX7750-26QXG standby 748e.f8f9.6300 128 remote Ready
2S ICX7750-26QXG member cc4e.2438.7280 0 remote Ready
4S ICX7750-26QXG active cc4e.2438.7500 128 local Ready
active standby
+---+ +---+ +---+
-2/1| 4 |2/4--2/1| 2 |2/4--2/1| 1 |2/4-
| +---+ +---+ +---+ |
| |
|-------------------------------------|
Standby u1 -protocols ready, can failover or manually switch over
Role history: N: standalone, A: active, S: standby, M: member
U1: N->A->S->M->S, U2: M->S->A->S->M, U4: M->S->A
If you add a stack member ID, output is displayed for that member only.
ICX7750-26Q Router# show stack 1 T=12m6.2: alone: standalone, D: dynamic cfg, S: static ID Type Role Mac Address Pri State Comment 1 S ICX7750-26QXG active 748e.f8f9.6300 0 local Ready ICX7750-26Q Router# show stack 2 T=12m16.3: alone: standalone, D: dynamic cfg, S: static ID Type Role Mac Address Pri State Comment 2 D ICX7750-26QXG member cc4e.2438.7280 0 remote Ready ICX7750-26Q Router# show stack 3 T=12m20.6: alone: standalone, D: dynamic cfg, S: static ID Type Role Mac Address Pri State Comment 3 D ICX7750-26QXG standby cc4e.2438.7500 0 remote Ready
If you add the
detail keyword to the
show stack command, output resembles the following example.
ICX7750-26Q Router# show stack detail
T=18m33.4: alone: standalone, D: dynamic cfg, S: static
ID Type Role Mac Address Pri State Comment
1 S ICX7750-26QXG active 748e.f8f9.6300 0 local Ready
2 D ICX7750-26QXG member cc4e.2438.7280 0 remote Ready
3 D ICX7750-26QXG standby cc4e.2438.7500 0 remote Ready
active standby
+---+ +---+ +---+
=2/1| 1 |2/4==2/1| 3 |2/4--2/1| 2 |2/4=
| +---+ +---+ +---+ |
| |
|-------------------------------------|
Will assign standby in 11 sec due to all ready
Standby u3 - protocols ready, can failover
Current stack management MAC is 748e.f8f9.6300
Image-Auto-Copy is Enabled.
Stack Port Status Neighbors
Unit# Stack-port1 Stack-port2 Stack-port1 Stack-port2
1 up (1/2/1-1/2/2) up (1/2/4-1/2/6) U2 (2/2/4-2/2/5) U3 (3/2/1-3/2/3)
2 up (2/2/1) up (2/2/4-2/2/5) U3 (3/2/4) U1 (1/2/1-1/2/2)
3 up (3/2/1-3/2/3) up (3/2/4) U1 (1/2/4-1/2/6) U2 (2/2/1)
Unit# System uptime
1 18 minute(s) 33 second(s)
2 17 minute(s) 30 second(s)
3 18 minute(s) 46 second(s)
Field Descriptions for the
show stack Command
Note: The active controller removes the dynamic configuration of a unit when the unit leaves
the stack. However, if there is a static trunk configuration associated with the unit,
the active controller cannot remove the dynamic configuration. In this case, you must
remove the static trunk and use the
no stack unit
stack-unit command to manually remove the configuration.