Single
Interface (default)—For the controller to send
traffic from its data plane from a single interface.
Access
and Core Interface—For the controller to send
traffic to the access and core networks separately.
Note: To
separate the access and core networks
Use static routes, if the data plane is required
to connect to IP addresses in the core network
(for example, for DHCP relay or L2oGRE
termination) and the destination IP addresses are
not part of the core subnet.
Keep
original configuration—For the controller to keep
the original manual Data Plane setup.
Network >
Primary
(Access) Interface
IP
Mode
Indicates the mode of assigning the IP address to
this interface.
Select the option:
Static (recommended)—To manually assign an IP address to
this interface manually.
Enter
the IP
Address.
Enter
Subnet Mask for the IP address.
Enter
the Gateway router address.
Enter
the Primary DNS Server IP address.
Enter
the Secondary DNS Server IP address.
Enter
VLAN ID to tag traffic.
5.1 update - used
across platforms
Choose the Data NAT IP/Port Configured option.
Enter
Data NAT IP address.
Enter Data NAT Port address.
DHCP—To automatically obtain an IP address from a DHCP
server on the network.
Enter
VLAN ID to tag traffic.
Choose the Data NAT IP/Port Configured option.
Network >
IPv6 Primary
(Access) Interface
IP
Mode
Indicates the mode of assigning the IP address to
this interface.
Select the option:
Static (recommended)—To manually assign an IP address to
this interface manually.
Enter
the IP
Address.
Enter
the Gateway router address.
Enter
the Primary DNS Server IP address.
Enter
the Secondary DNS Server IP address.
Auto—To automatically obtain an IP address from a DHCP
server on the network.
Network >
Secondary
(Core) Interface (applicable for Interface
Mode: Access and Core Interfaces)
IP
Address
Indicates the IP address of the core network
interface.
Enter the IP address.
Note: The
secondary/core interface IP address must be configured manually;
DHCP is unsupported.
Subnet Mask
Indicates the IP address of the subnet mask.
Enter the subnet mask.
VLAN
Indicates that the traffic is tagged with a VLAN ID.
Enter the VLAN ID.
Note: If VLANS are
configured on both the access and core networks, the VLAN ID
that you enter here must be different from the one that you
entered for the primary/access interface.
Note: You cannot
configure the IP address and VLAN settings for a virtual Data
Plane from the Primary (Access) and Secondary (Core) Interface
sections. Only vSZ-H supports virtual Data Plane.
Disconnect AP when core link down
Indicates that the AP is disconnected secondary core
link is down.
Select the check box.
Static
Routes
Network Address
Indicates the destination IP address of this route.
Enter the IP address.
Subnet Mask
Indicates a subnet mask for the IP address.
Enter the subnet mask.
Gateway
Indicates the IP address of the gateway router.
Enter the IP address of the gateway router.
Add
Adds the static route settings.
Click Add.
CALEA
Relay
Mark this Data Plane as CALEA Relay (This feature is
supported only for vSZ-E and vSZ-H controllers)
Indicates that the data plane uses CALEA relay.
Select the check box.
3.6 Update
DHCP
Profile
DHCP Profile
Indicates the data plane DHCP service profile.
Choose the DHCP service profile from the drop-down.
NAT
Profile
NAT Profile
Indicates the data plane NAT service profile.
Choose the NAT service profile from the drop-down.
3.6 Update
Syslog
Enable DHCP syslog
Enables syslog to record the DHCP logs.
Select the check box.
Enable NAT syslog
Enables syslog to record the NAT logs.
Select the check box.
Syslog Server IP
Indicates the IP address of the remote syslog
server.
Enter the IP address of the remote syslog server.
Syslog Server Port
Indicates the port number of the remote syslog
server.
Enter the Port number of the remote syslog server.
Note: You can restart a data
plane. To do so, select the data plane from the list and click Restart.
Note:
5.1
update - used across platforms
You can approve or delete a data
plane. To do so, select the data plane from the list and click Approve or Delete respectively.
You can also download debug logs or switch over clusters. To do so, select the
data
plane from the list, click More and select Download or
Switch Over
Clusters respectively.
Note: All configuration changes applicable
to vSZ-H are also applicable to SZ100-D.