model

Configures model-specific settings for all APs of a certain model within an AP group.
model WORD [ port-setting ] [status-leds { enable | disable } ] [external-antenna { 2.4Ghz } {(11BG) | (11NG) } | { 5Ghz } { (11NA) | (11A) }{enable | disable | gain | 2-antennas | 3-antennas }] [max-clients NUMBER ] [ poe-out { enable | disable } ] [internal-heater { enable |disable } ] [ cband-channels { enable |disable } ][ cband-license { enable |disable } ][ lacp-status { enable |disable } ][ power-mode {auto | 802.3af | 802.3at | 802.3bt5 | 802.3bt6| 802.3bt7 } ][ 802.3af-txchain { 1 | 2 | 4 } ][ band-scheme { 2-5 | 2-5-6 } ]
no model WORD [ port-setting ] [status-leds-override ] [external-antenna-override ] [max-clients ] [ poe-out-override ] [internal-heater-override ] [ cband-channels-override ][ cband-license-override ][ lacp-status-override ][ power-mode-override ][ 802.3af-txchain-override ] [ band-scheme-override ]
Command Default

The default AP model-specific setting values are:

Parameter Value
status-leds Enabled
external-antenna Auto
max-clients 100
poe-out Disabled
internal-heater Disabled
cband-channels Disabled
cband-license Disabled
lacp-status Disabled
power-mode Varies depending on AP model
802.3af-txchain Varies depending on AP model
band-scheme 2-5-6 (if the country code supports 6 GHz). The default setting is dependent on the country code associated with the AP; for example, an AP in a country that does not support 6GHz defaults to 2-5 mode. This command is supported only on AP model R670.
model
Configure AP group model-specific settings.
WORD
AP model name.
port-setting
Enters the config-apgrp-port context, allowing entry of commands related to port setting for the specified AP model. See port-setting for more information.
status-leds
Enable or disable the status LEDs for the specified AP model.
external-antenna
Configures external antenna settings. See external-antenna.
max-clients NUMBER
Sets the maximum clients for the AP on a per radio basis (regardless of the number of SSIDs broadcasted by the radio).
poe-out
Enable or disable the PoE Out ports for the specified AP model.
internal-heater
Enable or disable the internal heater for the specified AP model.
cband-channels
Configures the C-band (5.8 GHz) channels for the specified AP model (enable, disable). (UK country code only)
cband-license
Enable or disable 5.8 GHz Channels License for the specified AP model.
lacp-status
Enable or disable LACP status for the specified AP model.
power-mode
Sets the PoE mode for the specified AP model. Allowed values are auto, 802.3af, 802.3at, 802.3bt5, 802.3bt6, or 802.3bt7.
802.3af-txchain
Sets the 2.4GHz radio transmit chains in 802.3af PoE mode for the specified AP model. Allowed values are 1, 2, or 4.
band-scheme { 2-5 | 2-5-6 }
Sets the band operation mode (dual-band or tri-band) (supported only on AP model R670).
Modes

AP group configuration mode

Usage Guidelines

The band-scheme setting is supported only on AP model R670. The band-scheme 2-5-6 setting can be configured only if the country code supports 6 GHz.

The cband-channels setting can be configured only if the AP country code is UK.

Enter the end or exit command to save the model-specific changes for the AP group.

The no form of the command removes the configured values for the model-specific settings, reverting to the default configuration settings.

Examples

The following example configures the model-specific settings globally for all APs in the AP group.

ruckus(config-apgrp)# model R850 port-setting 
The command was executed successfully. To save the changes, type 'end' or 'exit'.
ruckus(config-apgrp-port)#
ruckus(config-apgrp)# model R610 status-leds enable
The command was executed successfully. To save the changes, type 'end' or 'exit'.
ruckus(config-apgrp)#
ruckus(config-apgrp)# model R710 power-mode auto 
The command was executed successfully. To save the changes, type 'end' or 'exit'.
ruckus(config-apgrp)#
ruckus(config-apgrp)# model R710 802.3af-txchain 1 
The command was executed successfully. To save the changes, type 'end' or 'exit'.
ruckus(config-apgrp)#
ruckus(config-apgrp)# model r670 band-scheme 2-5-6
The command was executed successfully. To save the changes, type 'end' or 'exit'.
ruckus(config-apgrp)#
History
Release version Command history
200.17 This command was modified to include the band-scheme setting.