Unleashed CLI Setup Wizard

The CLI setup wizard allows you to quickly configure your controller with basic settings using a short series of CLI commands.

To perform Unleashed setup using CLI commands, use the following procedure:

  1. When the Unleashed AP is in factory default state, associate to the "Configure.Me-xxxxxx" WLAN and connect to the Unleashed CLI using SSH (default address: 10.154.231.125), and log in using the default user name and password:
    • Please login: super
    • Password: sp-admin

    The Unleashed CLI Wizard Configuration tool starts automatically.

  2. Follow the instructions in the setup wizard to configure your Unleashed Master AP. Following are the examples.

Configure Unleashed AP in Bridge Mode - Local Wizard


Would you like to start the Setup Wizard? [yes/no]: yes

Enter the way of installation:

1. easy-deployment installation.(Warning: The configuration costs about 15 seconds to store in system, and in flash empase the device may be damaged if power-off. So please avoid rebooting device after 60 seconds if network is reachable)

2. local wizard

please enter 1 or 2:
2

Enter Administrative User Name (32 characters max) [admin]: 
admin
Enter Administrator Password (4-32 characters): 
*****
Re-enter Administrator Password (4-32 characters): 
*****

Enter System Name (32 characters max) [Ruckus-Unleashed]: 
Unleashed

Enter Country Code (or 'help' to show the list) [US]: US

Enable Mesh [yes/NO]? no

Enable Gateway Mode [yes/NO]? no

Enable Dedicated Master [yes/NO]? no

Enter WAN IP type [1]: 
     1: DHCP Mode;
     2: Manual Mode;
1

Enter Access VLAN [1]: 

Enable WLANs [YES/no]? yes

Enter Wireless LAN (ESSID, 1-32 characters) [Ruckus-Wireless 1]: 
Unleashed-SSID
Is it an Open WLAN [yes/NO]? no
Enter the WPA2 Passphrase (8-63 characters): ********
Re-enter the WPA2 Passphrase (8-63 characters): 
********

Please review the following settings:
System Name=                Ruckus-Unleashed
Administrator Name=         admin
Country Code=               US
Mesh Supported=             Disable
Gateway Mode Supported=     Disable
Dedicated Master Supported= Disable
IPv4 Mode=                  DHCP
Access VLAN=                1
WLAN ESSID=                 Ruckus-Wireless 1
Wireless Authentication=    WPA2_PSK


Done with the Setup Wizard [yes/no]? yes

Save the configuration ...  



It will take a few minutes to complete, do not power off the AP! This AP will reboot automatically. 

Welcome to Ruckus Unleashed Network Command Line Interface
ruckus>

Configure Unleashed AP in Bridge Mode - Easy Deployment Installation

Would you like to start the Setup Wizard? [yes/no]: y

Enter the way of installation:

1. easy-deployment installation.(Warning: The configuration costs about 15 seconds to store in system, and in flash empase the device may be damaged if power-off. So please avoid rebooting device after 60 seconds if network is reachable)

2. local wizard

please enter 1 or 2:
1

Enter System Name (32 characters max) [Ruckus-Unleashed]: 


System name is set as [Ruckus-Unleashed] 


Enter the umm server ip or host (63 characters max):umm_server

Enter the tag (16 characters limited, only number, alphabet, underscores(_),period(.), hyphens(-), at(@) characters are allowed ):

Easy-deployment is running now. It will take a few minutes

Welcome to Ruckus Unleashed Network Command Line Interface

Configure Unleashed AP in Dedicated Mode

Please login: super
Password: ********


Welcome to Ruckus Wireless Unleashed CLI Command Line Interface 


Would you like to start the Setup Wizard? [yes/no]: yes

Enter the way of installation:

1. easy-deployment installation.(Warning: The configuration costs about 15 seconds to store in system, and in flash empase the device may be damaged if power-off. So please avoid rebooting device after 60 seconds if network is reachable)

2. local wizard

please enter 1 or 2:
2

Enter Administrative User Name (32 characters max) [admin]: 
admin
Enter Administrator Password (4-32 characters): 
*****
Re-enter Administrator Password (4-32 characters): 
*****

Enter System Name (32 characters max) [Ruckus-Unleashed]: 
Unleashed

Enter Country Code (or 'help' to show the list) [US]: US

Enable Mesh [yes/NO]? yes

Enable Gateway Mode [yes/NO]? 

Enable Dedicated Master [yes/NO]? yes

Enter WAN IP type [1]: 
     1: DHCP Mode;
     2: Manual Mode;
1
Enter Access VLAN [1]: 1

Enable WLANs [YES/no]? 

Enter Wireless LAN (ESSID, 1-32 characters) [Ruckus-Wireless 1]: 
Dedicated-SSID
Is it an Open WLAN [yes/NO]? 
Enter the WPA2 Passphrase (8-63 characters): 
********
Re-enter the WPA2 Passphrase (8-63 characters): 
********

Please review the following settings:
System Name=                Unleashed
Administrator Name=         admin
Country Code=               US
Mesh Supported=             Enable
Gateway Mode Supported=     Disable
Dedicated Master Supported= Enable
    IPv4 Mode=              DHCP
    Access VLAN=            1
WLAN ESSID=                 Dedicated-SSID
Wireless Authentication=    WPA2_PSK


Done with the Setup Wizard [yes/no]? yes


Save the configuration ...  



It will take a few minutes to complete, do not power off the AP! This AP will reboot automatically. 

Welcome to Ruckus Unleashed Network Command Line Interface
ruckus>

Configure Unleashed AP in Gateway Mode

Please login: super
Password: ********


Welcome to Ruckus Wireless Unleashed CLI Setup Wizard 


Would you like to start the Setup Wizard? [yes/no]: yes

Enter Administrative User Name (32 characters max) [admin]: 
admin
Enter Administrator Password (4-32 characters): 
*****
Re-enter Administrator Password (4-32 characters): 
*****

Enter System Name (32 characters max) [Ruckus-Unleashed]: 
Unleashed-Gateway

Enter Country Code (or 'help' to show the list) [US]: US

Enable Mesh [yes/NO]? no

Enable Gateway Mode [yes/NO]? yes

Enter AP R720 WAN Port: 
    1: port1, eth0, UP: 
    2: port2, eth1, DOWN: 
1

Enter WAN IP type [1]: 
     1: DHCP Mode;
     2: Manual Mode;
     3: PPPOE Mode;
1

// if H350, H550 AP
Enable standby WAN port [yes/NO]? y
Enter AP H350 Standby WAN Port: 
    1: port1, eth0, UP (Primary WAN): 
    2: port2, eth1, UP: 
2
Enter standby WAN IP type [1]: 
     1: DHCP Mode;
     2: Manual Mode;
2
Enter IP Address: 10.223.55.88
Enter IP Mask:    255.255.255.0
Enter Gateway:    10.223.55.254
Enter Primary DNS Server:   10.10.10.190
Enter Secondary DNS Server: 10.10.10.105
Enter LAN & WLAN IP Address [10.106.0.1]: 
192.168.1.1
Enter LAN & WLAN IP Netmask [255.255.0.0]: 
255.255.255.0
Enter Client Starting IP Address [10.106.0.2]: 
192.168.1.2
Enter Client Ending IP Address [10.106.7.209]: 
192.168.1.200

Enter Lease Time [2]:
    1: 6 hours;
    2: 12 hours;
    3: 1 day;
    4: 2 days;
    5: 1 week;
    6: 2 weeks;

1

Enable WLANs [YES/no]? yes

Enter Wireless LAN (ESSID, 1-32 characters) [Ruckus-Wireless 1]: 
Unleashed-SSID
Is it an Open WLAN [yes/NO]? no
Enter the WPA2 Passphrase (8-63 characters): 
********
Re-enter the WPA2 Passphrase (8-63 characters): 
********

Please review the following settings:
System Name=                Unleashed-Gateway
Administrator Name=         admin
Country Code=               US
Mesh Supported=             Disable
Gateway Mode Supported=     Enable
WAN Port=                   port1 eth0 UP
IPv4 Mode=                  DHCP
LAN Port IPv4 Address Info= 192.168.1.1/255.255.255.0
Client Starting IPv4=       192.168.1.2
Client Ending IPv4=         192.168.1.200
Lease Time=                 6 hours
WLAN ESSID=                 Unleashed-SSID
Wireless Authentication=    WPA2_PSK


Done with the Setup Wizard [yes/no]? yes

Save the configuration ...  



It will take a few minutes to complete, do not power off the AP! This AP will reboot automatically. 

Welcome to Ruckus Unleashed Network Command Line Interface
ruckus>