Basic Mode Commands

In this section:

  1. cfgmgr
    Configures devices and displays status.
  2. cluster
    Provides access to cluster mode for managing the cluster and viewing its status, including operational data and system health.
  3. connect-agent
    This command is used for check the connection status between the RUCKUS Edge device and RUCKUS One.
  4. create lag
    Creates a Link Aggregation Group (LAG) by specifying a unique LAG ID.
  5. delete lag
    Deletes a Link Aggregation Group (LAG).
  6. dump-db
    Dumps the Feature Flag (FF) database and Configuration Database (CfgDB) contents into the logs.
  7. enroll-device
    Enrolls new device to the platform.
  8. feature
    Manages feature flags and allows you to enable, disable, or delete specific features.
  9. featureflag
    Manages Feature Flags (FF).
  10. lag add
    Adds a member port to an existing Link Aggregation Group (LAG).
  11. lag remove
    Removes a member port from Link Aggregation Group (LAG).
  12. logfile
    Configures the file location where Feature Flag logs are stored.
  13. logging
    Provides access to Log Manager CLI interface to configure logging settings and view the status of the logging system on the device.
  14. loglevel
    Sets the logging level for the Feature Flag (FF).
  15. log-streaming
    Manages streaming of logs to RUCKUS One.
  16. network
    Enters the network configuration mode, providing access to perform network-related configurations and diagnostic operations.
  17. nslookup
    Performs a lookup on the domain name system (DNS) for the domain name.
  18. packet-capture filter
    Configures packet capture filters on the network device.
  19. packet-capture save
    Downloads the packet capture (.pcap) file using TFTP or FTP.
  20. packet-capture start
    Starts capturing packet data into a buffer.
  21. packet-capture status
    Displays the status of the packet capture feature.
  22. packet-capture stop
    Stops capturing packet data into a buffer.
  23. ping
    Checks reachability of the device to the Internet or network manager such as RUCKUS One.
  24. reboot
    Reboot the system.
  25. rproxy
    Displays rproxy information.
  26. reset
    Resets the configuration.
  27. set resource-manager configuration
    Sets the resource manager configuration.
  28. show resource-manager information
    Displays the current resource manager configuration.
  29. set internal-network
    To set the internal network.
  30. set cfgmgr
    Configures the config manager setting to manage log configurations such as CCM log and syslog levels.
  31. set default gateway
    Configures the default gateway for your device.
  32. set dns server
    Configures or deletes the Domain Name System (DNS) server on RUCKUS Edge.
  33. set drs-address
    Sets the RUCKUS Edge device to onboard the RUCKUS One controller.
  34. set interface state
    Configures the operational state of an interface to up or down.
  35. set interface IP address
    Configures the IP address settings for the interface.
  36. start dhcp client
    Starts the Dynamic Host Configuration Protocol (DHCP) client on a network interface.
  37. stop dhcp client
    Configures or deletes the Domain Name System (DNS) server on RUCKUS Edge.
  38. show
    Displays the system information.
  39. shutdown
    Shutdown the device immediately.
  40. support-core
    Collects core-dump related information.
  41. support-export
    Exports debug related information.
  42. support-log
    Collects the log-related debug information into a filename.
  43. stats
    Displays the statistics.
  44. switch-over
    Initiates a switch-over between the active and standby nodes in a cluster.
  45. system
    Displays system information.
  46. traceroute
    Determines the path through which a RUCKUS Edge can reach another device.