Enabling an IPv6 VRRPv3 owner device

This task is performed on the device that is designated as the owner VRRP device because the IPv6 address of one of its physical interfaces is assigned as the IP address of the virtual router. For each VRRP session, there are master and backup routers, and the owner router is elected, by default, as the master router.

Note: When implementing IPv6 VRRPv3 across a network with devices from other vendors, be aware of a potential interoperability issue. RUCKUS has implemented IPv6 VRRPv3 functionality to comply with RFC 5798 and will interoperate well with other vendors that support RFC 5798.
Note: Only 16 VRRP instances are configurable on the ICX 7150 device.
  1. On the device designated as the owner VRRP device, from privileged EXEC mode, enter global configuration mode by issuing the configure terminal command. 
    device# configure terminal
  2. Before enabling IPv6 VRRP, you must globally enable IPv6 routing. 
    device(config)# ipv6 unicast-routing
  3. Globally enable IPv6 VRRP. 
    device(config)# ipv6 router vrrp
  4. Configure the Ethernet interface link for the owner device. 
    device(config-ipv6-vrrp-router)# interface ethernet 1/1/5
  5. Configure the IPv6 address of the interface. 
    device(config-if-e1000-1/1/5)# ipv6 address fd2b::2/64
  6. Assign the owner device to the virtual router ID (VRID) 2. 
    device(config-if-e1000-1/1/5)# ipv6 vrrp vrid 2
    Note: You can assign a VRID number in the range of 1 through 255.
  7. Designate this router as the VRRP owner device. 
    device(config-if-e1000-1/1/5-vrid-2)# owner
  8. Configure the VRRP version. 
    device(config-if-e1000-1/1/5-vrid-2)# version 3
  9. Assign an IPv6 link-local address to the VRID for use in the local network. 
    device(config-if-e1000-1/1/5-vrid-2)# ipv6-address fe80::768e:f8ff:fe2a:0099
  10. Assign a global IPv6 address to the VRID. 
    device(config-if-e1000-1/1/5-vrid-2)# ipv6-address fd2b::2
  11. Enable the VRRP session. 
    device(config-if-e1000-1/1/5-vrid-2)# activate

The following example configures a VRRP owner device. 

device# configure terminal
device(config)# ipv6 unicast-routing
device(config)# ipv6 router vrrp
device(config-ipv6-vrrp-router)# interface ethernet 1/1/5
device(config-if-e1000-1/1/5)# ipv6 address fd2b::2/64
device(config-if-e1000-1/1/5)# ipv6 vrrp vrid 2
device(config-if-e1000-1/1/5-vrid-2)# owner
device(config-if-e1000-1/1/5-vrid-2)# version 3
device(config-if-e1000-1/1/5-vrid-2)# ipv6-address fe80::768e:f8ff:fe2a:0099
device(config-if-e1000-1/1/5-vrid-2)# ipv6-address fd2b::2
device(config-if-e1000-1/1/5-vrid-2)# activate
Parent topic: VRRPv3