Converting from Module 2 Data Uplink to Stacking Mode on an ICX 7550 Device
Note: ICX 7550 devices cannot operate in a stack when
Module 2 is configured for data uplink. Stacking election mechanisms and all stacking
operations, including IPC communications, are blocked in data uplink mode.
Complete the following steps to convert Module 2 of an ICX 7550 device from data uplink to stacking mode.
- (Optional) Verify the configuration.
- Enter global configuration mode.
- Enter the
no slot 2 uplink-100gcommand to restore the Module 2 default mode. - Enter the
write memorycommand to save the change. - (Optional) Check the resulting configuration.
The following example shows that the configured mode and the operational mode are different, indicating that the new configuration has not yet been reloaded.
ICX-7550# show stack ***** Warning! stack is not enabled. ***** T=13m35.8: alone: standalone, D: dynamic cfg, S: static ID Type Role Mac Address Pri State Comment 1 S ICX7550-48ZP alone 28b3.7129.8856 0 local None:0 +---+ 2/1| 1 |2/2 +---+ Current stack management MAC is 28b3.7129.8856 slot 2: config stack-40g/100g, oper uplink-100g - Reload the unit to put the mode change into effect.
After the reload, the unit is returned to default stacking mode. Stacking is not enabled.
- (Optional) Verify the final configuration.
The following example shows that the default 100-Gbps stacking mode has been restored. Stacking is not enabled.
ICX-7550# show stack ***** Warning! stack is not enabled. ***** T=28m40.9: alone: standalone, D: dynamic cfg, S: static ID Type Role Mac Address Pri State Comment 1 S ICX7550-48ZP alone 28b3.7129.8856 0 local None:0 +---+ 2/1| 1 |2/2 +---+ Current stack management MAC is 28b3.7129.8856 slot 2: config = oper = stack-40g/100g All UP stack ports operate at 100G
The following example converts Module 2 on an ICX 7550 device from data uplink to default mode (stacking, with speed automatically determined from optics attached).
ICX-7550# show stack
T=2m30.1: alone: standalone, D: dynamic cfg, S: static
ID Type Role Mac Address Pri State Comment
1 S ICX7550-24F alone 0011.2233.4455 0 local None:0
+---+
2/2| 1 |
+---+
Current stack management MAC is 0011.2233.4455
slot 2: config = oper = uplink-100g
ICX-7550# configure terminal
ICX-7550(config)# no slot 2 uplink-100g
Changes require reload to take effect. Please do write memory and then reload or power cycle!!!
Slot 2 will be operating in default mode after reload.
ICX-7550(config)# exit
ICX-7550# write memory
ICX-7550# show stack
***** Warning! stack is not enabled. *****
T=13m35.8: alone: standalone, D: dynamic cfg, S: static
ID Type Role Mac Address Pri State Comment
1 S ICX7550-48ZP alone 28b3.7129.8856 0 local None:0
+---+
2/1| 1 |2/2
+---+
Current stack management MAC is 28b3.7129.8856
slot 2: config stack-40g/100g, oper uplink-100g
ICX-7550# reload
ICX-7550# show stack
***** Warning! stack is not enabled. *****
T=28m40.9: alone: standalone, D: dynamic cfg, S: static
ID Type Role Mac Address Pri State Comment
1 S ICX7550-48ZP alone 28b3.7129.8856 0 local None:0
+---+
2/1| 1 |2/2
+---+
Current stack management MAC is 28b3.7129.8856
slot 2: config = oper = stack-40g/100g
All UP stack ports operate at 100G
ICX-7550# configure terminal
ICX-7550(config)# stack enable <-- Enable and configure stacking if appropriate.
Enable stacking. This unit actively participates in stacking
ICX-7550(config)# end