Configuring an ICX 7650 Stacking Trunk on a Live System

Follow these steps to convert stacking ports on both ends of a link to a stacking trunk on an ICX 7650 production stack.
  1. (Optional) Enter the show stack command to verify stack configuration. 
    ICX7650-48ZP Router# show stack
T=20h23m43.6: alone: standalone, D: dynamic cfg, S: static
ID   Type          Role    Mac Address    Pri State   Comment                   
1  S ICX7650-48ZP  active  609c.9f52.2cd5 128 local   Ready
2  S ICX7650-48F   standby 609c.9f52.4643 128 remote  Ready

    active       standby                                                       
     +---+        +---+                                                        
 -3/3| 1 |3/1--3/1| 2 |3/3-                                                    
 |   +---+        +---+   |                                                    
 |                        |                                                    
 |------------------------|                                                    
Standby u2 - protocols ready, can failover or manually switch over
Role history: N: standalone, A: active, S: standby, M: member
U1: M->S->A, U2: A->S

Current stack management MAC is 609c.9f52.2cd5
Rear-module: config = oper = stack-40g
Stack ports are operating at 40G.
    The example shows a two-unit live stack configured in a ring with no trunks.
  2. (Optional) Enter the show running-config command for additional information on the stack. 
    ICX7650-48ZP Router# show running-config | inc stack
stack unit 1
  stack-port ethernet 1/3/1 
  stack-port ethernet 1/3/3
stack unit 2
  stack-port ethernet 2/3/1 
  stack-port ethernet 2/3/3
stack enable
stack rconsole-off
stack mac 609c.9f52.2cd5
rear-module stack-40g
    The example includes only stacking information in the show running-config command output. The output confirms that the ICX 7650 stack is operating in 40-Gbps stacking mode.
  3. Enter stack unit configuration mode. 
    ICX7650-48ZP Router# configure terminal
ICX7650-48ZP Router(config)# stack unit 1
ICX7650-48ZP Router(config-unit-1)#
  4. Enter the multi-stack-trunk command followed by the set of ports on either end of the live connection to include in the stacking trunk. 
    ICX7650-48ZP Router(config-unit-1)# multi-stack-trunk ethernet 1/3/1 to 1/3/2 and ethernet 2/3/1 to 2/3/2
SYSLOG: <14> Sep  7 19:13:52 System: Interface ethernet 1/3/2, state down 

SYSLOG: <14> Sep  7 19:13:52 System: Interface ethernet 2/3/2, state down 
T=20h25m17.5: Election, was active, no change, ID=1, pri=128, 2U(1-2), A=u1, nbr#=1 1, reason: u1: stk-po-chg, , 

SYSLOG: <14> Sep  7 19:13:52 Stack: Stack unit 1 has been elected as ACTIVE unit of the stack system 

SYSLOG: <14> Sep  7 19:13:53 System: Interface ethernet 1/3/2, state up 

SYSLOG: <14> Sep  7 19:13:53 System: Interface ethernet 2/3/2, state up 

ICX7650-48ZP Router(config-unit-1)# end
    The example configures a stacking trunk from ports 1/3/1 to 1/3/2 on one end of the connection to ports 2/3/1 and 2/3/2 on the other end.
  5. Enter the write memory command in privileged Exec mode to save the configuration. 
    ICX7650-48ZP Router(config-unit-1)# end

SYSLOG: <14> Sep  7 19:13:57 Security: running-config was potentially changed by operator from console 

ICX7650-48ZP Router# write memory

Automatic copy to member units:  2
ICX7650-48ZP Router#
SYSLOG: <14> Sep  7 19:13:59 Security: startup-config was changed by operator from console 
Flash Memory Write (8192 bytes per dot) 
.
Write startup-config done.
Copy Done.
    The example saves the 40-Gbps trunk configuration.
  6. (Optional) Enter the show stack command to confirm the formation of the trunk. 
    ICX7650-48ZP Router# show stack
T=20h24m41.8: alone: standalone, D: dynamic cfg, S: static
ID   Type          Role    Mac Address    Pri State   Comment                   
1  S ICX7650-48ZP  active  609c.9f52.2cd5 128 local   Ready
2  S ICX7650-48F   standby 609c.9f52.4643 128 remote  Ready

    active       standby                                                       
     +---+        +---+                                                        
 -3/3| 1 |3/1==3/1| 2 |3/3-                                                    
 |   +---+        +---+   |                                                    
 |                        |                                                    
 |------------------------|                                                    
Will assign standby in 47 sec due to all ready

Standby u2 - protocols ready, can failover
Role history: N: standalone, A: active, S: standby, M: member
U1: M->S->A, U2: A->S

Current stack management MAC is 609c.9f52.2cd5
Rear-module: config = oper = stack-40g
Stack ports are operating at 40G.
    The example shows a trunk is present.
Parent topic: Forming an ICX 7650 Stack