Once you have created registration
rules and the AP zones to which joining access points can be assigned automatically,
access
points will be able to join or register with the controller automatically.
After an access point registers successfully with
the controller, you can update its configuration by completing the following steps.
From the list, select the AP that
you want to configure and click Configure. The
Edit AP page is displayed.
Edit the parameters as explained in Access
Point Edit Parameters table below.
Click OK.
Note: Select the
Override check box if you want to configure new settings.
Access Point Edit
Parameters
Field
Description
Your Action
AP Configuration
> General
Options
AP
Name
Indicates the name of the AP.
Enter a name.
Description
Gives a short description of the AP.
Enter a short description.
Location
Indicates a generic location.
Select the check box and enter the location.
Location Additional Information
Indicates a specific location.
Select the check box and enter the location.
GPS
Coordinates
Indicates the geographical location.
Select the option. For the Manual option, enter the
following details:
Latitude
Longitude
Altitude
User
Location Information
Indicates the demographic information.
Enter the Area Code and Cell Identifier.
AP
Admin Logon
Indicates the administrator logon credentials.
Select the check box and enter the Logon ID and Password.
AP
Configuration > Radio
Options
Dual-5G
Mode
Enables third radio operator in 2.4 GHz, Lower 5 GHz, and Upper 5
GHz. By default, the Dual-5G
Mode is enabled. In the enabled mode, radio-0 will be on
2.4GHz band, radio-1 will be on 5G Lower band and radio-2 will be on 5G
Upper band.
5G Lower BAND :
UNII-1, UNII-2A
5G Upper BAND :
UNII-2C, UNII-3
In the disabled
mode, the radio-0 will be on 2.4GHz band, radio-1 will be on 5G band
and radio-2 will be on 6G band. This also depends on the country
code.
Select or keep the default Dual-5G
Mode option.
AP
Configuration > Band/Spectrum Configuration > 2.4
GHz
Channelization
Helps manage and allocate radio frequency resources. A lower channel width allows
the
zone to potentially serve more clients, whereas a higher channel width
improves throughput, but potentially serves fewer clients and increases
the possibility of interference. The Auto setting defaults to 20 MHz
channelization.
Set the channel bandwidth used during transmission to either 20 or 40 (MHz), or select
Auto to set it automatically.
Note: By default, for
the Country Code Indonesia, the Channelization width is set to 20 MHz only for
outdoor APs.
Channel
Indicates the channel to use.
Select one of the options: Auto, 1, 6 or 11.
Auto Cell
Sizing
Enables the AP to share information on interference seen by each
other and dynamically adjust their radio Tx power and Rx parameters to
minimize interference. Enabling this option disables the TX Power
Adjustment configuration.
Note: Ensure that
Background Scan is enabled.
Select the option.
TX Power
Adjustment
Allows to manually configure the transmit power on the 2.4 GHz radio.
By default, the TX power is set to Full on the 2.4 GHz radio.
Note: If you choose Min,
the transmit power is set to 0dBm (1mW) per chain for 11n APs, and
2dBm per chain for 11ac APs. If you choose Max, the transmit power
is set to the maximum allowable value according to the AP's
capability and the operating country's regulations.
Select the preferred TX power.
Protection
Mode
Allows to manually override the protection mode and select from the
options -
None
RTS/CTS
CTS Only
Select the preferred protection mode.
WLAN
Group
Allows to manually configure the WLAN Group. To add a WLAN group, refer to the Creating a WLAN
group section of the RUCKUS SmartZone
(LT-GA) WLAN Management Guide (SZ300/vSZ-H).
Add a WLAN group to the AP Group.
WLAN
Service
By default it is ON.
Background
Scan
Allows the AP radio to scan other channels in the band for accessing channel health
and
capacity, detecting rogue devices, optimizing and maintaining mesh links
and to discover AP neighbors.
Enter the duration in seconds. Range: 1 through 65535.
Auto Channel
Selection
Automatically adjusts the channel for network self-healing and performance
optimization.
7.0
update
ChannelFly is set as
the default option.
For the ChannelFly option,
you may also modify the default settings for the Channel
Change Frequency and Full Optimization
Period.
The Channel Change
Frequency slidebar allows you to specify the
responsiveness of ChannelFly to interference (with consideration for
the impact on associated clients), ranging from Minimal to Very
Often.
The Full Optimization Period
timeslot bar allows you to specify one or more periods of time when
ChannelFly is allowed to fully optimize the channel plan, ignoring
the impact of channel changes on associated clients. Select time
periods when the wireless network is servicing the fewest
clients.
Select the required option.
Background Scanning: Changes the AP
channel when there is an interference.
ChannelFly: Monitors potential throughput and
will change channels to learn each channel's capacity, optimize
throughput, and to avoid interference.
AP
Configuration > Band/Spectrum Configuration > 5
GHz
Channelization
Helps manage and allocate radio frequency resources. A lower channel width allows
the
zone to potentially serve more clients, whereas a higher channel width
improves throughput, but potentially serves fewer clients and increases
the possibility of interference.
7.0 update
Prior to SmartZone release 7.0.0, the
Auto setting defaulted to 80 MHz channelization. Beginning in SmartZone
release 7.0.0, the Auto setting defaults to 40 MHz
channelization.
Set the channel bandwidth used during transmission: Auto, 20, 40, 80 and 160.
Note: By default, for
the Country Code Indonesia, the Channelization width is set to 20 MHz only for
outdoor APs.
Channel
Indicates the channel to use.
Select the required options for the Indoor and Outdoor APs.
Secondary
Channel
Indicates the secondary channel to used.
By default, the Indoor and Outdoor option is set to Auto.
Allow
DFS Channels
Allows ZoneFlex APs to use DFS channels.
Click to enable the option.
Allow Channel 144
Provides channel 140
and 144 support for 11ac and 11ax APs. Enabling this option supports
20 MHz, 40 MHz, or 80 MHz channel modes. The 160 MHz mode is
supported if the AP supports this mode. Disabling this option
provides Channel 140 support only to 20 MHz mode.
Note: This option is
available for selection only if you enable the DFS
Channels option.
Note: This feature is
currently supported only in the United States.
Click to enable the option.
Allow Indoor
Channels
Allows outdoor APs to use channels regulated as for indoor use
only.
Click to enable the option.
Auto Cell
Sizing
Enables the AP to share information on interference seen by each
other and dynamically adjust their radio Tx power and Rx parameters to
minimize interference. Enabling this option disables the TX Power
Adjustment configuration.
Note: Ensure that
Background Scan is enabled.
Select the option.
TX Power
Adjustment
Allows to manually configure the transmit power on the 5 GHz radio.
By default, the TX power is set to Full on the 5 GHz radio.
Note: If you choose Min,
the transmit power is set to 0dBm (1mW) per chain for 11n APs, and
2dBm per chain for 11ac APs. If you choose Max, the transmit power
is set to the maximum allowable value according to the AP's
capability and the operating country's regulations.
Select the preferred TX power.
Protection
Mode
Allows to manually override the protection mode and select from the
options -
None
RTS/CTS
CTS Only
Select the preferred protection mode.
WLAN
Group
Allows to manually configure the WLAN Group.
Add a WLAN group to the AP Group.
WLAN
Service
By default it is ON.
Auto Channel
Selection
Automatically adjusts the channel for network self-healing and performance
optimization.
7.0
update
ChannelFly is set as
the default option.
For the ChannelFly option,
you may also modify the default settings for the Channel
Change Frequency and Full Optimization
Period.
The Channel Change
Frequency slidebar allows you to specify the
responsiveness of ChannelFly to interference (with consideration for
the impact on associated clients), ranging from Minimal to Very
Often.
The Full Optimization Period
timeslot bar allows you to specify one or more periods of time when
ChannelFly is allowed to fully optimize the channel plan, ignoring
the impact of channel changes on associated clients. Select time
periods when the wireless network is servicing the fewest
clients.
Select the required option.
Background Scanning: Changes the AP
channel when there is an interference.
ChannelFly: Monitors potential throughput and
will change channels to learn each channel's capacity, optimize
throughput, and to avoid interference.
AP
Configuration > Band/Spectrum Configuration > 6
GHz
Note: This
tab is available only if the Tri-bandDual-5G
Mode option is not enabled.
Channelization
Helps manage and allocate radio frequency resources. A lower channel width allows
the
zone to potentially serve more clients, whereas a higher channel width
improves throughput, but potentially serves fewer clients and increases
the possibility of interference.
7.0 update
The Auto setting defaults to 160 MHz
channelization.
Set the channel bandwidth used during transmission: Auto, 20, 40, 80 and 160.
Channel
Indicates the channel to use.
Select the required options for the Indoor and Outdoor APs.
Auto Cell
Sizing
Enables the AP to share information on interference seen by each
other and dynamically adjust their radio Tx power and Rx parameters to
minimize interference. Enabling this option disables the TX Power
Adjustment configuration.
Note: Ensure that
Background Scan is enabled.
Select the option.
TX Power
Adjustment
Allows to manually configure the transmit power on the 6 GHz radio.
By default, the TX power is set to Full on the 6 GHz radio.
Note: If you choose Min,
the transmit power is set to 0dBm (1mW) per chain for 11n APs, and
2dBm per chain for 11ac APs. If you choose Max, the transmit power
is set to the maximum allowable value according to the AP's
capability and the operating country's regulations.
Select the preferred TX power.
Background
Scan
Allows the AP radio to scan other channels in the band for accessing channel health
and
capacity, detecting rogue devices, optimizing and maintaining mesh links
and to discover AP neighbors.
Enter the duration in seconds. Range: 1 through 65535.
Auto Channel
Selection
Automatically adjusts the channel for network self-healing and performance
optimization.
7.0
update
ChannelFly is set as
the default option.
For the ChannelFly option,
you may also modify the default settings for the Channel
Change Frequency and Full Optimization
Period.
The Channel Change
Frequency slidebar allows you to specify the
responsiveness of ChannelFly to interference (with consideration for
the impact on associated clients), ranging from Minimal to Very
Often.
The Full Optimization Period
timeslot bar allows you to specify one or more periods of time when
ChannelFly is allowed to fully optimize the channel plan, ignoring
the impact of channel changes on associated clients. Select time
periods when the wireless network is servicing the fewest
clients.
Select the required option.
Background Scanning: Changes the AP
channel when there is an interference.
ChannelFly: Monitors potential throughput and
will change channels to learn each channel's capacity, optimize
throughput, and to avoid interference.
AP
Configuration > Band/Spectrum Configuration > Lower 5
GHz
Channelization
Helps manage and allocate radio frequency resources. A lower channel width allows
the
zone to potentially serve more clients, whereas a higher channel width
improves throughput, but potentially serves fewer clients and increases
the possibility of interference.
7.0 update
Prior to SmartZone release 7.0.0, the
Auto setting defaulted to 80 MHz channelization. Beginning in SmartZone
release 7.0.0, the Auto setting defaults to 40 MHz
channelization.
Set the channel bandwidth used during transmission: Auto, 20, 40, 80 and 160.
Note: By default, for
the Country Code Indonesia, the Channelization width is set to 20 MHz only for
outdoor APs.
Channel
Indicates the channel to use.
Select the required options for the Indoor and Outdoor APs.
Allow
DFS Channels
Allows ZoneFlex APs to use DFS channels.
Click to enable the option.
Allow Indoor
Channels
Allows outdoor APs to use channels regulated as for indoor use
only.
Click to enable the option.
Auto Cell
Sizing
Enables the AP to share information on interference seen by each
other and dynamically adjust their radio Tx power and Rx parameters to
minimize interference. Enabling this option disables the TX Power
Adjustment configuration.
Note: Ensure that
Background Scan is enabled.
Select the option.
TX Power
Adjustment
Allows to manually configure the transmit power on the Lower 5 GHz
radio. By default, the TX power is set to Full on the Lower 5 GHz
radio.
Note: If you
choose Min, the transmit power is set to 0dBm (1mW) per chain for
11n APs, and 2dBm per chain for 11ac APs. If you choose Max, the
transmit power is set to the maximum allowable value according to
the AP's capability and the operating country's
regulations.
Select the preferred TX power.
Background
Scan
Allows the AP radio to scan other channels in the band for accessing channel health
and
capacity, detecting rogue devices, optimizing and maintaining mesh links
and to discover AP neighbors.
Enter the duration in seconds. Range: 1 through 65535.
Auto Channel
Selection
Automatically adjusts the channel for network self-healing and performance
optimization.
7.0
update
ChannelFly is set as
the default option.
For the ChannelFly option,
you may also modify the default settings for the Channel
Change Frequency and Full Optimization
Period.
The Channel Change
Frequency slidebar allows you to specify the
responsiveness of ChannelFly to interference (with consideration for
the impact on associated clients), ranging from Minimal to Very
Often.
The Full Optimization Period
timeslot bar allows you to specify one or more periods of time when
ChannelFly is allowed to fully optimize the channel plan, ignoring
the impact of channel changes on associated clients. Select time
periods when the wireless network is servicing the fewest
clients.
Select the required option.
Background Scanning: Changes the AP
channel when there is an interference.
ChannelFly: Monitors potential throughput and
will change channels to learn each channel's capacity, optimize
throughput, and to avoid interference.
AP
Configuration > Band/Spectrum Configuration > Upper 5
GHz
Channelization
Helps manage and allocate radio frequency resources. A lower channel width allows
the
zone to potentially serve more clients, whereas a higher channel width
improves throughput, but potentially serves fewer clients and increases
the possibility of interference.
7.0 update
Prior to SmartZone release 7.0.0, the
Auto setting defaulted to 80 MHz channelization. Beginning in SmartZone
release 7.0.0, the Auto setting defaults to 40 MHz
channelization.
Set the channel bandwidth used during transmission: Auto, 20, 40, 80 and 160.
Channel
Indicates the channel to use.
Select the required options for the Indoor and Outdoor APs.
Allow
DFS Channels
Allows ZoneFlex APs to use DFS channels.
Click to enable the option.
Allow Channel 144
Provides channel 140
and 144 support for 11ac and 11ax APs. Enabling this option supports
20 MHz, 40 MHz, or 80 MHz channel modes. The 160 MHz mode is
supported if the AP supports this mode. Disabling this option
provides Channel 140 support only to 20 MHz mode.
Note: This option is
available for selection only if you enable the DFS
Channels option.
Note: This feature is
currently supported only in the United States.
Click to enable the option.
Auto Cell
Sizing
Enables the AP to share information on interference seen by each
other and dynamically adjust their radio Tx power and Rx parameters to
minimize interference. Enabling this option disables the TX Power
Adjustment configuration.
Note: Ensure that
Background Scan is enabled.
Select the option.
TX Power
Adjustment
Allows to manually configure the transmit power on the Upper 5 GHz
radio. By default, the TX power is set to Full on the Upper 5 GHz
radio.
Note: If you
choose Min, the transmit power is set to 0dBm (1mW) per chain for
11n APs, and 2dBm per chain for 11ac APs. If you choose Max, the
transmit power is set to the maximum allowable value according to
the AP's capability and the operating country's
regulations.
Select the preferred TX power.
Background
Scan
Allows the AP radio to scan other channels in the band for accessing channel health
and
capacity, detecting rogue devices, optimizing and maintaining mesh links
and to discover AP neighbors.
Enter the duration in seconds. Range: 1 through 65535.
Auto Channel
Selection
Automatically adjusts the channel for network self-healing and performance
optimization.
7.0
update
ChannelFly is set as
the default option.
For the ChannelFly option,
you may also modify the default settings for the Channel
Change Frequency and Full Optimization
Period.
The Channel Change
Frequency slidebar allows you to specify the
responsiveness of ChannelFly to interference (with consideration for
the impact on associated clients), ranging from Minimal to Very
Often.
The Full Optimization Period
timeslot bar allows you to specify one or more periods of time when
ChannelFly is allowed to fully optimize the channel plan, ignoring
the impact of channel changes on associated clients. Select time
periods when the wireless network is servicing the fewest
clients.
Select the required option.
Background Scanning: Changes the AP
channel when there is an interference.
ChannelFly: Monitors potential throughput and
will change channels to learn each channel's capacity, optimize
throughput, and to avoid interference.
Configuration > AP
GRE Tunnel Options
Ruckus GRE Forwarding
Broadcast
Forwards broadcast traffic from network to
tunnel.
Note: ARP and
DHCP traffic are allowed even if this option disabled
Click Override to enable the Ruckus GRE broadcast
forwarding option.
Click the Enable Forwarding
Broadcast option to forward the broadcast traffic.
AP Configuration
> AP SNMP
Options
Override zone configuration
Allows you to override the existing zone configuration
Select the check box
Enable
AP SNMP
Enables you to configure SNMP settings.
Select the check box
SNMPv2
Agent
Allows you to add users to SNMPv2 Agent.
Click Create
and enter Community.
Select the
required Privilege. If you select Notification enter the Target
IP.
Click OK.
SNMPv3
Agent
Allows you to add users to SNMPv3 Agent.
Click Create
and enter User.
Select the
required Authentication.
Enter the Auth Pass
Phrase.
Select the Privacy
option.
Select the
required Privilege. If you select Notification select the option Trap or
Inform
and enter the Target IP.
Click OK.
AP Configuration
> Model Specific
Options
Model
Specific Control
Indicates that the model overrides the AP settings.
Select the check box.
USB
Port
Disables the USB port on the selected AP model.
Select the option. USB ports are enabled by default.
Status
LEDs
Disable the status LED on the selected AP model.
Select the option.
LLDP
Enables the Link Layer Discovery Protocol (LLDP) on the
selected AP model.
Select the option and enter the following details:
Advertise
Interval—Enter the duration in seconds.
Hold
Time—Enter the duration in seconds.
Enable
Management IP TLV—Select the check box.
PoE
Operating Mode
Allows you to operate using PoE mode. For optimal LAG
performance, a power mode higher than 802.3at is recommended.
Select the option.
LACP/LAG
Aggregates multiple network interfaces into a single logical or bonded interface.
LACP
can be enabled only on two-port 11ac wave2 and 11ax APs. A minimum of
two ports must be active on AP and switch for LACP/LAG configuration.
Enabled on switch ports where the APs Ethernet cables are connected
increases the bandwidth between the AP and the switch.
Choose the option:
Keep the AP's
settings: Retains the current AP settings.
Disabled:
Disables bond configuration.
Enabled: Enables
bond configuration. Select the Bond Port
Profile from the drop-down.
Port
Settings
Indicates the port settings. This feature is not
available if the LACP/LAG feature is selected.
Select the option and choose the required LAN option.
AP Configuration
> Advanced
Options
Network
Settings
Determines the network settings.
Select the IPv4 Settings from the following:
Static-Enter the IP
Address, Network
Mask, Gateway, Primary
DNS, Secondary DNS.
Dynamic
Keep the AP's
Setting
Smart
Monitor
Indicates AP interval check and retry threshold settings.
Select the required check boxes.
Syslog
Options
Override zone
configuration
Cancels the AP zone configuration that was set previously.
Note: The Enable External
syslog server field will be available for
configuration only if this option is selected.
Select the option.
Enable
External syslog server
Enables the AP to send syslog data to the syslog server
on the network.
Select the option.
Config
Type
Allows to customize or select an external syslog server
profile.
Select the option:
Custom: Configure
the details for the AP to send syslog messages to syslog server.
Note: The IP
address format that you enter here will depend on the AP IP
mode that you selected earlier in this procedure. If you
selected IPv4 Only, enter an IPv4 address. If you selected
IPv6 Only, enter an IPv6 address.
Primary Server Address: If the primary server
goes to sends syslog messages.
Port: enter the syslog port number on the
respective servers.
Protocol: select between UDP and TCP
protocols
Secondary Server Address: If the primary server
goes down, the AP sends syslog messages to the secondary
server as backup.
Port: enter the syslog port number on the
respective servers.
Protocol: select between UDP and TCP
protocols
Event
Facility: Select the facility level that will be
used by the syslog message. Options include: Keep
Original, Local0 (default), Local1, Local2, Local3,
Local4, Local5, Local6, and Local7.
Priority: Select the lowest priority level for
which events will be sent to the syslog server. For
example, to only receive syslog messages for events with
the warning (and higher) priority, select Warning. To receive syslog messages for
all events, select All.
Send
Logs: Select the type of messages to be sent to
the syslog server. For example, General Logs, Client
Logs or All Logs.
AP External
Syslog Profile: Select the profile from the drop-down or click
Add to create a new profile.
Hotspot
2.0 version Profile
Indicates the hotspot profile that you want to assign to
the group.
Select the required option or click Create and update
the following details:
Enter the Name.
Enter the Description.
Enter the Venue
Names.
Select the Venue
Category.
Select the Type.
Enter the WLAN
Metrics.
AP
Management VLAN
Indicates the AP management VLAN settings.
Select the check box and choose the option.
Attention: For
standalone APs, set the AP Ethernet port to trunk before changing
the AP Management VLAN settings.
Client
Admission Control
Indicates the load thresholds on the AP at which it will
stop accepting new clients.
Select the check boxes and update the following details:
Min Client
Count
Max Radio
Load
Min Client
Throughput
Rogue
Classification Policy
Indicates the parameters used to classify rogue APs. This
option is available only if you enable the Rogue AP
Detectionoption.
Select the options for
rogue classification policy:
Enable the Override option and enter the Report RSSI
Threshold. Range: 0 through
100.
Enable the Override option to override the aggressiveness
of protecting the network and choose one of the following:
Aggressive
Auto
Conservative
Enable the Override option and enter the Jamming
Threshold in percentage.
Recovery SSID
Allows you to enable or disable the Recovery(Island) SSID
broadcast on the controller.
Enable Recovery SSID
Broadcast
Direct
Multicast
Indicates whether multicast traffic is sent from a wired
device, wireless device or from the network.
Select one or more of the following:
Multicast
Traffic from Wired Client
Multicast
Traffic from Wireless Client
Multicast
Traffic from Network
Test
Speed
Measures the connection performance of the AP. The option must be
enabled to run the SpeedFlex traffic test between wireless clients and
the AP.
Enable the option.
Swap
Configuration
Add
Swap-In AP
Allows to swap APs.
Select the check box and enter the Swap-in AP MAC
details.
Note:
You can also move the location of an AP or delete an AP. To do so, select the AP
from the list and click Move or Delete as
required.
A maximum of 50 APs in a specific group can
be moved from one zone to another by using an API command. APs that fail to move
return and error code indicating the failure and the AP count. Select
Administration > Help > REST
API to refer to the API command. In the SmartZone 300 Public API
Reference Guide, refer to Access Point
Configuration > Move multiple
APs.