Viewing System Information

You can access software and hardware specifics for a RUCKUS ICX switch. For software specifics, refer to the section Software versions installed and running on a device.

The following shows example displays software and hardware details for the system. 

ICX7650-48P Router# show version
  Copyright (c) Ruckus Networks, Inc. All rights reserved.
    UNIT 1: compiled on Jan 20 2022 at 08:04:05 labeled as TNR09010_b175
      (70999408 bytes) from Primary TNR09010_b175.bin (UFI)
        SW: Version 09.0.10_b175T233
      Compressed Primary Boot Code size = 1573376, Version:10.1.22T235 (tnu10122)
       Compiled on Wed Dec 13 11:14:03 2017

  HW: Stackable ICX7650-48-HPOE
==========================================================================
UNIT 1: SL 1: ICX7650-48P-L3-PREM POE 48-port Management Module
      Serial  #:EZD3350N037
      Software Package: ICX7650_BASE_L3_SOFT_PACKAGE
      Current License: l3-base
      P-ASIC  0: type B567, rev 11  Chip BCM56567_B0
==========================================================================
UNIT 1: SL 3: ICX7650-2X100G 2-port 200G Module
==========================================================================
 2000 MHz ARMv8 Cortex-A57 processor 88 MHz bus
    8 MB boot flash memory
    2 GB code flash memory
    4 GB DRAM
STACKID 1  system uptime is 95 day(s) 1 hour(s) 12 minute(s) 38 second(s)
The system started at 21:16:53 GMT+00 Thu Jan 20 2022

The system : started=cold start

The following hardware details are listed in the output of the show version command:

  • Chassis type
  • PROM type (if applicable)
  • Chassis serial number
  • Management and interface module serial numbers and ASIC types

Refer to the RUCKUS FastIron Command Reference for more information.

For a description of the software details in the output of the show version command, refer to the section Software versions installed and running on a device.

You can also view the serial number pluggable modules. If there are no pluggable modules on the device, the serial number of the fixed modules on the device is displayed. The following is an example of the show version output on an ICX 7850ICX 7850. 

device(config)#show version
  Copyright (c) Ruckus Networks, Inc. All rights reserved.
    UNIT 1: compiled on May 27 2019 at 05:17:20 labeled as TNR08091
      (61269864 bytes) from Secondary TNR08091.bin (UFI)
        SW: Version 08.0.91T233 
      Compressed Secondary Boot Code size = 1573376, Version:10.1.16T235 (tnu10116)
       Compiled on Sat May 25 15:39:48 2019
    UNIT 2: compiled on May 27 2019 at 05:17:20 labeled as TNR08091
      (61269864 bytes) from Secondary TNR08091.bin (UFI)
        SW: Version 08.0.91T233 
      Compressed Secondary Boot Code size = 1573376, Version:10.1.16T235 (tnu10116)

  HW: Stackable ICX7850-48FS
==========================================================================
UNIT 1: SL 1: ICX7850-48FS-L3-BASE 48-port Management Module
      Serial  #:FLV3334P010
      Software Package: ICX7850_L3_SOFT_PACKAGE   
      Current License: l3-prem  
      P-ASIC  0: type B873, rev 01  Chip BCM56873_A0
==========================================================================
UNIT 1: SL 2: ICX7800-8X100G 8-port 800G Module
==========================================================================
UNIT 2: SL 1: ICX7850-48F-L3-BASE 48-port Management Module
      Serial  #:FLW3332P01E
      Software Package: ICX7850_L3_SOFT_PACKAGE                   
      Current License: l3-prem  
==========================================================================
UNIT 2: SL 2: ICX7800-8X100G 8-port 800G Module
==========================================================================
2000 MHz ARM processor ARMv8 88 MHz bus
8192 KB boot flash memory
2048 MB code flash memory
3910 MB DRAM
STACKID 1  system uptime is 7 day(s) 2 hour(s) 7 minute(s) 23 second(s) 
STACKID 2  system uptime is 7 day(s) 3 hour(s) 17 minute(s) 55 second(s) 
The system started at 14:15:36 GMT+05:30 Thu May 30 2019

The system : started=warm start   reloaded=by "stack"
My stack unit ID = 1, bootup role = active

Starting with FastIron 8.0.40, there is a show version command option that specifies the version running on a single unit. The following is an example of the show versionunit1 command output on an ICX 7850. 

device(config)#show version unit 1
  Copyright (c) Ruckus Networks, Inc. All rights reserved.
    UNIT 1: compiled on May 27 2019 at 05:17:20 labeled as TNR08091
      (61269864 bytes) from Secondary TNR08091.bin (UFI)
        SW: Version 08.0.91T233 
      Compressed Secondary Boot Code size = 1573376, Version:10.1.16T235 (tnu10116)
       Compiled on Sat May 25 15:39:48 2019

  HW: Stackable ICX7850-48FS
==========================================================================
UNIT 1: SL 1: ICX7850-48FS-L3-BASE 48-port Management Module
      Serial  #:FLV3334P010
      Software Package: ICX7850_L3_SOFT_PACKAGE   
      Current License: l3-prem  
      P-ASIC  0: type B873, rev 01  Chip BCM56873_A0
==========================================================================
UNIT 1: SL 2: ICX7800-8X100G 8-port 800G Module
==========================================================================
2000 MHz ARM processor ARMv8 88 MHz bus
8192 KB boot flash memory
2048 MB code flash memory
3910 MB DRAM
STACKID 1  system uptime is 7 day(s) 2 hour(s) 7 minute(s) 29 second(s) 
The system started at 14:15:37 GMT+05:30 Thu May 30 2019
                                                                  
The system : started=warm start   reloaded=by "stack"
My stack unit ID = 1, bootup role = active

Parent topic: Basic System Management