Supported Matrix and Unsupported Models

Before upgrading to this release, check if the controller is currently managing APs, Switches or IoT devices.

APs preconfigured with the SmartZone AP firmware may be used with SZ300 or vSZ in their native default configuration. APs factory-configured with the ZoneFlex-AP firmware may be used with the controller when LWAPP discovery services are enabled.

LWAPP2SCG must be disabled on the controller if Solo APs running 104.x are being moved under controller management. To disable the LWAPP2SCG service on the controller, log on to the CLI, and then go to enable > mode > config > lwapp2scg > policy deny-all > exit. Enter Yes to save your changes.

Note: Solo APs running releases 104.x or higher are capable of connecting to both Zone Director and SmartZone platforms. If an AP is running release 104.x or later and the LWAPP2SCG service is enabled on the controller, a race condition will occur.

Important: AP PoE power modes: AP features may be limited depending on power provided via PoE. Refer to AP datasheets for more information.

Supported AP Models

This release supports the following RUCKUS AP models.

Supported AP Models

Wi-Fi 6 (802.11ax)

Wi-Fi 6E (802.11ax)

Wi-Fi 7 (802.11be)

Indoor

Outdoor

Indoor

Indoor

Outdoor

R850

T750SE

R760

R770

T670

R750

T750

R560

R670

  

R650

T350C

      

R550

T350SE

      

R350

T350D

      

R350e

        

H550

        

H350

        

The following lists the supported AP models in this SmartZone release when placed in an AP Zone that uses an older AP version.

Attention: The R730 AP must be removed from the AP Zone before upgrading the AP Zone to the AP firmware version 6.1.1 or later.
Attention: For APs that are not compatible with R7.0.0, it is essential to maintain them with AP firmware versions of R6.1, 6.1.1, and 6.1.2. The upgrade of the Zone for APs that are not supported in R6.1, 6.1.1, and 6.1.2 is not feasible.

Supported AP Models for AP Zones using older AP versions

11ax

11ac-Wave2

Note: Supported on R6.1.0, 6.1.1, and 6.1.2.

Indoor

Outdoor

T750SE

R720

T811CM

T750

R710

T710S

T350SE

R610

T710

T350D

R510

T610S

T350C

R320

T610

R850

M510

T310S

R760 (not supported on R6.1.0)

H510

T310N

R750

H320

T310D

R730

C110

T310C

R650

  

T305I

R560 (not supported on R6.1.0)

  

T305E

R550

   E510

R350

    

H550

    

H350

    
Attention: AP R310 is Wave 1 and supports WPA3 – this is the one exception, the rest of the APs that support WPA3 are 802.11ac Wave2 or 802.11ax.

Unsupported AP Models

The following lists the AP models have reached end-of-life (EoL) status and, therefore, are no longer supported in this release.

Unsupported AP Models

Unsupported AP Models

SC8800-S

SC8800-S-AC

ZF2741

ZF2741-EXT

ZF2942

ZF7025

ZF7321

ZF7321-U

ZF7341

ZF7343

ZF7343-U

ZF7351

ZF7351-U

ZF7363

ZF7363-U

ZF7441

ZF7761-CM

ZF7762

ZF7762-AC

ZF7762-S

ZF7762-S-AC

ZF7762-T

ZF7962

ZF7781CM

ZF7982

ZF7782-S

ZF7782-E

ZF7782

ZF7372-E

ZF7372

ZF7352

ZF7055

R300

R310

R700

C500

H500

R600

R500

R310

R500E

T504

T300

T300E

T301N

T301S

FZM300

FZP300

    
  1. Does not support ICX configuration. ↩
  2. FastIron 10.0.00 and later releases do not support management VLANs. ↩
Parent topic: Is My Access Point Supported by the Firmware Upgrade?