Debug Commands Q - Z

In this section:

1. restconf platform-debug-level
   Enables debugging for the RESTCONF Service Module.
2. restconf protocol-debug-level
   Enables RESTCONF management interface.
3. debug rate-limiting
   Enables port-based rate limiting debugging.
4. debug rip database
   Displays Routing Information Protocol (RIP) database events.
5. debug rip events
   Displays RIP events.
6. debug sflow
   Enables sFlow debugging.
7. debug span all_802_1d_events
   Monitors information about all the events, timers, and packets on a specific VLAN.
8. debug span config
   Monitors information about STP Bridge Protocol Data Unit (BPDU) configuration on a specific VLAN.
9. debug span timers
   Displays information about the specific STP timer events.
10. debug stacking
    Enables debugging of stacking.
11. debug stacking ipc
    Generates debugging information related to Interprocessor Communications (IPC) and remote console sessions.
12. debug stacking probe-election
    Generates debugging information related to topology discovery, election, path calculation, and so on.
13. debug stacking zero-ipc
    Generates stack zero-touch Interprocessor Communications (IPC) debug information.
14. debug stacking zero-touch
    Generates stack zero-touch provisioning debug information.
15. debug system campram
    Traces Content Addressable Memory (CAM) or Parallel Random Access Machine (PRAM) operations.
16. debug system mem-leak
    Enables memory leak detection for a specific process from bootup.
17. debug system optics
    Activates optical monitor debugging.
18. debug system poll
    Enables backplane polling.
19. debug trunk
    Enables trunk debugging.
20. debug web events
    Enables web events debugging.
21. debug webauth timers
    Enables debugging of web authentication timers.
22. debug webauth events
    Enables debugging of web authentication events.
23. show debug
    Displays all the enabled debug functions.
24. show log debug management restconf all
    Displays LogMgr debug logs for RESTCONF.

    What exactly does this command display? Is this description correct?

    .
25. show tech-support
    Displays the output of several show commands at once. The output from this command varies depending on the router configuration.
26. show tech-support acl
    Displays debugging information related to ACL configuration and counters.
27. show tech-support cluster
    Collects and displays complete debugging information related to Multi-Chassis Trunking (MCT) cluster configuration.
28. show tech-support cpu
    Displays debugging information related to CPU usage and utilization.
29. show tech-support l2
    Displays debugging information related to Layer 2 configurations.
30. show tech-support l3 ipv4-uc
    Displays debugging information related to Layer 3 IPv4 unicast configurations.
31. show tech-support l3 ipv6-uc
    Displays debugging information related to Layer 3 IPv6 unicast configurations.
32. show tech-support license
    Displays information about the license installed on the device.
33. show tech-support memory
    Displays debugging information related to memory usage and tracking.
34. show tech-support multicast
    Displays debugging information specific to Layer 2 and Layer 3 multicast configurations.
35. show tech-support packet-loss
    Displays packet statistics information that helps in debugging packet loss scenarios.
36. supportsave
    Use the supportsave utility for collecting logs from the driver, internal libraries, and firmware. The collected logs are shared with the technical support personnel for investigating issues seen on the device.
37. supportsave
    Collects logs from different modules and uploads the logs into a remote SCP or TFTP server.
38. supportsave add_cust_cmd index
    Adds a run-time executable command into the custom module at a particular index of 32 characters long (maximum of 32 characters are allowed) during the run time.
39. supportsave del_cust_cmd all
    Deletes all the custom module commands.
40. supportsave del_cust_cmd index
    Deletes a command from the custom module at a particular index during the run time.
41. supportsave info disable
    Disables the header to be displayed for all supportsave and show tech-support commands being executed on CLI.
42. supportsave info enable
    display BEGIN headers.
43. supportsave list_cust_cmd
    Displays all commands present in the custom commands list.
44. supportsave show
    Collects and displays debugging information related to stacking configurations.