| ruckusWLANTable |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.1 |
Shows the WLAN table. |
Not accessible |
| ruckusWLANEntry |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.1.1 |
Specifies each WLAN entry. |
Not accessible |
| ruckusWLANSSID |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.1.1.1 |
Specifies the name of the SSID. |
Read-Write |
| ruckusWLANBSSID |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.1.1.2 |
This attribute serves as a unique identifier within this BSS. It
corresponds to the 48-bit MAC address associated with the wireless
interface. |
Read only |
| ruckusWLANBSSType |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.1.1.3 |
Specifies the BSS type. |
Read only |
| ruckusWLANOperationalRateSet |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.1.1.4 |
This attribute defines the range of data transmission rates that the
station can use. Each octet represents a rate, with each rate falling
within the range of 2 to 127. This corresponds to data rates increasing
in increments of 500 KB/s, ranging from 1 Mb/s to 63.5 Mb/s. These rates
must be supported for data reception, as indicated in the supported
rates table. This value is included in transmitted Beacon, Probe
Request, Probe Response, Association Request, Association Response,
Reassociation Request, and Reassociation Response frames. It is used to
assess whether a BSS, with which the station wishes to synchronize, is
appropriate. It is also utilized when initiating a BSS. |
Read only |
| ruckusWLANBeaconPeriod |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.1.1.5 |
This attribute indicates the duration, in milliseconds, that a
station should utilize for scheduling the transmission of Beacons. This
value is communicated in both Beacon and Probe Response frames. |
Read only |
| ruckusWLANDTIMPeriod |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.1.1.6 |
This attribute defines the quantity of Time Units (TUs) that a
station is allowed to use when planning Beacon transmissions. This
particular value is conveyed in both Beacon and Probe Response
frames. |
Read only |
| ruckusWLANRTSThreshold |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.1.1.7 |
This attribute represents the maximum number of octets in an MPDU,
below which an RTS/CTS handshake is not required, unless RTS/CTS is
employed as a cross modulation protection mechanism. An RTS/CTS
handshake is initiated at the start of any frame exchange sequence where
the MPDU is of Data or Management type, the MPDU contains a unique
address in the Address1 field, and the MPDU’s length exceeds this
threshold. If this attribute is set to a value larger than the maximum
MSDU size, it effectively disables the RTS/CTS handshake for Data or
Management type frames transmitted by this STA. Conversely, setting this
attribute to zero enables the RTS/CTS handshake for all Data or
Management type frames transmitted by this STA. The default value for
this attribute is set to 2347. |
Read-Write |
| ruckusWLANFragmentationThreshold |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.1.1.8 |
This attribute determines the current maximum size, in octets, of the
MPDU that can be sent to the PHY. If the size of an MSDU exceeds this
attribute’s value after adding MAC headers and trailers, the MSDU will
be fragmented. An MSDU or MMPDU will be fragmented if the resulting
frame has a unique address in the Address1 field and the frame’s length
is greater than this threshold. The default value of this attribute is
the smaller of 2346 or the aMPDUMaxLength of the connected PHY, and it
should never exceed the smaller of these two values. The value of this
attribute should never be less than 256. |
Read-Write |
| ruckusWLANRadioMode |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.1.1.9 |
Specifies the radio mode. |
Read only |
| ruckusWLANChannel |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.1.1.10 |
Specifies the current operating channel. |
Read only |
| ruckusWLANWDSEnable |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.1.1.11 |
This attribute indicates whether WDS (Wireless Distribution System)
is activated or deactivated on the interface. It permits a 4-address
mode of operation for a specified WLAN interface. |
Read-Write |
| ruckusWLANAdminStatus |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.1.1.12 |
Shows the administrative status of the WLAN interface. |
Read-Write |
| ruckusWLANProtectionMode |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.1.1.13 |
This is activated when
both IEEE 802.11g and 802.11b supported clients are present on the
same network. The settings are as follows:
- None: No
protection is used.
- ctsOnly:
The Access Point (AP) will transmit a Clear to Send (CTS) frame
before sending IEEE 802.11g frames. This CTS frame will cause
IEEE 802.11b clients to remain silent.
- rtsCts:
The sender of the IEEE 802.11g frame is required to send a
Request to Send (RTS), and the responder must send a CTS before
any IEEE 802.11g frames are transmitted.
|
Read only |
| ruckusWLANName |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.1.1.14 |
Specifies the name of the WLAN. |
Read-Write |
| ruckusWLANSSIDBcastDisable |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.1.1.15 |
Setting this value to 1 results in the SSID not being broadcasted in
the beacons. |
Read-Write |
| ruckusWLANVlanID |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.1.1.16 |
Specifies the VLAN ID of the WLAN. If VLAN ID is 1, packets from this
WLAN are untagged. |
Read-Write |
| ruckusWLANRateShaper |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.1.1.17 |
This attribute controls equitable access to the network. When
activated, it limits the network traffic throughput for each network
device to the rate specified in the traffic policy. The configuration
format is in megabits per second (Mbps) for both uplink and downlink, or
it can be set to unlimited. The supported values range from 0.10Mbps to
20.00Mbps in increments of 0.25Mbps. |
Read-Write |
| ruckusWLANIGMPSnooping |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.1.1.25 |
Sets the IGMP Snooping for this WLAN. |
Read-Write |
| ruckusWLANIfIndex |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.1.1.200 |
Shows the interface index. |
Read only |
| ruckusWLANSuppDataRatesTxTable |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.2 |
The transmit bit rates that are supported by the PLCP (Physical Layer
Convergence Procedure) and PMD (Physical Medium Dependent), are
represented by a count ranging from X’02 to X’7F. This corresponds to
data rates increasing in increments of 500Kb/s, from 1 Mb/s up to 63.5
Mb/s. However, these rates are subject to the constraints of each
individual PHY (Physical Layer). |
Not accessible |
| ruckusWLANSuppDataRatesTxEntry |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.2.1 |
Shows an entry (conceptual row) in the dot11SupportedDataRatesTx
table. |
Not accessible |
| ruckusWLANSuppDataRatesTxIndex |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.2.1.1 |
Shows the index object that identifies the data rate to
access. |
Read only |
| ruckusWLANSuppDataRatesTxValue |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.2.1.2 |
The transmit bit rates, which are supported by the Physical Layer
Convergence Procedure (PLCP) and Physical Medium Dependent (PMD), are
denoted by a count ranging from X’02 to X’7F. This corresponds to data
rates that increase in increments of 500Kb/s, starting from 1 Mb/s and
going up to 63.5 Mb/s. However, these rates are subject to the
restrictions of each individual Physical Layer (PHY). |
Read only |
| ruckusWLANSuppDataRatesRxTable |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.3 |
The receive bit rates, which are supported by the Physical Layer
Convergence Procedure (PLCP) and Physical Medium Dependent (PMD), are
denoted by a count ranging from X’02 to X’7F. This corresponds to data
rates that increase in increments of 500Kb/s, starting from 1 Mb/s and
going up to 63.5 Mb/s. |
Not accessible |
| ruckusWLANSuppDataRatesRxEntry |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.3.1 |
Shows an entry (conceptual row) in thedot11SupportedDataRatesRx
table. |
Not accessible |
| ruckusWLANSuppDataRatesRxIndex |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.3.1.1 |
Shows an index object that identifies the data rate to
access. |
Read only |
| ruckusWLANSuppDataRatesRxValue |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.3.1.2 |
The bit rates for receiving data, which are supported by the Physical
Layer Convergence Procedure (PLCP) and Physical Medium Dependent (PMD),
are represented by a count that ranges from X’02 to X’7F. This
corresponds to data rates that increase in increments of 500Kb/s,
starting from 1 Mb/s and extending up to 63.5 Mb/s. |
Read only |
| ruckusWLANStatsTable |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.4 |
Shows the WLAN statistics table. |
Not accessible |
| ruckusWLANStatsEntry |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.4.1 |
This refers to each entry of WLAN statistics. |
Not accessible |
| ruckusWLANStatsSSID |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.4.1.1 |
Shows the station SSID. |
Read only |
| ruckusWLANStatsBSSID |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.4.1.2 |
Shows the WLAN BSSID. |
Read only |
| ruckusWLANStatsNumSta |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.4.1.3 |
Shows the number of associated stations. |
Read only |
| ruckusWLANStatsNumAuthSta |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.4.1.4 |
Shows the number of authenticated stations. |
Read only |
| ruckusWLANStatsNumAuthReq |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.4.1.5 |
Shows the number of authentication requests. |
Read only |
| ruckusWLANStatsNumAuthResp |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.4.1.6 |
Shows the number of authentication responses. |
Read only |
| ruckusWLANStatsNumAuthSuccess |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.4.1.7 |
Shows the number of successful authentications. |
Read only |
| ruckusWLANStatsNumAuthFail |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.4.1.8 |
Shows the number of authentication failures. |
Read only |
| ruckusWLANStatsNumAssocReq |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.4.1.9 |
Shows the number of association requests. |
Read only |
| ruckusWLANStatsNumAssocResp |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.4.1.10 |
Shows the number of association responses. |
Read only |
| ruckusWLANStatsNumReAssocReq |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.4.1.11 |
Shows the number of reassociation requests. |
Read only |
| ruckusWLANStatsNumReAssocResp |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.4.1.12 |
Shows the number of reassociation responses. |
Read only |
| ruckusWLANStatsNumAssocSuccess |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.4.1.13 |
Shows the number of successful associations. |
Read only |
| ruckusWLANStatsNumAssocFail |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.4.1.14 |
Shows the number of association failures. |
Read only |
| ruckusWLANStatsAssocFailRate |
.1.3.6.1.4.1.25053.1.1.6.1.1.1.4.1.15 |
Shows the station association fail rate: ruckusWLANStatsNumAssocFail
or ruckusWLANStatsNumAssocReq |
Read only |