-
SPX global scalar MIB objects
Last Updated
Sep 03, 2026
SPX global scalar MIB objects SPX global scalar MIB objects SPX global scalar MIB objects The following Switch Port Extender (SPX) global scalar objects are supported on the Ruckus ICX 7150, Brocade ICX 7250, Brocade ICX 7450, RUCKUS ICX 7650 or Brocade ICX 7750 devices depending on the role of the
-
RUCKUS ICX Switch Port Extender Deployment Guide
Last Updated
Sep 02, 2026
Domain with Zero-Touch and for option 3, refer to Deployment Scenario 2: Adding Units to a Ring or Linear Topology Using the SPX Interactive-Setup Utility. To use the SPX interactive-setup utility, the zero-touch utility must be disabled. SPX interactive-setup cannot be used to bring up a CB stack. Refer to the Ruckus ICX 7450, ICX 7750, and ICX 7250 Stacking Deployment Guide for information on bringing up a CB stack.
-
Using zero-touch to add PE units
Last Updated
Sep 03, 2026
Campus Fabric domain as candidate PEs. The new units must have no startup_config flash. The example shows how to enable a standalone ICX 7750 unit as the CB before adding PE units. A standalone ICX 7650 unit or a stack of ICX 7650 or ICX 7750 units acting as the CB would add PE units in the same way
-
New in This Document
Last Updated
Sep 03, 2026
of Breakout Ports A 40 Gbps breakout cable can be used on ICX 7750 standalone units and 100/40 Gbps cable can be used on ICX 7850 and ICX 7550 standalone units to break out certain 40 Gbps ports into four 10 Gbps sub-ports and 100 Gbps ports into four 25 Gbps sub-ports respectively. Refer to
-
Campus Fabric Terminology
Last Updated
Sep 03, 2026
local ports. The control bridge can consist of an ICX 7650, ICX 7750, or ICX 7850 standalone or stack. clean unit A clean unit is a device running switch/router mode that has no startup_config flash during bootup and currently has no startup_config. (That is, the write memory command has never been
-
spx cb-configure
Last Updated
Sep 03, 2026
-enable configuration is not present. The spx cb-configure command is available only when the control bridge has been enabled on an eligible router. The router must be an ICX 7650 or ICX 7750 device. In CB configuration mode, zero-touch provisioning can be enabled, and zero-touch-ports can be configured
-
bfd holdover-interval
Last Updated
Sep 03, 2026
configuration mode OSPF router VRF configuration mode OSPFv3 router configuration mode OSPFv3 router VRF configuration mode This command is supported for Ruckus ICX 7750 and ICX 7850 devices. This command is supported for ICX 7850 devices only. If the holdover timer is configured, a protocol is not
-
permit (Standard IPv4 ACLs)
Last Updated
Sep 03, 2026
0.0.0.255 in the wildcard mask format. For RUCKUS ICX 7150 and ICX 7750 devices, ACL logging is not supported for egress ACLs. For RUCKUS ICX 7150 devices, ACL logging is not supported for egress ACLs. For the log keyword to trigger a log entry, logging must be enabled with the logging enable command
-
deny (Standard IPv4 ACLs)
Last Updated
Sep 03, 2026
example, appending /24 to an IPv4 address is equivalent to specifying 0.0.0.255 in the wildcard mask format. On RUCKUS ICX 7150 and ICX 7750 devices, ACL logging is not supported for egress ACLs. For the log keyword to trigger a log entry, logging must be enabled with the logging enable command. To delete
-
bfd holdover-interval
Last Updated
Sep 03, 2026
configuration mode OSPF router VRF configuration mode OSPFv3 router configuration mode OSPFv3 router VRF configuration mode This command is supported for Ruckus ICX 7750 and ICX 7850 devices. This command is supported for ICX 7850 devices only. If the holdover timer is configured, a protocol is not