| System restarted |
Warning |
No action required. |
System was restarted. |
| Unleashed service restarted |
Warning |
No action required. |
One of the Unleashed processes was restarted. |
| System warm restarted with {reason} |
Warning |
No action required. |
System restart/reboot. |
| System cold restarted |
Warning |
Contact RUCKUS Technical Support if this
message appears frequently. |
Unleashed went through a power-cycle. |
| System interface {ifindex} linkdown,admin
status{ifadmin},adminoper{ifoper}. |
Informational |
Contact RUCKUS Technical Support if this
message appears frequently. |
Unleashed's interface (ethernet/bridge)
went down. |
| System interface {ifindex} linkup,admin
status{ifadmin},adminoper{ifoper}. |
Informational |
No action required. |
Unleashed's interface (ethernet/bridge)
came back up. |
| System restarted by administrator. |
Informational |
No action required. |
Unleashed restarted from GUI/CLI by
administrator. |
| System shutdown by administrator. |
Informational |
No action required. |
Unleashed shutdown from GUI/CLI by
administrator. |
| System upgraded. |
Informational |
No action required. |
Unleashed system upgraded to a different
software release. |
| AP patch upgraded. |
Informational |
No action required. |
A new AP model patch has been applied.
|
| SSL certificate replaced by administrator. |
Informational |
No action required. |
Unleashed's SSL certificate replaced by administrator. |
| Intermediate certificate added by
administrator. |
Informational |
No action required. |
Unleashed's intermediate certificate added by admin. |
| SSL certificate and private key replaced by
administrator for Smart Redundancy. |
Informational |
No action required. |
Unleashed's SSL certificate and private key were replaced by
administrator for Smart Redundancy. |
| Unleashed/AP RUCKUS PKI certificates installation started by
administrator. |
Informational |
No action required. |
Unleashed/AP certificate upgrade to RUCKUS PKI certificates
started. |
| Private key and SSL certificate renewed by
administrator. |
Informational |
No action required. |
Unleashed's SSL certificate and private key was renewed by
administrator. |
| Failed to install Unleashed/AP RUCKUS PKI certificates. |
Warning |
Try again. If you encounter this message frequently, contact RUCKUS
Technical Support. |
Failed to install RUCKUS PKI certificate. |
| {Unleashed}/AP RUCKUS PKI certificates successfully installed on
{Unleashed}. |
Warning |
No action required. |
Unleashed/AP certificate upgrade to RUCKUS PKI certificates
successful. |
| System configuration restored by
administrator. |
Informational |
No action required. |
Unleashed's system configuration restored by administrator. |
| System configuration restored to factory
default by administrator. |
Informational |
No action required. |
Unleashed's system default configuration restored by administrator. |
| System uses DHCP to obtain IP address. |
Informational |
No action required. |
Unleashed is using DHCP to obtain system IP address. |
| System uses Auto Configuration to obtain
IPv6 address. |
Informational |
No action required. |
Unleashed is using IPv6 auto-configuration to obtain system IP
address. |
| System IP mode is set to {ipmode}. |
Informational |
No action required. |
Unleashed system IP mode set. |
| System IP address is set to {ip}. |
Warning |
No action required. |
Unleashed system IP address was set by administrator. |
| System IP address is set to {ip}. |
Informational |
No action required. |
Unleashed system IP address was set by administrator. |
| IPv6 address of the system is set to
{ipv6}. |
Informational |
No action required. |
Unleashed system IP address (IPv6) was set by administrator. |
| System name is set to {hostname}. |
Informational |
No action required. |
Unleashed system name is set/changed. |
Admin password changed
from {ip}.
|
Informational
|
No action required.
|
Unleashed admin
password has changed.
|
Admin has completed
the Installation Wizard.
|
Informational
|
No action required.
|
Administrator has
completed the installation wizard.
|
Unleashed image has
been upgraded from {old-version} to {new-version}
|
Warning
|
No action required.
|
Unleashed image has
been upgraded from <version-1> to <version-2>.
|
Unleashed upgrade
failed rollback to {old-version}
|
Warning
|
Try again. If you encounter this message
frequently, contact RUCKUS Technical Support.
|
Unleashed image failed
to rollback to version mentioned.
|
Unleashed upgrade
failed, a system reboot is required to rollback to {old-version}
|
Warning
|
Reboot Unleashed and try again. If you encounter
this message frequently, contact RUCKUS Technical Support.
|
Unleashed image
upgrade failed, system reboot is required to rollback to version
mentioned.
|
Unleashed upgrade
failed, please try again
|
Warning
|
Try again. If you encounter this message
frequently, contact RUCKUS Technical Support.
|
Unleashed image
upgrade failed, please try again.
|
Unleashed {image}
image integrity check passed.
|
Informational
|
No action required.
|
Unleashed image
integrity check passed.
|
Unleashed {image}
image is corrupted, use Software Upgrade to repair
|
Warning
|
Try again. If you encounter this message
frequently, contact RUCKUS Technical Support.
|
Unleashed image
appears corrupted,please try software upgrade menu to repair system
to known image state.
|
Unleashed
auto-recovery successful
|
Informational
|
No action required.
|
Unleashed
auto-recovery succeeded.
|
Unleashed
auto-recovery failed
|
Critical
|
Contact RUCKUS Technical Support.
|
Unleashed
auto-recovery failed.
|
Unleashed dhcp pool is
full
|
Informational
|
Expand the DHCP pool
or remove clients from the existing pool.
|
Unleashed current DHCP
pool is full, no new clients can be admitted unless existing clients
are removed or pool is expanded.
|
Unleashed dhcp pool is
abundant
|
Informational
|
No action required.
|
Unleashed current DHCP
pool has enough entries to service clients.
|
UMM logs in from {ip}
|
Informational
|
No action required.
|
Login by UMM specified
was successful and was from IP address in message.
|
UMM logs in failure
from {ip}
|
Informational
|
Try again. If you
encounter this message frequently, contact RUCKUS Technical Support.
|
Login attempt by UMM
failed.
|
{admin} logs in from
{ip}
|
Informational
|
No action required.
|
Unleashed admin logged in from IP address
specified.
|
{admin} logs in
failure from {ip}
|
Informational
|
Try again. If you encounter this message
frequently, contact RUCKUS Technical Support.
|
Unleashed admin login
failed.
|
Unable to authenticate
{admin} from {ip} using the specified authentication server
(connection error or timeout)
|
Warning
|
Try again. If you encounter this message
frequently, contact RUCKUS Technical Support.
|
Unleashed: Unable to authenticate admin (from IP
address) using specified authentication server.
|
{admin} is locked out
for 1 hour (20 failed login attempts in 5 minutes)
|
Warning
|
Try again. If you encounter this message
frequently, contact RUCKUS Technical Support.
|
Unleashed Admin is locked out for 1 hour from
logging in.
|
{admin} logged out
from {ip}
|
Informational
|
No action required.
|
Unleashed: Admin has logged out (from IP address)
|
All clients
disconnected by admin
|
Informational
|
No action required.
|
Unleashed: All clients
disconnected by administrator.
|
Administrator
initiates an active scan from all AP's
|
Informational
|
No action required.
|
Unleashed admin
initiates a scan request for all AP's.
|
Administrator
initiates an active scan from {ap}
|
Informational
|
No action required.
|
Unleashed admin
initiates a scan request for specified AP.
|
Temporary license
{name} has expired and all features of this license are disabled
|
Critical
|
Contact RUCKUS Technical Support to acquire a
permanent license.
|
Unleashed: temp
license has expired and all features dependent on this are disabled.
|
Temporary license
{name} will expire within one day
|
Warning
|
Contact RUCKUS Technical Support to acquire a
permanent license.
|
Unleashed: temp
license will expire in 1 day.
|
Temporary license
{name} will expire within two days
|
Informational
|
Contact RUCKUS Technical Support to acquire a
permanent license.
|
Unleashed: temp
license will expire in 2 days.
|
| URL Filtering license {name} with {apnum}
APs support will expire within {days} days |
Warning
|
Contact RUCKUS Technical Support to acquire a
permanent license.
|
URL filtering license is about to expire.
|
| URL Filtering license {name} has expired |
Warning
|
Contact RUCKUS Technical Support to acquire a
permanent license.
|
URL filtering license has expired. |
Rogue DHCP server
detector enabled
|
Informational
|
No action required.
|
Unleashed: Rogue DHCP
server detector process enabled
|
Rogue DHCP server
detector disabled
|
Informational
|
No action required.
|
Unleashed: Rogue DHCP
server detector process disabled
|
Rogue DHCP server
detector detected
|
Informational
|
Locate the rogue DHCP
server and disconnect it from the network.
|
Unleashed: A rogue
DHCP server detected.
|
Rogue DHCP server
detected on {ip}
|
Critical
|
Locate the rogue DHCP
server and disconnect it from the network.
|
Unleashed: Rogue DHCP
server detected at IP address specified.
|
DHCP server enabled
with IP range from {ip-start} to {ip-end}
|
Informational
|
No action required.
|
Unleashed: DHCP server
enabled with IP range specified.
|
Failed to enable DHCP
server
|
Warning
|
Recheck your DHCP
server settings.
|
Failed to enable DHCP
server.
|
DHCP server disabled
|
Informational
|
No action required.
|
Unleashed: DHCP server
disabled.
|
UMM management enabled
from {url}
|
Informational
|
No action required.
|
Unleashed: UMM
management enabled from specified URL.
|
UMM management
disabled
|
Informational
|
No action required.
|
Unleashed: UMM
management disabled.
|
SNMP agent v2c enabled
with RO-community {ro-community} and RW-community {rw-community}
|
Informational
|
No action required.
|
Unleashed: SNMP agent
version 2 enabled with Read-Only community and Read-Write community
specified.
|
SNMP agent v2c and v3
disabled
|
Informational
|
No action required.
|
Unleashed: SNMP agent
version 2 and version 3 disabled
|
SNMP v2 Trap enabled
with server {trap-ip}
|
Informational
|
No action required.
|
Unleashed: SNMP
version 2 Trap enabled with server IP specified
|
SNMP v2c and v3 Trap
disabled
|
Informational
|
No action required.
|
Unleashed: SNMP
version 2 and version 3 Trap disabled
|
Set AP management VLAN
to {vlan} by admin from {ip}
|
Informational
|
No action required.
|
Unleashed: AP
management VLAN was set by admin from IP address specified.
|
AP management VLAN
setting disabled by admin from {ip}
|
Informational
|
No action required.
|
Unleashed: AP
management VLAN setting was disabled by admin from IP address
specified.
|
AP management VLAN
enabled with AP settings by admin from {ip}
|
Informational
|
No action required.
|
Unleashed: AP
management VLAN enabled with AP settings by administrator from IP
address specified.
|
Unleashed management
VLAN enabled with {vlan} by admin from {ip}
|
Informational
|
No action required.
|
Unleashed: Unleashed
management VLAN enabled with VLAN by admin from IP address
specified.
|
Unleashed management
VLAN disabled by admin from {ip}
|
Informational
|
No action required.
|
Unleashed: Unleashed
management VLAN disabled by admin from IP address specified.
|
Admin from {ip} change
to provision all AP's with primary Unleashed {ip1} and secondary
Unleashed {ip2}
|
Informational
|
No action required.
|
Unleashed:
Administrator provisioned all AP's with primary Unleashed [IP] and
secondary Unleashed [IP]
|
Admin from {ip} change
to provision all AP's with primary Unleashed {ip1}
|
Informational
|
No action required.
|
Unleashed:
Administrator provisioned all AP's with primary Unleashed IP
address.
|
Admin from {ip} remove
AP's primary and secondary Unleashed settings
|
Informational
|
No action required.
|
Unleashed:
Administrator removed AP's primary and secondary Unleashed settings
|
Additional management
interface {ip} created
|
Informational
|
No action required.
|
Unleashed: Additional
management interface with IP address specified was created
|
Additional management
interface {ip} removed
|
Informational
|
No action required.
|
Unleashed: Additional
management interface with IP address specified was removed.
|
Additional management
interface {ip} updated
|
Informational
|
No action required.
|
Unleashed: Additional
management interface with IP address specified was updated.
|
Additional IPV6
management interface {ipv6} created
|
Informational
|
No action required.
|
Unleashed: Additional
IPV6 management interface specified was created.
|
Additional IPV6
management interface {ipv6} removed
|
Informational
|
No action required.
|
Unleashed: Additional
IPV6 management interface specified was removed.
|
Additional IPV6
management interface {ipv6} updated
|
Informational
|
No action required.
|
Unleashed: Additional
IPV6 management interface specified was updated.
|
Smart Redundancy is
{type}
|
Informational
|
No action required.
|
Unleashed: Smart
Redundancy is enabled or disabled.
|
[Smart Redundancy]
Peer Device IP Address changed by Administrator
|
Informational
|
No action required.
|
Unleashed:Ip Address
of active OR standby Unleashed has been changed by administrator.
|
[Smart Redundancy]
Shared Secret changed by Administrator
|
Informational
|
No action required.
|
Unleashed: Smart
Redundancy Shared Secret (required to establish SR Connection )
changed by Administrator
|
{admin} tried to
perform an unauthorized task
|
Informational
|
Try again. If you encounter this message
frequently, contact RUCKUS Technical Support.
|
Unleashed:
Administrator does not have permission to perform this task.
|
Enable remote syslog
with server {srvip} by admin from {ip}
|
Informational
|
No action required.
|
Unleashed:
Administrator has enabled the remote logging of syslog message.
|
Disable remote syslog
by admin from {ip}
|
Informational
|
No action required.
|
Unleashed:
Administrator has disabled the remote logging of syslog message.
|
SpeedFlex service is
disabled by {username} from {ip}
|
Informational
|
No action required.
|
SpeedFlex service
disabled.
|
SpeedFlex service is
enabled by {username} from {ip}
|
Informational
|
No action required.
|
SpeedFlex service
enabled.
|
SNMP request from
user-name {user-name} failed authentication
|
Critical
|
Try again. If you encounter this message
frequently, contact RUCKUS Technical Support.
|
SNMP authentication
failed when initiated by {user-name}
|
SNMP agent v3 enabled,
register user {v3-user-name} with role of {v3-user-role}
|
Informational
|
No action required.
|
snmpv3 agent enabled.
|
SNMP agent started:
v2c {v2-eanble},v3 {v3-enable}
|
Informational
|
No action required.
|
snmpv3 and v2c agents
started.
|
SNMP v3 Trap enabled
with server {trap-ip} security user {name}
|
Informational
|
No action required.
|
snmpv3 trap is
enabled. Unleashed will sent notification to SNMP server.
|
System is recovered
from failure
|
Critical
|
No action required.
|
System is recovered
from some process failure...
|
Bonjour service
enabled
|
Informational
|
No action required.
|
Bonjour service has
been enabled.
|
Bonjour service
disabled
|
Informational
|
No action required.
|
Bonjour service has
been disabled.
|
Enable Telnet service
|
Informational
|
No action required.
|
Unleashed:
Administrator has enabled Telnet service on Unleashed.
|
Bonjour service is
disabled when Bonjour Gateway is enabled
|
Informational
|
No action required.
|
Bonjour service
disabled when Bonjour Gateway enabled.
|
Disable Telnet service
|
Informational
|
No action required.
|
Unleashed:
Administrator has disabled Telnet service on Unleashed.
|
LBS Unleashed sent
Start {cn} Location Service: apgroup={apg-name}, venue={venue}
|
Informational
|
No action required.
|
Location service
enabled.
|
MSG_admin_disable_location=LBS Unleashed sent Stop {cn} Location
Service: apgroup={apg-name}, venue={venue}
|
Informational
|
No action required.
|
Location service
disabled.
|
MSG_lbs_Unleashed_LS_connection_up=LBS the connection becomes up
between Unleashed and LS: url={ls-url}, port={ls-port}
|
Informational
|
No action required.
|
Location service
connection is up.
|
MSG_lbs_Unleashed_LS_connection_down=LBS the connection becomes
down between Unleashed and LS: url={ls-url}, port={ls-port},
reason={down-reason}
|
Informational
|
No action required.
|
Location service
connection is down.
|
MSG_lbs_receive_cmd_footfall=LBS Unleashed receives passive
tracking footfall command: parameters={parameters}
|
Informational
|
No action required.
|
Unleashed receives
passive tracking footfall command.
|
MSG_lbs_receive_cmd_calibration=LBS Unleashed receives passive
tracking calibration command: parameters={parameters}
|
Informational
|
No action required.
|
Unleashed receives
passive tracking calibration command.
|
MSG_lbs_no_response_from_LS=LBS Unleashed did not receive response
from LS: url={ls-url}, port={ls-port}
|
Informational
|
No action required.
|
Unleashed did not
receive response from LS.
|
MSG_lbs_bridge_auth_failed=LBS Unleashed-LS authentication failed:
url={ls-url}, port={ls-port}
|
Informational
|
No action required.
|
Unleashed-LS
authentication failed.
|
MSG_lbs_connection_dropped=LBS Unleashed-LS connection dropped:
url={ls-url}, port={ls-port}
|
Informational
|
No action required.
|
Unleashed-LS
connection dropped.
|
Mesh name changed by
admin from {ip}
|
Informational
|
No action required.
|
Mesh SSID has been
changed by admin.
|
Mesh passphrase
changed by admin from {ip}
|
Informational
|
No action required.
|
Mesh passphrase
changed by admin from IP(address).
|
Enable global client
isolation by admin from {ip}
|
Informational
|
No action required.
|
Enabling of global
client isolation by admin from IP (address).
|
Disable global client
isolation by admin from {ip}
|
Informational
|
No action required.
|
Disabling of global
client isolation by admin at IP(address).
|
Enable mesh packet
forwarding filter by admin from {ip}
|
Informational
|
No action required.
|
Admin has enabled mesh
packet forwarding filter.
|
Disable mesh packet
forwarding filter by admin from {ip}
|
Informational
|
No action required.
|
Admin has disabled
mesh packet forwarding filter.
|
Modify rules of mesh
packet forwarding filter by admin from {ip}
|
Informational
|
No action required.
|
Admin has modified
mesh packet forwarding filter.
|
Enable ARP broadcast
filter with rate limiting threshold {range} by admin from {ip}
|
Informational
|
No action required.
|
Admin has enabled the
AP to limit the ARP broadcast on network. This will help reduce
flooding of ARP packets on network.
|
Disable ARP broadcast
filter by admin from {ip}
|
Informational
|
No action required.
|
Enable ARP broadcast
filter with rate limiting threshold
|
{authsvr} modified by
admin from {ip}
|
Informational
|
No action required.
|
Authentication server
(Radius Server) details is modified by admin.
|
{authsvr} created by
admin from {ip}
|
Informational
|
No action required.
|
Authentication server
(Radius Server) details is added by admin.
|
{authsvr} deleted by
admin from {ip}
|
Informational
|
No action required.
|
Authentication server
(Radius Server) details is deleted by admin.
|
all AAA servers RADIUS
statistics recorded {period} are reseted from {ip}
|
Informational
|
No action required.
|
All Radius statistics
reset by user.
|
AAA server {svr-name}
RADIUS statistics recorded {period} are reseted from {ip}
|
Informational
|
No action required.
|
Radius statistics for
specific server reset by user.
|
AAA server {svr-name}
{role} RADIUS statistics recorded the AAA server {svr-name} {svr-ip}
RADIUS statistics recorded {period} are reseted from {ip}{period}
are reseted from {ip}
|
Informational
|
No action required.
|
Radius statistics for
specific Radius server and specific time period reset by user.
|
all WLANs RADIUS
statistics recorded {period} are reseted from {ip}
|
Informational
|
No action required.
|
All WLANs Radius
statistics for a specific time period reset by user.
|
WLAN {wlan-name}
RADIUS statistics recorded {period} are reseted from {ip}
|
Informational
|
No action required.
|
Specific WLAN Radius
statistics for a specific time period reset by user.
|
{user-name} from {ip}
failed to log in for guest pass generation
|
Informational
|
No action required.
|
Login for guest pass
generation is failed.
|
{user-name} from {ip}
failed to log in for wireless access provisioning
|
Informational
|
No action required.
|
User login from IP
address specified failed.
|
{user} from {ip}
failed to log in. No permission or incorrect credentials.
|
Informational
|
No action required.
|
User login failed due
to lack of permission or incorrect credentials.
|
{user} failed to log
in. No permission or incorrect credentials.
|
Informational
|
No action required.
|
User login failed due
to lack of permission or incorrect credentials.
|
Unable to authenticate
{user-name} from {ip} using the specified authentication server
(connection error or timeout)
|
Warning
|
Try again. If you encounter this message
frequently, contact RUCKUS Technical Support.
|
User authentication
failed from radius server specified. Check the user name and
password.
|
Radius server {server}
has not responded to multiple requests. {reason}.
|
Warning
|
Check the RADIUS
server settings.
|
Radius server has not
responded to multiple requests. Check if the radius server is up or
not. Capture the packets at radius server to verify whether server
is receiving the request message.
|
| {user} from {wlan} at {ap} failed to verify
the access token for {oauth-server}, detail error: {err-msg} |
Warning |
Check user social media login credentials. |
Error message detailing OAuth social media
login failure. |
| {user} from {wlan} at {ap} failed to match
the host domain for {oauth-server}, detail error: {err-msg} |
Warning |
Check user social media login credentials. |
Error message detailing OAuth host domain
login failure. |
Registering wlan
{guestsvc-name} to Facebook.
|
Informational
|
No action required.
|
WLAN registration with
facebook.com started.
|
Register wlan
{guestsvc-name} to Facebook success.
|
Informational
|
No action required.
|
WLAN registration with
facebook.com successful.
|
Register wlan
{guestsvc-name} to Facebook failed.
|
Warning
|
Retry. Ensure
connectivity to facebook.com
|
WLAN registration with
facebook.com failed.
|
Please click "here"
below "Facebook WiFi" to configure settings on Facebook.com
|
Informational
|
Facebook settings have
not yet been configured.
|
Click the "Configure"
button on the side of "Facebook" Social Media Login to configure
settings on Facebook.com.
|
The maximum number of
Facebook WiFi profiles in one {Unleashed} is {num}.
|
Warning
|
Reduce the number of
Facebook WiFi profiles and try again.
|
Facebook WiFi profiles
not created because the max number of Facebook WiFi profiles has
been reached.
|
Receive reauth
response from Facebook failed, need to delete all stations in this
request.
|
Warning
|
No action required.
|
No reauthorization
response received from Facebook.com. All stations in this request
will be deleted.
|
Delete User{sta-mac}
from {wlan} at {ap} due to facebook WiFi wlan time out.
|
Warning
|
No action required.
|
Facebook WiFi user
timeout; station deleted.
|
{user} from {ip}
approved for guest access (guest pass was generated by {created-by})
|
Informational
|
No action required.
|
User from IP (address)
has been approved for guest access.
|
Guest from {ip}
approved for guest access
|
Informational
|
No action required.
|
User has been approved
for guest access.
|
There is no credit,
please recharge your account.
|
Informational
|
Recharge your account.
|
Credit exhausted,
recharge your account.
|
{ap} is assigned to
{apgroup}
|
Warning
|
No action required.
|
AP is moved to a
specified AP group.
|
{ap} initial
provisioning {apgroup} is undefined; AP assigned to system default
group
|
Warning
|
No action required.
|
AP group specified not
found, hence default AP group has been assigned.
|
{ap} joins with uptime
{uptime} s
|
Warning
|
No action required.
|
AP Joined Unleashed
with uptime specified in secs.
|
{ap} joins with uptime
{uptime} s and last disconnected reason {reason}
|
Warning
|
No action required.
|
AP Joined Unleashed
with uptime secs and last disconnected reason Heartbeat
loss/application reboot/power cycle/Release AP Cmd/reset button/
|
{ap} fails to join
|
Warning
|
Factory reset the AP
and try again.
|
AP fails to join
Unleashed. Trying factory reset of AP may enable it to join
Unleashed.
|
Model{model} is not
supported; connection request from {ap} refused
|
Warning
|
This AP model is not
supported with this version of Unleashed. Downgrade Unleashed to a
version that supports this AP model, or upgrade AP to a supported
model."
|
AP model unsupported.
Unleashed refused connection request.
|
| Discover request from {ap} is ignored for
unsupported model {model} or image |
Warning |
Upgrade or apply a new AP model patch to
support the new AP. |
Discover request from AP was ignored due to
unsupported AP model or firmware image. |
Discover request from
{ap} refused; AP limit reached.
|
Warning
|
Delete APs from the
list to allow new APs to join.
|
Discover request from
AP failed since AP limit has been reached.
|
Connection request
from {ap} refused; AP limit reached.
|
Warning
|
Delete APs from the
list to allow new APs to join.
|
Connection request
from AP failed since AP limit has been reached.
|
| Connection request from {ap} is refused;AP
limit reached in URL Filtering license. |
Warning
|
Increase URL filtering license AP limit or
reduce number of APs. |
AP connection request refused because URL
filtering license AP limit has been reached. |
| {num} AP's URL Filtering licenses are needed
to enable this feature. Please purchase and renew, and then try again. |
Warning
|
Upgrade URL filtering license to use this
feature. |
URL filtering license is needed to enable
this feature. |
| No valid license here. Please purchase and
renew, and then try again. |
Warning
|
Upgrade URL filtering license to use this
feature. |
URL filtering license is needed to enable
this feature. |
Connection request
from {ap} refused; country code mismatch.
|
Warning
|
Set the AP country
code to the same code used by Unleashed and try again.
|
Connection request
failed from AP, due to country code mismatch.
|
{ap} Configuration
update request failed.
|
Critical
|
Verify connectivity
between AP and Unleashed.
|
AP request for
configuration update failed.
|
Hardware problem
detected during {ap} attempt to join {reason}.
|
Critical
|
Contact RUCKUS Technical Support.
|
Unleashed discovered
number of radio supported on AP is ZERO, so join failed.
|
{ap} heartbeats lost
|
Warning
|
If you encounter this message frequently, contact
RUCKUS Technical Support.
|
AP has not received
echo(heartbeat) response from Unleashed.
|
Lost contact with {ap}
|
Critical
|
Check the AP uplink
connection (wired or mesh).
|
Unleashed is getting
Ping request from AP.
|
| {user} |
Informational
|
No action required. |
All user PII data has been removed. |
{ap} cold boot
successfully
|
Informational
|
If you encounter this message frequently, contact
RUCKUS Technical Support.
|
Power Cycle boot.
|
{ap} warm boot
successfully,last reboot reason {reason}.
|
Informational
|
No action required.
|
Reboot command from AP
CLI.
|
{ap}'s CPU utilization
exceeds threshold.
|
Warning
|
If you encounter this message frequently, contact
RUCKUS Technical Support.
|
AP's CPU utilization
exceeds normal thresholds.
|
{ap}'s Memory
utilization exceeds threshold.
|
Warning
|
If you encounter this message frequently, contact
RUCKUS Technical Support.
|
AP's Memory
utilization exceeds normal thresholds.
|
{ap}'s CPU clear
warning that cpu utilization is too high.
|
Warning
|
No action required.
|
AP's CPU is getting
overloaded, service may be impacted.
|
{ap}'s MEM clear
warning that mem utilization is too high.
|
Warning
|
No action required.
|
AP's memory
utilization is getting overloaded, service may be impacted.
|
{ap}'s online client
number is {value} which exceeds threshold(
|
Informational
|
No action required.
|
Number of clients on
AP have exceeded threshold limits indicating AP is getting
overloaded.
|
{ap} can not support
DFS channel {channel}.
|
Warning
|
Set channels to
non-DFS channels.
|
AP does support DFS
channel specified.
|
{ap} can not support
C-Band channel {channel}.
|
Warning
|
No action required.
|
AP does not support
C-Band channels (149 – 161).
|
{ap} download USB
Software Package Vendor-ProdID-Version {vid_pid} failed.
|
Warning
|
If you encounter this message frequently, contact
RUCKUS Technical Support.
|
USB software package
download failed.
|
{ap} downloaded USB
Software Package Vendor-ProdID-Version {vid_pid} successfully.
|
Informational
|
No action required.
|
USB software package
download was successful.
|
the USB Software
Package Vendor-ProdID-Version {vid_pid} on {ap} is overridden.
|
Informational
|
No action required.
|
USB software package
overriden successfully.
|
{ap} state set to
{new-state} with downlink {downlink-state}
|
Informational
|
No action required.
|
AP in new state
<state> with downlink <state>. AP could be failing to
join due to incorrect configuration. Remove its record from the
system.
|
{ap} state set to
{new-state} on channel {channel-radio} with downlink
{downlink-state}
|
Informational
|
No action required.
|
AP new state
(RAP/ISLAND/MAP WAITING/MAP/e-MAP/Down/(Mesh/eMesh Forming), on
channel <xx> with down link Enabled/Disabled.
|
{ap} state set to
{new-state} uplinks to {meshap} across {hops} hops with downlink
{downlink-state}
|
Informational
|
No action required.
|
AP new state
(RAP/ISLAND/MAP WAITING/MAP/e-MAP/Down/(Mesh/eMesh Forming), on
channel <xx> with down link Enabled/Disabled.
|
{ap} state set to
{new-state} uplinks to {meshap} across {hops} hops on channel
{channel-radio} with downlink {downlink-state}
|
Informational
|
No action required.
|
AP new state
(RAP/ISLAND/MAP WAITING/MAP/e-MAP/Down/(Mesh/eMesh Forming), uplink
to mesh AP(name) with number of hops on channel <xx> with down
link Enabled/Disabled.
|
Mesh {ap} connects to
Mesh {meshap} with RSSI {rssi} across {mesh-depth} links
|
Informational
|
No action required.
|
Mesh AP connected to
another Mesh AP with RSSI <x> and hops <y>
|
Mesh {ap} connects to
Root {rootap} with RSSI {rssi} across {mesh-depth} links
|
Informational
|
No action required.
|
Mesh AP connected to
Root AP with RSSI <rssi> and hops <x>
|
Mesh {ap} accepts Mesh
{meshap} connection
|
Informational
|
No action required.
|
Mesh AP accepted
connection from another Mesh AP
|
Root {ap} accepts Mesh
{meshap} connection
|
Informational
|
No action required.
|
Root AP accepted
connection from another Mesh AP
|
Mesh {meshap} fails to
connect to {ap} (authentication invalid)
|
Informational
|
Check the
authentication settings on the uplink AP.
|
Mesh AP failed
authenticating to Root AP
|
Mesh {meshap}
disconnects from {ap}
|
Informational
|
If you encounter this message frequently, contact
RUCKUS Technical Support.
|
Mesh AP disconnected
from Root AP
|
Mesh {ap} disconnects
from uplink {meshap}
|
Critical
|
If you encounter this message frequently, contact
RUCKUS Technical Support.
|
Mesh AP disconnected
from uplink Mesh AP
|
Isolated Mesh {ap}
detected
|
Informational
|
See User Guide for
instructions on isolated Mesh AP recovery.
|
Isolated /unconnected
Mesh AP detected
|
eMesh {ap} connects to
Mesh {meshap} across {mesh-depth} links {rea}
|
Critical
|
No action required.
|
eMesh AP connected to
Mesh AP across hops <x>
|
Mesh {ap} connects to
eMesh {linkap} with RSSI {rssi} across {mesh-depth} links {rea}
|
Critical
|
No action required.
|
Mesh AP connected to
eMesh AP with RSSI <rssi> across hops <x>
|
Mesh {ap} accepts
eMesh {linkap} connection
|
Informational
|
No action required.
|
Mesh AP accepted
connection from eMesh AP
|
eMesh {ap} accepts
Mesh {meshap} connection
|
Informational
|
No action required.
|
eMesh AP accepted
connection from Mesh AP
|
eMesh {ap} disconnects
from uplink Mesh {meshap}
|
Critical
|
Check the connection
to the uplink AP.
|
eMesh AP disconnected
from uplink Mesh AP
|
Mesh {ap} disconnects
from uplink eMesh {linkap}
|
Critical
|
Check the connection
to the uplink AP.
|
Mesh AP disconnected
from uplink eMesh AP
|
eMesh {linkap}
disconnects from Mesh {ap}
|
Critical
|
Check the connection
to the uplink AP.
|
eMesh AP disconnected from Mesh AP specified
|
Mesh {meshap}
disconnects from eMesh {ap}
|
Critical
|
Check the connection
to the uplink AP.
|
Mesh AP disconnected
from eMesh AP specified.
|
{ap} accepts Mesh
{meshap} with {hops} hops (hop count exceeds the threshold
{threshold} hops).
|
Warning
|
Place more wired APs
to reduce the number of hops.
|
Root AP accepted
connection from Mesh AP - but hop count exceeded
|
{ap} accepts Mesh
{meshap} and current AP's downlinks {fanout} exceeds threshold
{threshold}.
|
Warning
|
Place more wired APs
to reduce the number of hops.
|
Root AP accepted
connection from Mesh AP - but downlink hop count exceeded
|
{ap} deleted by
administrator
|
Informational
|
No action required.
|
AP deleted by Admin
|
{ap} restarted by
administrator
|
Informational
|
No action required.
|
AP restated by Admin
|
{ap} is removed from
Unleashed for Migration by administrator
|
Warning
|
No action required.
|
AP removed by Admin
for migration.
|
{ap} released by
administrator
|
Warning
|
No action required.
|
AP released by Admin
|
{ap} reset to factory
default by administrator
|
Informational
|
No action required.
|
AP reset to factory
default by administrator
|
{ap} reset to enable
mesh function
|
Informational
|
No action required.
|
AP has been reset to
enable mesh function
|
{ap} reset to disable
mesh function
|
Warning
|
No action required.
|
AP has been reset to
disable mesh function
|
{ap} reset due to
country code change
|
Informational
|
No action required.
|
AP reset due to
country code change
|
{ap} reset due to
channel compatibility change
|
Informational
|
No action required.
|
AP reset due to
channel compatibility change
|
{ap} reset due to
management vlan change
|
Informational
|
No action required.
|
AP reset due to
management vlan change
|
{ap} reset due to
valid work time expired
|
Warning
|
No action required.
|
AP reset due to valid
work time expiration
|
{ap} reset due to IP
address change
|
Warning
|
No action required.
|
AP reset due to IP
address change
|
{ap} radio band change
from {ori_band} to {new_band}
|
Warning
|
No action required.
|
AP radio band change
occurred
|
{ap} reset due to
radio band change from {ori_band} to {new_band}
|
Warning
|
No action required.
|
AP radio band change
occurred
|
{ap} joins with radio
band {ap-band}, set to {Unleashed-band}
|
Warning
|
No action required.
|
AP radio band change
occurred
|
{ap} reset due to mesh
mode change
|
Warning
|
No action required.
|
AP reset due to mesh
mode change
|
{ap} reset due to WLAN
migration
|
Warning
|
No action required.
|
AP reset due to WLAN
migration
|
The IP type of {ap} is
PPPoE, which does not support mesh.
|
Warning
|
Set the AP IP type to
non-PPPoE.
|
The IP type of AP is
PPPoE, which does not support mesh
|
{ap} reset because its
configuration is out of sync with Unleashed
|
Informational
|
No action required.
|
AP reset because its
configuration is out of sync with Unleashed
|
A new {ap} requests to
join and is automatically approved
|
Informational
|
No action required.
|
AP requests to join
and is automatically approved
|
A new {ap} requests to
join, pending approval of administrator
|
Warning
|
Approve the AP join
request.
|
AP requests to join,
pending approval of administrator
|
{ap} fails to join
because of incorrect configuration; unable to authenticate this AP.
|
Warning
|
Factory reset the AP
and allow it to rejoin.
|
AP fails to join
because of incorrect configuration; unable to authenticate this AP.
|
An previously known
{ap} fails to join due to incorrect configuration. Remove its record
from the system.
|
Warning
|
Delete the AP from the
AP list and allow it to rejoin.
|
A previously known AP
fails to join due to incorrect configuration. Remove its record from
the system.
|
An {ap} fails to join
because uplink Mesh {meshap} not found.
|
Warning
|
Check the status of
the uplink Mesh AP.
|
AP fails to join
because uplink Mesh AP not found.
|
Allow {ap} to join and
its uplink {meshap} is not found.
|
Warning
|
Check the status of
the uplink Mesh AP.
|
AP was allowed to join
but its uplink AP is not found.
|
{ap} detects
interference on radio {radio} and switches from channel
{from-channel} to channel {to-channel}.
|
Informational
|
No action required.
|
AP detects
interference on radio band and switches channels
|
Provision {ap} with
primary Unleashed {primary-ip}
|
Warning
|
No action required.
|
AP is provisioning
with primary Unleashed
|
Provision {ap} with
primary Unleashed {primary-ip} and AP Group {group}
|
Warning
|
No action required.
|
AP is provisioning
with primary Unleashed in specific AP Group
|
Provision {ap} with
primary Unleashed {primary-ip} and secondary Unleashed
{secondary-ip}
|
Warning
|
No action required.
|
AP is provisioning
with primary and secondary Unleasheds
|
Provision {ap} with
primary Unleashed {primary-ip}, secondary Unleashed {secondary-ip}
and AP Group {group}
|
Warning
|
No action required.
|
AP is provisioning
with primary and secondary Unleasheds in specific AP group
|
{ap} has been moved to
primary Unleashed {primary-ip}
|
Warning
|
No action required.
|
AP has been moved to
primary Unleashed
|
{ap} has been moved to
primary Unleashed {primary-ip} and secondary Unleashed
{secondary-ip}
|
Warning
|
No action required.
|
AP moved to primary
Unleashed and secondary Unleashed
|
Delete {ap} move-ap
action
|
Warning
|
No action required.
|
No information
available.
|
{ap} has moved to
primary Unleashed {primary-ip}
|
Warning
|
No action required.
|
AP has been moved to
primary Unleashed
|
{ap} has incomplete
primary addr/secondary addr settings when Unleashed keeps AP's
primary and secondary addresses settings.
|
Informational
|
Check the
primary/secondary Unleashed address settings on the AP, or configure
Limited Unleashed Discovery to not keep AP's primary/secondary
address settings.
|
AP has incomplete
primary and secondary address settings from the Unleashed
|
The Channelfly {ap}
detects interference on radio {radio} and switches from channel
{from-channel} to channel {to-channel}.
|
Informational
|
No action required.
|
The ChannelFly AP
detects interference on radio band and switches channels
|
{ap} detects radar
burst on radio {radio} and channel {dfs-channel} goes into
non-occupancy period.
|
Informational
|
No action required.
|
AP detects radar burst
on radio channel and shuts channel for non-occupancy interval.
|
{ap} non-occupancy
period expires on radio {radio} and switches back to channel
{to-channel}.
|
Informational
|
No action required.
|
AP non-occupancy
period expires on radio channel and service is restored
|
{ap} detects
interference on radio {radio} and changes transmit power from
{from-tx} power to {to-tx} power.
|
Informational
|
No action required.
|
AP detects
interference on radio channel and lowers transmit power accordingly
|
{ap} detects less
interference on radio {radio} and changes transmit power from
{from-tx} power to {to-tx} power.
|
Informational
|
No action required.
|
AP detects less
interference on radio channel and raises transmit power accordingly
|
SpeedFlex: {ap} to
{apto} - downlink {downlink}, uplink {uplink}
|
Informational
|
No action required.
|
SpeedFlex: AP to AP
down link and uplink throughput results
|
SpeedFlex: {ap} to
{apto} - downlink {downlink}
|
Informational
|
No action required.
|
SpeedFlex: AP to AP
downlink throughput results
|
SpeedFlex: {ap} to
{apto} - uplink {uplink}
|
Informational
|
No action required.
|
SpeedFlex: AP to AP
uplink throughput results
|
SpeedFlex: {ap} to
Unleashed - downlink {downlink}, uplink {uplink}
|
Informational
|
No action required.
|
SpeedFlex: AP to
Unleashed down link and uplink throughput results
|
SpeedFlex: {ap} to
Unleashed - downlink {downlink}
|
Informational
|
No action required.
|
SpeedFlex: AP to
Unleashed downlink throughput results
|
SpeedFlex: {ap} to
Unleashed - uplink {uplink}
|
Informational
|
No action required.
|
SpeedFlex: AP to
Unleashed uplink throughput results
|
{ap} Cable Modem
interface is down.
|
Critical
|
Reboot the Cable Modem interface. If you encounter
this message frequenty, contact RUCKUS Technical Support.
|
Cable Modem interface
is down
|
{ap} Cable Modem
restarted by administrator.
|
Informational
|
No action required.
|
Cable Modem restarted
by admin.
|
Unleashed {ip} sends
heartbeat to NMS periodically.
|
Warning
|
No action required.
|
Unleashed sent message
to Network Management System (SNMP trap)
|
A new {rogue} with
{ssid} is detected
|
Critical
|
Locate the rogue AP
and disconnect it from the network.
|
Rogue AP detected with
specific SSID
|
{rogue}/{ip} with
{ssid} is detected by {ap} on the local wired network
|
Critical
|
Locate the rogue AP
and disconnect it from the network.
|
Rogue AP(IP) detected
with specific SSID on wired network
|
A new ad-hoc network
{adhoc} with {ssid} is detected
|
Warning
|
Locate the rogue AP
and disconnect it from the network.
|
An ad-hoc,
SSID-spoofing, MAC-spoofing, Same-Network or User-Defined Rogue AP
is identified as a Rogue AP and is rejected.
|
A new user blocked
{rogue} with {ssid} is first detected by {ap}.
|
Warning
|
Locate the rogue AP
and disconnect it from the network.
|
Same as above.
|
A new SSID-spoofing
{rogue} with {ssid} is first detected by {ap}
|
Critical
|
Locate the rogue AP
and disconnect it from the network.
|
Same as above.
|
A new MAC-spoofing
{rogue} with {ssid} is first detected by {ap}
|
Critical
|
Locate the rogue AP
and disconnect it from the network.
|
Same as above.
|
A new Same-Network
{rogue} with {ssid} is first detected by {ap}
|
Warning
|
Locate the rogue AP
and disconnect it from the network.
|
Same as above.
|
A {rogue} with {ssid}
interferes with {ap} on channel {channel}.
|
Warning
|
Locate the rogue AP
and disconnect it from the network.
|
Rogue AP is detected
and rejected by RW AP.
|
Spectrum analysis
failed in {ap}
|
Warning
|
Check whether the AP
supports spectrum analysis.
|
Spectrum analysis
failed.
|
A Malicious {rogue}
detection by {ap} goes away
|
Critical
|
No action required.
|
Unleashed uses a
malicious rogue AP list to store the bssid of malicious AP
|
{ap} detects excessive
probe requests on radio {radio}.
|
Warning
|
Possible DoS attack.
|
Possible attack,
notification to 802.11 trace mgmt
|
{ap} detects excessive
802.11 management frames on radio {radio}.
|
Warning
|
Possible DoS attack.
|
Possible attack,
notification to 802.11 trace mgmt
|
{ap} joins with
different firmware/custom file version and is being upgraded.
|
Warning
|
No action required.
|
AP joins with
different firmware version and is being upgraded.
|
{ap} image has been
upgraded from {old-ver} to {new-ver}
|
Informational
|
No action required.
|
AP image has been
upgraded from <version1> to <version2>
|
{ap} image has been
upgraded from {old-ver} to {new-ver} after {err-cnt} retries.
|
Informational
|
No action required.
|
AP image has been
upgraded from <version1> to <version2> after
<count> retries.
|
Failed to upgrade {ap}
image from {old-ver} to {new-ver}
|
Informational
|
Try again. If you encounter this message
frequently, contact RUCKUS Technical Support.
|
AP version upgrade
failed. Try again.
|
Failed to upgrade {ap}
image from {old-ver} to {new-ver}, possibly due to incorrect IP
address on AP.
|
Informational
|
Check the AP's IP
address settings.
|
AP version upgrade
failed.
|
Failed to upgrade {ap}
image from {old-ver} to {new-ver} after {err-cnt} retries
|
Informational
|
Try again. If you encounter this message
frequently, contact RUCKUS Technical Support.
|
AP version upgrade
failed. Try again.
|
{ap} backup image has
been upgraded from {old-ver} to {new-ver}
|
Informational
|
No action required.
|
AP backup image has
been upgraded from <version1> to <version2>
successfully.
|
{ap} backup image has
been upgraded from {old-ver} to {new-ver} after {err-cnt} retries.
|
Informational
|
No action required.
|
AP backup image
upgraded successfully.
|
{ap} backup image has
been upgraded from {old-ver} to {new-ver} after {err-cnt} retries.
|
Informational
|
No action required.
|
AP backup image
upgraded successfully after x number of retries.
|
Failed to upgrade {ap}
backup image from {old-ver} to {new-ver}
|
Informational
|
Try again. If you encounter this message
frequently, contact RUCKUS Technical Support.
|
AP backup image
upgrade failed. Try again.
|
Failed to upgrade {ap}
backup image from {old-ver} to {new-ver}, possibly due to incorrect
IP address on AP.
|
Informational
|
Check the AP's IP
address settings.
|
AP backup image
upgrade failed.
|
Failed to upgrade {ap}
backup image from {old-ver} to {new-ver} after {err-cnt} retries
|
Informational
|
Try again. If you encounter this message
frequently, contact RUCKUS Technical Support.
|
AP backup image
upgrade failed. Try again.
|
{ap} custom file has
been upgraded to {new-custom}.
|
Informational
|
No action required.
|
AP custom file has
been upgraded successfully.
|
Fail to upgrade {ap}
custom file to {new-custom}.
|
Informational
|
Try again. If you encounter this message
frequently, contact RUCKUS Technical Support.
|
Custom file upgrade failed. Try again.
|
RUCKUS PKI certificate of {ap} upgraded.
|
Informational
|
No action required.
|
AP's RUCKUS PKI certificate installed or upgraded.
|
Failed to upgrade RUCKUS PKI certificate of {ap}.
|
Informational
|
Try again. If you encounter this message
frequently, contact RUCKUS Technical Support.
|
AP's RUCKUS PKI certificate upgrade failed.
|
Receiving System Info
from {ap}
|
Informational
|
No action required.
|
Unleashed received
system info from AP
|
Receiving Cable Modem
Info from {ap}
|
Informational
|
No action required.
|
Unleashed received
cable modem info from AP
|
Failed to initialize
the configuration of all APs because AP limit exceeded.
|
Critical
|
Delete APs from the
list to allow new APs to join.
|
Too many AP's tried to
join to Unleashed. Exceeded AP limit.
|
Receiving RF Info from
{ap}
|
Informational
|
No action required.
|
Unleashed received RF
info from AP
|
Imported {ap-cnt} APs
from backup configuration, {new-apg-cnt} of them AP-group mismatch,
{new-wlg-cnt} of them wlan-group mismatch
|
Informational
|
No action required.
|
Imported configuration
(from backup) has too many AP's.
|
{apgrp} modified by
admin from {ip}
|
Informational
|
No action required.
|
AP group is modified
by an admin
|
{apgrp} created by
admin from {ip}
|
Informational
|
No action required.
|
AP group is created by
an admin
|
{apgrp} deleted by
admin from {ip}
|
Informational
|
No action required.
|
AP group is deleted by
an admin
|
{apgrp} of the
imported backup configuration is undefined.
|
Informational
|
Create the relevant AP
Group and import again.
|
AP group imported from
backup configuration undefined.
|
{wlan} modified by
admin from {ip}
|
Informational
|
No action required.
|
Wlan is modified by an
admin.
|
{wlan} created by
admin from {ip}
|
Informational
|
No action required.
|
Wlan is created by an
admin.
|
{wlan} deleted by
admin from {ip}
|
Informational
|
No action required.
|
Wlan is deleted by an
admin.
|
{wlan} enabled by
administrator.
|
Informational
|
No action required.
|
WLAN is enabled by
admin.
|
{wlan} disabled by
administrator.
|
Informational
|
No action required.
|
WLAN is disabled by
admin.
|
{wlan} enabled
according to service schedule.
|
Informational
|
No action required.
|
WLAN is enabled by
service schedule.
|
{wlan} disabled
according to service schedule.
|
Informational
|
No action required.
|
WLAN is disabled by
service schedule.
|
The role {role} is
modified by admin, so disconnect the station in this role.
|
Informational
|
No action required.
|
Role is modified by
admin, all currently connected stations with this role disconnected.
|
{role} enabled by
administrator.
|
Informational
|
No action required.
|
Role is enabled by
admin.
|
{role} disabled by
administrator.
|
Informational
|
No action required.
|
Role is disabled by
admin.
|
{role} enabled
according to time range.
|
Informational
|
No action required.
|
Role is enabled by
time range.
|
{role} disabled
according to time range.
|
Informational
|
No action required.
|
Role is disabled by
time range.
|
{wlangrp} modified by
admin from {ip}
|
Informational
|
No action required.
|
Wlan group is modified
by an admin.
|
{wlangrp} created by
admin from {ip}
|
Informational
|
No action required.
|
Wlan group is created
by an admin.
|
{wlangrp} deleted by
admin from {ip}
|
Informational
|
No action required.
|
Wlan group is deleted
by an admin.
|
{wlangrp} of the
imported backup configuration is undefined.
|
Informational
|
Create the relevant
WLAN Group and import again.
|
Wlan group imported
from a backup configuration is undefined.
|
Warning about online
client numbers from {ap} exceed threshold {value} is cleared.
|
Informational
|
No action required.
|
AP Warning about the
online client number exceeding threshold is cleared
|
{ap} is online.
|
Informational
|
No action required.
|
AP is online
|
{ap} wireless
interface experienced high reception error.
|
Informational
|
Reboot the AP. If you encounter this message
frequently, contact RUCKUS Technical Support.
|
AP wireless interface
experienced high reception errors.
|
System CPU utilization
{util} exceeds threshold {value}, {count} times.
|
Warning
|
Disable debug mode or
stop Real Time Monitoring to free resources.
|
System CPU utilization
exceeded threshold<count> times.
|
System memory
utilization {util} exceeds threshold {value}, {count} times.
|
Warning
|
Disable debug mode or
stop Real Time Monitoring to free resources.
|
System memory
utilization exceeded threshold <count> times.
|
System CPU utilization
{util} is less than threshold {value}, and clears warning {count}
times.
|
Warning
|
No action required.
|
System CPU utilization
less than threshold warning cleared <count> times.
|
System memory
utilization {util} is less than threshold {value}, and clears
warning {count} times.
|
Warning
|
No action required.
|
System memory
utilization less than threshold warning cleared <count> times.
|
System bandwidth
utilization {util} exceeds threshold {value}.
|
Warning
|
Reduce bandwidth
utilization.
|
System bandwidth
utilization exceeded threshold <value>.
|
System packet-drop
rate {util} exceeds threshold {value}.
|
Warning
|
Check client
connectivity.
|
System packet drop
rate exceeded threshold.
|
{ap} fails to
synchronize clock with Unleashed
|
Warning
|
If you encounter this message frequently, contact
RUCKUS Technical Support.
|
AP clock
synchronization with Unleashed failed.
|
Radio {radio} of {ap}
has switched wlan group from {old-group} to {new-group}
|
Informational
|
No action required.
|
AP radio has switched
wlan group from <group1> to <group2>.
|
| [Smart Redundancy] Peer {Unleashed}{peer-ip}
has upgraded AP patch. |
Informational |
No action required. |
A new AP model patch has been applied to
the peer Unleashed. |
| [Smart Redundancy] AP patch upgrading
command received from peer {Unleashed}{peer-ip} |
Informational |
No action required. |
The peer Unleashed has sent a request for a
new AP model patch. |
[Smart Redundancy]
Peer Unleashed{peer-ip} has been restored.
|
Critical
|
No action required.
|
[Smart Redundancy]
Peer Unleashed configuration has been restored.
|
[Smart Redundancy]
System is being upgraded per command from peer Unleashed{peer-ip}
|
Critical
|
No action required.
|
[Smart Redundancy]
System received upgrade command from peer Unleashed.
|
[Smart Redundancy]
System restored command received from peer Unleashed{peer-ip}
|
Critical
|
No action required.
|
[Smart Redundancy]
System received configuration restore command from peer Unleashed.
|
[Smart Redundancy]
Could not retrieve necessary file from peer Unleashed{peer-ip}.
Operation aborted.
|
Critical
|
Try again. If you encounter this message
frequently, contact RUCKUS Technical Support.
|
[Smart Redundancy]
System could not retrieve necessary file from peer Unleashed.
Operation aborted.
|
[Smart Redundancy]
Peer Unleashed{peer-ip} image has been upgraded from {old-version}
to {new-version}. System is being upgraded.
|
Warning
|
No action required.
|
[Smart Redundancy]
Peer Unleashed image has been upgraded successfully. System is being
upgraded
|
[Smart Redundancy]
System upgraded, peer Unleashed upgrade pending.
|
Critical
|
No action required.
|
[Smart Redundancy]
System has been upgraded and peer Unleashed upgrade is pending.
|
[Smart Redundancy]
System upgraded, peer Unleashed upgrade pending.
|
Critical
|
No action required.
|
|
[Smart Redundancy]
Peer Unleashed{peer-ip} upgrade failed.
|
Critical
|
Try again. If you encounter this message
frequently, contact RUCKUS Technical Support.
|
[Smart Redundancy]
Peer Unleashed upgrade failed.
|
[Smart Redundancy]
Sync configuration to peer Unleashed{peer-ip}
|
Critical
|
No action required.
|
[Smart Redundancy]
System sync configuration to peer Unleashed.
|
[Smart Redundancy]
System ready to sync configuration from peer Unleashed{peer-ip}
|
Critical
|
No action required.
|
[Smart Redundancy]
System is about to sync configuration from peer Unleashed.
|
[Smart Redundancy]
Sync configuration from peer Unleashed{peer-ip}
|
Informational
|
No action required.
|
[Smart Redundancy]
System finished configuration sync from peer Unleashed.
|
[Smart Redundancy]
Standby Unleashed has more recent configuration than the active
Unleashed
|
Critical
|
Do not make
configuration changes on the standby Unleashed.
|
[Smart Redundancy]
Standby Unleashed has more recent configuration than the active
Unleashed.
|
[Smart Redundancy]
Failed to sync configuration from peer Unleashed{peer-ip} due to
{lmsg}
|
Informational
|
Try again. If you encounter this message
frequently, contact RUCKUS Technical Support.
|
[Smart Redundancy]
System failed to sync configuration from peer Unleashed with reason.
|
[Smart Redundancy]
Admin forces a failover to peer Unleashed{peer-ip}
|
Critical
|
No action required.
|
[Smart Redundancy]
Admin forced a failover to peer Unleashed.
|
[Smart Redundancy]
Received failover command to change state to {to-state} from peer
Unleashed{peer-ip}
|
Critical
|
No action required.
|
[Smart Redundancy]
System received failover command from peer Unleashed to change
state.
|
[Smart Redundancy]
<strong>Failed!</strong> Firmware version mismatch
|
Critical
|
Ensure that both peers
in a Smart Redundancy configuration have the same firmware version.
|
[Smart Redundancy]
System detected mismatch of peer Unleashed firmware version.
|
| [Smart Redundancy]
<strong>Failed!</strong> AP Firmware version mismatch |
Warning |
Ensure that any new AP model patch files
that have been imported into one Unleashed have also been applied to the
peer. |
[Smart Redundancy] System detected a
mismatch of peer Unleashed’s AP firmware version. |
| [Smart Redundancy] New SR has lower
licensed APs |
Warning |
Ensure that you have enough AP licenses for
your APs on both SR peers. |
[Smart Redundancy] The New SR peer device
has a lower number of AP licenses. |
[Smart Redundancy] New
SR has lower licensed APs
|
Warning
|
|
[Smart Redundancy] The
New SR peer device has a lower number of AP licenses.
|
[Smart Redundancy]
Model mismatch (i.e. Unleashed1000 cannot pair with Unleashed3000)
|
Critical
|
Ensure that both peers
in a Smart Redundancy configuration are the same model.
|
[Smart Redundancy]
System detected mismatch of peer Unleashed model (i.e. Unleashed1000
cannot pair with Unleashed3000).
|
[Smart Redundancy]
Connection from peer {Unleashed} IP address is different from that
configured
|
Critical
|
Check the IP address
of the peer Unleashed.
|
[Smart Redundancy]
System detected IP address from peer Unleashed connection is
different from that configured.
|
[Smart Redundancy]
Received unrecognized command from peer Unleashed{peer-ip}, it may
be caused by Shared Secret mismatch
|
Critical
|
Ensure that the Shared
Secret is the same on both Smart Redundancy peers.
|
[Smart Redundancy]
System received unrecognized command from peer Unleashed that could
be caused by shared scret mismatch.
|
[Smart Redundancy]
System state changed to {state} due to {reason}
|
Critical
|
No action required.
|
[Smart Redundancy]
System state changed with reason.
|
[Smart Redundancy]
Peer Unleashed{peer-ip} not found, system changed to active state.
|
Critical
|
Check connectivity
between Smart Redundancy peers.
|
[Smart Redundancy]
Peer Unleashed connection lost, system changed to active state.
|
[Smart Redundancy]
Peer Unleashed{peer-ip} connected, system is in active state.
|
Critical
|
No action required.
|
[Smart Redundancy]
Peer Unleashed connected, system is in active state.
|
[Smart Redundancy]
Peer Unleashed{peer-ip} connected, system is in standby state.
|
Critical
|
No action required.
|
[Smart Redundancy]
Peer Unleashed connected, system is in standby state.
|
[Smart Redundancy]
Lost connection to peer Unleashed{peer-ip}, system is in active
state.
|
Critical
|
Check connectivity
between Smart Redundancy peers.
|
[Smart Redundancy]
Lost connection to peer Unleashed, system is in active state.
|
[Smart Redundancy]
Lost connection to peer Unleashed{peer-ip}, system is in standby
state.
|
Critical
|
Check connectivity
between Smart Redundancy peers.
|
[Smart Redundancy]
Lost connection to peer Unleashed, system is in standby state.
|
[Smart Redundancy]
System is currently being upgraded; disconnected from peer
Unleashed.
|
Critical
|
No action required.
|
[Smart Redundancy]
System is currently being upgraded; disconnect from peer Unleashed.
|
[Smart Redundancy]
Peer Unleashed is being upgraded.
|
Critical
|
No action required.
|
[Smart Redundancy]
Peer Unleashed is being upgraded.
|
[Smart Redundancy]
Peer Unleashed did not reconnect after upgrade or restore
configuration. Local Upgrade is aborted, please check the peer
Unleashed.
|
Warning
|
No action required.
|
[Smart Redundancy]
Peer Unleashed did not reconnect after upgrade. System is being
upgraded automatically.
|
[Smart Redundancy]
System received command {cmd} from peer Unleashed but the command
has been completed already due to connection timeout.
|
Critical
|
No action required.
|
[Smart Redundancy]
System completed upgrade due to timeout in connection to peer
Unleashed without waiting for upgrade command sent from peer
Unleashed.
|
[Smart Redundancy]
Peer Unleashed{peer-ip} is being upgraded by administrator to sync
up firmware version.
|
Critical
|
No action required.
|
[Smart Redundancy]
Peer Unleashed is being upgraded by administrator to sync up
firmware version.
|
[Smart Redundancy]
System is being upgraded by administrator to sync up firmware
version.
|
Critical
|
No action required.
|
[Smart Redundancy]
System is being upgraded by administrator to sync up firmware
version.
|
[Smart Redundancy]
Peer Unleashed{peer-ip} is lost after upgrade. Please check the
status of Peer Unleashed.
|
Critical
|
Check the status of
the peer Unleashed.
|
[Smart Redundancy]
Peer Unleashed IP address lost after upgrade. Please check the
status of the peer Unleashed.
|
Administrator decide
to use {higher} Smart Redundancy license.
|
Informational
|
No action required.
|
[Smart Redundancy] The
admin has selected a higher number of combined AP licenses.
|
{ap} is reset for
Smart Redundancy.
|
Critical
|
No action required.
|
AP reboot due to Smart
Redundancy.
|
Upgrade or Restore is
pending... Please wait about 10-15 minutes to try again.
|
Critical
|
Try again after 10-15
minutes.
|
Upgrade or restore
pending.
|
{wlan} has been
deployed on radio {radio} of {ap} with {vap}
|
Informational
|
No action required.
|
Wlan has been deployed on Radio of AP with VAP
|
{wlan} with {vap} has
been removed from radio {radio} of {ap}
|
Informational
|
No action required.
|
Wlan with VAP has been
removed from Radio of AP.
|
{wlan} with {vap}
configuration has been updated on radio {radio} of {ap}
|
Informational
|
No action required.
|
Wlan with VAP
configuration has been updated on Radio of AP.
|
{wlan} with {vap} has
been deployed on radio {radio} of {ap} after retry.
|
Informational
|
No action required.
|
Wlan with VAP has been
deployed on Radio of AP after retry.
|
{wlan} with {vap}
configuration has been updated on radio {radio} of {ap} after retry
|
Informational
|
No action required.
|
Wlan with VAP
configuration has been updated on Radio of AP after retry.
|
{wlan} with {vap} has
been removed from radio {radio} of {ap} after retry
|
Informational
|
No action required.
|
Wlan with VAP has been
removed from Radio of AP after retry.
|
Failed to deploy
{wlan} on radio {radio} of {ap}
|
Informational
|
Reboot the AP. If you encounter this message
frequently, contact RUCKUS Technical Support.
|
Failure to deploy Wlan
on Radio of Ap.
|
Failed to remove
{wlan} from radio {radio} of {ap}
|
Informational
|
Reboot the AP. If you encounter this message
frequently, contact RUCKUS Technical Support.
|
Failure to remove Wlan
from Radio of AP.
|
Failed to update
{wlan} configuration of radio {radio} of {ap}
|
Informational
|
Reboot the AP. If you encounter this message
frequently, contact RUCKUS Technical Support.
|
Failure to update Wlan
configuration of Radio of AP.
|
Failed to deploy
{wlan} on radio {radio} of {ap}, try again.
|
Informational
|
Reboot the AP. If you encounter this message
frequently, contact RUCKUS Technical Support.
|
Failure to deploy Wlan
on Radio of AP.
|
Failed to update
{wlan} configuration of radio {radio} of {ap},try again.
|
Informational
|
Reboot the AP. If you encounter this message
frequently, contact RUCKUS Technical Support.
|
Failure to update Wlan
configuration of Radio of AP.
|
Failed to remove
{wlan} configuration of radio {radio} of {ap},try again.
|
Informational
|
Reboot the AP. If you encounter this message
frequently, contact RUCKUS Technical Support.
|
Failure to remove Wlan
configuration of Radio of AP.
|
| {wlan} cannot be deployed to radio {radio}
of {ap} because this WLAN is only bound to radio {bound_radio}. |
Informational
|
No action required. |
WLAN cannot be deployed to the AP's radio
because the bound radio is unavailable on this AP. |
| {wlan} cannot be deployed to radio {radio}
of {ap} because its suiteb192 WLAN and AP mode {model} does not support
it. |
Informational
|
No action required. |
WLAN cannot be deployed to the AP because
this AP model does not support Suite B 192-bit profile for TLS. |
Wired {user} joins
{port} from {ap}
|
Informational
|
No action required.
|
Wired client joins
port at AP.
|
Wired {user}
disconnected by admin from {port} at {ap}
|
Informational
|
No action required.
|
Wired client
disconnected by admin from port at AP.
|
Wired {user} leave
from {port} at {ap}
|
Informational
|
No action required.
|
Wired client leaves
from port at AP.
|
Wired {user} IEEE
802.1X authentication failed from {port} at {ap}
|
Informational
|
Check authentication
settings on AP port and wired client.
|
IEEE 802.1X
authentication failed on wired client from port at AP.
|
{user} joins {wlan}
from {ap}
|
Informational
|
No action required.
|
Client joined WLAN
from AP.
|
{user} with {vlan}
joins {wlan} from {ap}
|
Informational
|
No action required.
|
Client with VLAN
joined WLAN from AP.
|
{user} rejoins {wlan}
from {ap}
|
Informational
|
No action required.
|
Client rejoins WLAN
from AP.
|
{user} with {vlan}
rejoins {wlan} from {ap}
|
Informational
|
No action required.
|
Client with VLAN
rejoins WLAN from AP.
|
{user} fails to join
{wlan} from {ap}
|
Informational
|
Check user
authentication credentials.
|
Client failed to join
WLAN from AP.
|
{user} is refused
access to {wlan} from {ap} because there are too many users on that
AP, WLAN, or Radio.
|
Informational
|
Increase APs to
provide additional capacity.
|
Client refused to join
WLAN from ap because there are too many users on that AP, WLAN, or
Radio.
|
{user} fails to join
{wlan} from {ap} due to authentication failure
|
Informational
|
Check user
authentication credentials.
|
Client failed to join
WLAN from AP due to authentication failure.
|
{user} idle timeout
and disconnected from {wlan} at {ap}
|
Informational
|
No action required.
|
Client idle timeout
and disconnected from WLAN at AP.
|
{user} disconnects
from {wlan} at {ap}
|
Informational
|
No action required.
|
Client disconnected
from WLAN at AP.
|
{ap} radio {radiofrom}
detects {user} in {wlan} roams out to {apto}
|
Informational
|
No action required.
|
AP (from) radio
detected client in WLAN roams out to AP(to).
|
{ap} radio {radioto}
detects {user} in {wlan} roams from {apfrom}
|
Informational
|
No action required.
|
AP(to) radio detected
client in WLAN roams from AP(from).
|
{user} disconnected by
admin from {wlan} at {ap}
|
Informational
|
No action required.
|
Client disconnected by
admin from WLAN at AP.
|
{user} logged out by
user from {wlan} at {ap}
|
Informational
|
No action required.
|
User logged out from
WLAN at AP.
|
{user} disconnected by
timebased rule from {wlan} at {ap}
|
Informational
|
No action required.
|
Client disconnected by
timebased rule from WLAN at AP.
|
{user} disassociated
from {wlan} due to timeout waiting for AP to add station.
|
Informational
|
No action required.
|
Client disassociated
from WLAN due to timeout waiting for AP to add station.
|
{user} joins {wlan}
from {ap} with {rssi} and client's rssi is below threshold
{rssi-threshold}
|
Informational
|
No action required.
|
Client joined WLAN
from AP with rssi and client's rssi is below rssi-threshold.
|
{user} leave {wlan} at
{ap} with {session_time} {rx_bytes} {tx_bytes}
|
Informational
|
No action required.
|
Client leaves WLAN at
AP with session_time, rx_bytes, and tx_bytes.
|
| The Authorization of {user} is changed by
Radius CoA |
Informational |
No action required. |
User authorization status changed due to
CoA (change of authorization) message from RADIUS. |
{user} disassociated
from {wlan} at {ap} due to timeout during authentication.
|
Informational
|
Check user
authentication credentials.
|
Client disassociated
from WLAN at AP due to timeout during authentication.
|
User{sta-mac}
disassociated from {wlan} at {ap} due to force DHCP timeout. User IP
{sta-ip}, {vlan}, DHCPassigned-IP {sta-dhcp-ip}, DHCP lease time
{sta-dhcplease}.
|
Informational
|
No action required.
|
User disassociated due
to force DHCP timeout.
|
{user} tries to
connect to an unauthorized {wlan}
|
Warning
|
No action required.
|
Client tried to
connect to an unauthorized WLAN.
|
{user} session time
limit exceeded; session terminated
|
Informational
|
No action required.
|
client session time
limit exceeded; session terminated.
|
{user} of {wlan} is
authorized at {ap}
|
Informational
|
No action required.
|
Client of WLAN is
authorized at AP.
|
{user} repeatedly
fails authentication when joining {wlan} at {ap}.
|
Warning
|
Check user
authentication credentials.
|
Client repeatedly
failed authentication when joining WLAN at AP.
|
{user} fails
authentication too many times in a row when joining {wlan} at {ap}.
{user} is temporarily blocked from the system for {block}.
|
Critical
|
Check user
authentication credentials.
|
Client failed
authentication too many times in a row when joining WLAN at AP.
Client is temporarily blocked from system for some time.
|
{user} fails to login
{wlan} at {ap} too many times and is temporarily blocked from login
for {block}.
|
Warning
|
Check user
authentication credentials.
|
Client failed to login
WLAN at AP too many times and is temporarily blocked from login for
some time.
|
{mac} attempts to
login to {wlan} at {ap} too many times and is temporarily blocked
from login for {block}.
|
Warning
|
Check user
authentication credentials.
|
Device with mac
address attempted to login to WLAN at AP too many times and is
temporarily blocked from login.
|
Temporary blocking of
User{user-name} unblocked.
|
Warning
|
No action required.
|
Temporary blocking of
username (client) unblocked.
|
Temporary blocking of
{mac} unblocked.
|
Warning
|
No action required.
|
Temporary blocking of
device with mac address unblocked.
|
User{user-name} has
acquired a new Dynamic PSK.
|
Informational
|
No action required.
|
Client has acquired a
new Dynamic PSK.
|
Administrator has
acquired batch generation of {num} new Dynamic PSKs.
|
Informational
|
No action required.
|
Administrator has
acquired batch generation of # new Dynamic PSKs.
|
{user}'s access is
restricted because of an expired Dynamic PSK.
|
Informational
|
Create a new Dynamic
PSK for this user. If you encounter this message frequently,
increase Dynamic PSK expiration value.
|
Client access is
restricted because of an expired Dynamic PSK.
|
{user} has renewed a
Dynamic PSK.
|
Informational
|
No action required.
|
Client has renewed a
Dynamic PSK.
|
{user} reconnects to
{ap} within grace period. No additional authentication is required.
|
Informational
|
No action required.
|
Client reconnected to
AP within grace period. No additional authentication is required.
|
DPSKs of
WLAN{wlan-name} are deleted.
|
Informational
|
No action required.
|
DPSKs deleted for a
WLAN.
|
| {user} of {wlan} can not be allowed
temporarily due to internal error |
Informational |
No action required. |
Client is temporarily blocked due to an
internal error. |
UMM {url} sends a bad
{file} file.
|
Critical
|
Try again. If you encounter this message
frequently, contact RUCKUS Technical Support.
|
System received a bad
file from UMM.
|
UMM {url} issues image
upgrade command.
|
Informational
|
No action required.
|
System received image
upgrade command from UMM.
|
UMM {url} issues
restart command.
|
Informational
|
No action required.
|
System received
restart command from UMM.
|
UMM {url} issues
restore command {action}.
|
Informational
|
No action required.
|
System received
restore command from UMM.
|
Unleashed contacts UMM
{status}.
|
Informational
|
No action required.
|
System contacted UMM
failed/successfully.
|
UMM {url} issues
command to write configuration template.
|
Informational
|
No action required.
|
System received
command(write configuration template) from UMM.
|
Unleashed successfully
writes configuration template successfully cmdkey {cmdkey}.
|
Critical
|
No action required.
|
System wrote
configuration template successfully with cmdkey from UMM.
|
Write template fail
due to {err} cmdkey {cmdkey}.
|
Critical
|
Try again. If you encounter this message
frequently, contact RUCKUS Technical Support.
|
System failed to write
configuration template. Error indicated for cmdkey which failed.
|
Unleashed fails to
retrieve template file from UMM{url} cmdkey {cmdkey}.
|
Informational
|
Try again. If you encounter this message
frequently, contact RUCKUS Technical Support.
|
System failed to
retrieve template file from UMM with cmdkey.
|
Unleashed file
download from UMM{url} timeout cmdkey {cmdkey}.
|
Informational
|
Check connectivity
between Unleashed and UMM.
|
System timeout
downloading file from UMM with cmdkey.
|
UMM {url} changes the
UMM monitoring event list.
|
Informational
|
No action required.
|
UMM changed the
monitoring event list.
|
Unleashed is not
Active and skips UMM {url} command cmdkey {cmdkey}.
|
Informational
|
No action required.
|
System is not in
active state and skips UMM command.
|
| SMTP server {name} unavailable. |
Warning |
Check connectivity between Unleashed and
SMTP server. |
System is unable to connect to SMTP server.
|
RADIUS authentication
server {ip} unavailable.
|
Warning
|
Check connectivity
between Unleashed and RADIUS server.
|
RADIUS authentication
server unavailable.
|
RADIUS accounting
server {ip} unavailable.
|
Warning
|
Check connectivity
between Unleashed and RADIUS server.
|
RADIUS accounting
server unavailable.
|
SSID{id} RADIUS
authentication server {change} to {server}.
|
Warning
|
No action required.
|
Reconnect/Failover to
Radius authentication server
|
SSID{id} RADIUS
accounting server {change} to {server}.
|
Warning
|
No action required.
|
Reconnect/Failover to
Radius accounting server.
|
RADIUS authentication
server {change} to {server}.
|
Warning
|
No action required.
|
Reconnect/Failover to
Radius authentication server.
|
Bonjour Gateway
automatically reboot for the following reason:{reason}.
|
Warning
|
No action required.
|
Bonjour Gateway
service rebooted.
|
Bonjour Gateway is
started.
|
Informational
|
No action required.
|
Bonjour Gateway
service started.
|
Bonjour Gateway is
stopped.
|
Informational
|
No action required.
|
Bonjour Gateway
service stopped.
|
Bonjour Gateway
restart.
|
Informational
|
No action required.
|
Bonjour Gateway
service restarted.
|
Sensor {desc} status
is {status}
|
Critical
|
No action required.
|
Sensor description and
it's status
|
Turn On the the {ap}'s
ChannelFly according to {apgrp} setting.
|
Informational
|
No action required.
|
ChannelFly enabled for
this AP based on AP Group settings.
|
Turn Off the the
{ap}'s ChannelFly according to {apgrp} setting.
|
Informational
|
No action required.
|
ChannelFly disabled
for this AP based on AP Group settings.
|
Spectrum analysis of
{ap} is enabled
|
Informational
|
No action required.
|
AP Spectrum Analysis
feature enabled.
|
Spectrum analysis of
{ap} is disabled
|
Informational
|
No action required.
|
AP Spectrum Analysis
feature disabled.
|
Support Entitlement
file has been downloaded from the {cn} Entitlement Server.
|
Warning
|
No action required.
|
Support Entitlement file has been downloaded from
the RUCKUS Entitlement Server.
|
Failed to download the
Support Entitlement file from the {cn} Entitlement Server.
|
Critical
|
Try again. If the
problem persists, check your connection to the entitlement server,
and check the status of your entitlements.
|
Failed to download the Support Entitlement file
from the RUCKUS Entitlement Server.
|
| Synchronized the URL Filtering License file
from the {cn} Server |
Informational
|
No action required. |
URL filtering license file synchronized.
|
| Failed to download the URL Filtering
License file from the {cn} Server |
Warning |
Try again. If the
problem persists, check your connection to the URL filtering license
server, and check the status of your URL filtering license.
|
Failed to download the URL filtering license file from the RUCKUS
license server. |
| URL Filtering is disabled due to
insufficient license |
Warning |
Update URL filtering license file. |
URL filtering disabled due to insufficient
license. |
| The URL Filtering licenses entitled to {1}
APs on this Wireless Controller appear to expire in {2} days. Please
contact Support for further assistance. |
Warning |
No action required. |
URL filtering license about to expire.
|
| The URL Filtering licenses on this Wireless
Controller appear to have expired,valid licenses are:{1}-less than
connected APs,this feature is disabled. Please contact Support for
further assistance. |
Warning |
No action required. |
URL filtering license expired. |
| The URL filtering will be enabled for 90
days using temporary license. Within these 90 days, a valid URL
filtering license must be loaded. Otherwise, URL filtering will be
disabled until a valid license is loaded. |
Warning |
No action required. |
Temporary URL filtering license valid for
90 days. |
| Radio {radioindex} of {ap} is ON |
Warning |
No action required. |
AP radio has been turned on. |
| {radioindex} of {ap} is OFF |
Warning |
No action required. |
AP radio has been turned off. |
| User{pppoe-user} connected with PPPOE
server successfully |
Informational |
No action required. |
PPPoE user successfully connected to PPPoE
server. |
| User{pppoe-user} disconnected from PPPOE
server |
Informational |
No action required. |
PPPoE user disconnected from PPPoE server.
|
| PPPeE Client authentication failure |
Warning |
Check client login credentials. |
PPPoE client authentication failure.
|
| Start client connectivity troubleshooting
for station {mac} |
Warning |
No action required. |
Client connectivity troubleshooting
started. |
| Stop client connectivity troubleshooting
for station {mac} |
Warning |
No action required. |
Client connectivity troubleshooting
stopped. |
| External gateway status change from
{old-status} to {new-status} |
Warning |
No action required. |
External gateway status change detected.
|
| Hello {system-id}! |
Informational |
No action required. |
Hello system message. |
| Social Login for WiFi Access |
Informational |
No action required. |
Social Media login. |
| Welcome to the WeChat login page |
Informational |
No action required. |
WeChat login. |
| Remove preload image fail! {reason} |
Warning |
Examine the reason for the failure. |
Unleashed failed to remove preloaded image
due to {reason}. |
| start ad server for 802.1X {search-base}
{server1} {host-device-name} {admin-dn}. |
Informational |
No action required. |
Active Directory for 802.1X server started.
|
| stop ad server for 802.1X. |
Informational |
No action required. |
Active Directory for 802.1X server stopped.
|
| Unknown Error |
Warning |
No action required. |
An unknown error has occurred. |
| AAA server address format error |
Warning |
No action required. |
Error in format of AAA server address. |
| The original UMM configuration is empty |
Warning |
No action required. |
Original UMM configuration is empty. |
| Restore the original configuration failed |
Warning |
No action required. |
Unleashed failed to restore the original
configuration. |
| Backup original configuration failed |
Warning |
No action required. |
Unleashed failed to backup the original
configuration. |
| Domain{hostname} resolve error |
Critical |
Check the domain name. |
Failed to resolve domain name. |
| Domain{hostname} resolve success,IP{IP} |
Critical |
Check the IP address. |
Domain name resolved to a specific IP address
successfully. |
| Domain{hostname} resolve success,IP1{IP}
IP2{IP2} |
Critical |
Check the IP addresses. |
Domain name resolved to IP addresses
successfully. |
| User name can only contain between 1 and 64 characters
and cannot include space or ` or $ or ) or ( or & or | or ; or # or
! or > or < or " or ' or \ |
Warning |
No action required. |
Guidelines for setting user name for guest pass self service. |
| Username error |
Warning |
No action required. |
Username error. |
| Full name must be between 0 and 32 characters |
Warning |
No action required. |
Guidelines for setting user full name. |
| Password can only contain between 4 and 32
characters |
Warning |
No action required. |
Password guidelines. |
| Username:{1} Password cannot contain < > and
" |
Warning |
No action required. |
Password guidelines. |
| Password can not contain < > ,and " |
Warning |
No action required. |
Password guidelines. |
| Username:{1} Full name can not contain < > ,and
" |
Warning |
No action required. |
Guidelines for setting user full name. |
| Full name cannot contain < > ,and " |
Warning |
No action required. |
Guidelines for setting user full name. |
| The Role name cannot contain < > ,and " |
Warning |
No action required. |
Guidelines for setting role name. |
| User name can only contain between 1 and 64 characters
and cannot include space or ` or $ or ) or ( or & or | or ; or # or
! or > or < or " or ' or \ |
Warning |
No action required. |
Guidelines for setting user name. |
| The Role name must be between 1 and 32
characters |
Warning |
No action required. |
Guidelines for setting role name. |
| The Role name cannot contain < > ,and " |
Warning |
No action required. |
Guidelines for setting role name. |
| Role cannot be null |
Warning |
No action required. |
Role name is empty. |
| Built-in AV template {id} cannot be modified |
Warning |
No action required. |
When a user tries to modify a built-in AV
template. |
| AV template cannot be deleted since it is referred by AV
profile {profile} |
Warning |
No action required. |
When a user tries to delete an AV template associated
with an AV profile. |
| AV template name {tmplt_name} already exists |
Warning |
Enter a different template name. |
When a user enters an existing AV template name. |
| AV profile name {profile_name} already exists |
Warning |
Enter a different AV profile name. |
When a user enters an existing AV profile name. |
| The VLAN ID {vlan_id} in this profile is occupied in
another profile {name} |
Warning |
Use another VLAN ID. |
When a user enters a VLAN ID that is already associated
with another AV switch profile. |
| The subnet {subnet} already exists in profile
{name} |
Warning |
Enter a different subnet IP address. |
When a user enters a subnet IP address that is already
associated with another AV switch profile. |
| MSG_Lease_file_download_ok=Synchronized the {zd} Subscription License
file from the {cn} Server |
Informational |
No action required. |
Subscription License file from the server is
synchronized. |
| Failed to get license file from {cn} Subscription
Manager. |
Error |
Import the license file manually or contact RUCKUS
Support for further assistance. |
Failed to get license file from the Subscription
Manager. |
| MSG_lease_file_download_fail=Failed to download the {zd}
Subscription License file from the {cn} Server after tried several
times, all stations' internet access on this AP is limited. |
Informational |
Contact RUCKUS Support for further assistance. |
Failed to download the Subscription License file from
the server after multiple attempts and internet access on all the
stations of the AP is limited. |
| MSG_Spark_AP_lease_status_en={ap}'s Subscription License
status has been changed to {lease-status_en}, all stations' internet
access on this AP is resumed. |
Informational |
No action required. |
Internet access on all the stations of the AP is resumed
when AP Subscription license lease status is enabled. |
| AP's Subscription License status has been changed to
{lease-status_dis}, all stations' internet access on this AP is
limited. |
Informational |
No action required. |
Internet access on all the stations of the AP is limited
when AP Subscription license lease status is disabled. |
| Subscription License file has been imported
manually. |
Informational |
No action required. |
Subscription License file has been imported
manually. |
| MSG_Spark_Lease_Expiring=The credit card binded to AP
with serial number {serial-num} will expire within {days} days. |
Informational |
No action required. |
Expiration information on the credit card binded to AP
with this serial number. |
| MSG_Spark_Lease_Expired=The credit card binded to AP
with serial number {serial-num} has expired |
Informational |
Update with a valid credit card. |
The credit card binded to AP with this serial number has
expired. |
| MSG_SURVIVABILITY_reach_max=The user {survivaname} could
not be added because the wlan survivability entries have reached the
maximum {survivanum}. |
Warning |
No action required. |
The user could not be added because the WLAN
survivability entries have reached the maximum. |
| Username:{username} authentication failed 3 times. Login
or authentication will be blocked for 3 minutes. |
Warning |
No action required. |
If authentication fails for consecutive three login
attempts, the authentication is blocked for three minutes. |
| Username:{username} Authentication failure. |
Warning |
No action required. |
Authentication fails if incorrect user name is
entered. |
| Username:{username} disable login or authentication for
3 minutes. |
Warning |
No action required. |
If authentication fails for consecutive three login
attempts, the login is disabled or the authentication is blocked for
three minutes. |
| Change password success for username:{username}. |
Informational |
No action required. |
Password is changed successfully. |
| The username:{username} does not exist. |
Informational |
Enter the correct user name. |
The username does not exist. |
| Username:{username} New password is the same with old
password. |
Warning |
Enter a new password. |
New password is the same as the old password. |
| GuestCreateMsg=Created-by:{created-by}
Full-Name:{full-name} Role-id:{role-id} SSID:{wlan} Email:{email}
Phone-Number:{phone-number} Remark:{remarks} |
Informational |
No action required. |
Guest message is created. |
| GuestCreatesponsorMsg=Created-by:{created-by}
Approved-sponsor:{approved-sponsor} Role-id:{role-id} SSID:{wlan}
Email:{email} Phone-Number:{phone-number} |
Informational |
No action required. |
Guest sponsor message is created. |
| UN_E_ICX_CLI_SET_FINISH=CLI Configuration executing on
ICX {devname} - {mgmt_ip} is completed: Total cli commands {all_num},
success {suc_num}, fail {fail_num} |
Warning |
Examine the reason for failure. Retry with correct CLI
commands. |
The CLI configuration process on specific ICX switch is
completed, displaying the total number of CLI commands executed with the
count of successful and failed commands. |