config
|
From the Linux shell, this command provides access to the command line configuration
utility.
|
No parameters.
[ <serviceacctlogin@<hostname>]$ c onfig
|
config admin-access allow-all
|
Clears restrictions to the administrative functionality so that an administrator can
access the Cloudpath Admin UI from any IP address.
|
No parameters.
config admin-access allow-all
|
config admin-access restrict
|
Restricts which IP addresses have administrative access to the Cloudpath Admin UI.
|
[Comma separated list of IP addresses/CIDR]
config admin-access restrict 1 72.16.4.20, 172.16.5.18
or
config admin-access restrict 172.16.4.20/24
|
config hostname
|
Sets the hostname.
|
[This system's network name (FQDN)]
config hostname test22.company.net
|
config hostname-restricted allow-all
|
Requests by IP address are not blocked.
|
No parameters
config hostname-restricted allow-all
|
config hostname-restricted restrict
|
Requests that do not match the hostname are blocked.
|
No parameters
config hostname-restricted restrict
|
config https enable
|
Sets whether the Apache server should be run as HTTP or HTTPS.
|
[The HTTPs port to use]
config https enable 55
|
config https disable
|
Sets whether the Apache server should be run as HTTP or HTTPS.
|
No parameters
config https disable
|
config https-servername default
|
Uses the system's hostname (FQDN).
|
No parameters
config https-servername default
|
config https-servername override
|
Set the HTTPS server name. This is typically used when operating behind a load balancer.
|
[This system's network name]
config https-servername test22.company.net
|
config network DHCP
|
Configures whether you want DHCP to assign network IP addresses.
|
[
true to use DHCP,
false to use STAT IC IP addresses]
config network DHCP true
This command causes the system to toggle the eth0 and loopback interfaces.
|
config network restart
|
Restarts the network after making configuration changes to DHCP settings.
|
No parameters
config network restart
|
config network STATIC dns
|
Configures the STATIC IP addresses for the DNS server.
|
[IP address of the DNS server]
config network STATIC dns 1 72.16.4.202
|
config network STATIC ip
|
Configures the STATIC IP addresses for the system's eth0 interface, subnet mask, and
gateway.
|
[IP address, subnet mask, and gateway for the eth0 interface]
config network STATIC ip 172.16.6.35 255.255.252.0 172.16.4.1
|
config ntp
|
Sets the NTP server
|
[IP address of the NTP server]
config ntp 172.16.2.106
|
config ntp sync-now
|
Forces an ntpdate to the configured NTP server.
|
[hostname for shared db]
config ntp sync-now
|
config proxy set
|
Sets the HTTP proxy. Requires a reboot.
The HTTP port and HTTPS port must be the same. This is the port number for the HTTP
proxy tunnel.
The [proxy-bypass-hosts] parameter (optional) is a comma-separated list of hosts
that should bypass the proxy.
Use the
config clear-proxy command to remove the configuration
|
[HTTP hostname] [HTTPport] [HTTPS hostname] [HTTPS port] [proxy- bypass-hosts]
config proxy hostA 80 hostB 80 hostC,hostD
|
config proxy remove
|
Removes the HTTP proxy
|
No parameters
config proxy remove
|
config ssh enable
|
Enables SSH access. The default port is 8022, or you can select port 22.
|
[SSH port ]
config ssh enable
or
config ssh enable 22
|
config ssh disable
|
Disables SSH access.
|
[SSH port ]
config ssh disable
|
config sslv3 allow
|
Permits SSLv3 protocol on HTTPS connections.
|
No parameters
config sslv3 allow
|
config sslv3 block
|
Prevents SSLv3 protocol on HTTPS connections
|
No parameters
config sslv3 block
|
config timezone
|
Sets the timezone to be used.
|
[Zone name]
config timezone
This command displays a list of acceptable timezones.
When prompted, enter the desired timezone as shown.
America/Denver
Alternately, you can enter the correct timezone as part of the command.
config timezone America/Denver
|