Find Technical Content
  • Home
  • Ruckus Support Portal
  • Ruckus Networks
  • Table of Contents
  • Dark Mode

Powered by Titania Delivery

⚠ This cached page may be outdated. Click refresh to get the latest content.
Cached Version You are Offline

You are viewing a cached version of this page.

You are currently offline. This page was loaded from cache.

IPv6 Multicast

  • 1 IPv6 Multicast Protocols
    • 1.1 IPv6 PIM Sparse
      • 1.1.1 Layer 3 IPv6 Multicast Scaling Numbers
      • 1.1.2 IPv6 PIM Sparse Router Types
      • 1.1.3 RP Paths and SPT Paths
      • 1.1.4 RFC 3513 and RFC 4007 Compliance for IPv6 Multicast Scope-based Forwarding
      • 1.1.5 IPv6 PIM Sparse Configuration
      • 1.1.6 Enabling IPv6 PIM Sparse
      • 1.1.7 Enabling IPv6 PIM Sparse on a Virtual Ethernet Interface
      • 1.1.8 Enabling IPv6 PIM Sparse on a Specific VRF
      • 1.1.9 Modifying IPv6 PIM Options
      • 1.1.10 Configuring the Slow Path Forwarding of IPv6 Multicast Data Packets
      • 1.1.11 Configuring BSRs and RPs for IPv6 PIM Sparse
      • 1.1.12 Configuring BSRs and RPs for IPv6 PIM Sparse for a Specified VRF
      • 1.1.13 Updating IPv6 PIM-Sparse Forwarding Entries with New RP Static Configuration
      • 1.1.14 Embedded Rendezvous Point
      • 1.1.15 Source-Specific Multicast with IPv6 PIM
        • 1.1.15.1 Configuring IPv6 PIM Source-Specific Multicast
      • 1.1.16 Configuring a DR Priority
      • 1.1.17 Passive Multicast Route Insertion
        • 1.1.17.1 Viewing PMRI Status and Disabling PMRI
      • 1.1.18 Clearing the IPv6 PIM Traffic Counters and Forwarding Cache
      • 1.1.19 Defining the Maximum Number of IPv6 PIM Cache Entries
      • 1.1.20 Configuring a Static Multicast Route Within a VRF
      • 1.1.21 Configuring the Route Precedence by Specifying the Route Types
      • 1.1.22 Configuring IPv6 PIM Neighbor Filtering
      • 1.1.23 IPv6 PIM Join and Prune Policy
        • 1.1.23.1 Configuring IPv6 PIM Join and Prune Policy
    • 1.2 IPv6 PIM Convergence on MAC Address Movement
    • 1.3 IPv6 PIM Anycast RP
      • 1.3.1 Configuring IPv6 PIM Anycast RP
    • 1.4 Displaying IPv6 PIM Information
    • 1.5 Multicast Listener Discovery and Source-specific Multicast Protocols
      • 1.5.1 Enabling MLDv2
      • 1.5.2 Configuring MLD Options for Default and Non-Default VRFs
      • 1.5.3 Configuring MLD Options on Interfaces
      • 1.5.4 Configuring the MLD Report Filter Policy
      • 1.5.5 Setting the Maximum Number of MLD Group Addresses
      • 1.5.6 IPv6 PIM Register Message Rate Limit
        • 1.5.6.1 Configuring the Register Message Rate Limit for PIMv6
      • 1.5.7 IPv6 PIM Register Message Filter Rule
        • 1.5.7.1 Configuring the Register Message Filter Rule for PIMv6
      • 1.5.8 Multicast Non-Stop Routing
      • 1.5.9 Specifying Multiple Static Multicast Groups
      • 1.5.10 Clearing MLD Traffic Counters and IPv6 PIM Group Membership Table Cache
      • 1.5.11 Displaying IPv6 MLD Information
    • 1.6 IPv6 Multicast Boundaries
      • 1.6.1 Configuration Considerations for IPv6 Multicast Boundaries
      • 1.6.2 Configuring IPv6 Multicast Boundaries
      • 1.6.3 ACL to Permit IPv6 Multicast Traffic
      • 1.6.4 ACL to Deny IPv6 Multicast Traffic

IPv6 Multicast Protocols

In this section:

  1. IPv6 PIM Sparse
  2. IPv6 PIM Convergence on MAC Address Movement
    IPv6 PIM convergence occurs when the IPv6 PIM module is notified of a topology change.
  3. IPv6 PIM Anycast RP
  4. Displaying IPv6 PIM Information
    You can use various show commands to view information about IPv6 PIM.
  5. Multicast Listener Discovery and Source-specific Multicast Protocols
  6. IPv6 Multicast Boundaries

Did you find what you were looking for?

Thanks!

Ruckus Wireless

© 2026 Ruckus Wireless LLC All rights reserved.

  • Accessibility
  • Privacy & Cookies
  • Do Not Sell My Information
  • Trademarks
  • Terms
  • Feedback