-
tunnel vrf
Last Updated
Sep 03, 2026
only supported on IPsec tunnel interfaces. The mode of the VTI must be set to ipsec before executing this command. ICX 7150 devices do not support tunnels. The no form of the command removes the base VRF configuration for the VTI. The following example shows how to configure a VRF named blue as the
-
Assigning OSPFv2 areas
Last Updated
Sep 03, 2026
Assigning OSPFv2 areas Assigning OSPFv2 areas Assigning OSPFv2 areas Areas can be assigned as OSPFv2 areas. For the ICX 7150, a maximum of 4 OSPF areas is supported for each OSPF instance. Enter the configure terminal command to access global configuration mode. device# configure terminal Enter the
-
IPv6 Over IPv4 Tunnels
Last Updated
Sep 03, 2026
mechanism requires that the Layer 3 switch at each end of the tunnel run both IPv4 and IPv6 protocol stacks. The Layer 3 switches running both protocol stacks, or dual-stack routers, can interoperate directly with both IPv4 and IPv6 end systems and routers. Refer to the "IPv4 and IPv6 protocol stacks" section. ICX 7150 devices do not support tunnels.
-
show lrm-adapter ethernet
Last Updated
Sep 03, 2026
show lrm-adapter ethernet show lrm-adapter ethernet show lrm-adapter ethernet Displays the LRM adapter parameters. show lrm-adapter ethernet { stackid/slot/port } User EXEC mode The command is available only for ICX 7150 and ICX 7550 10G access ports. The command is available only for RUCKUS ICX
-
Multi-VRF Support for DAI
Last Updated
Sep 03, 2026
enable DAI on individual VLANs and assign any interface as the ARP inspection trust interface. If an interface is a tagged port in this VLAN, you can turn on the trust port per VRF, so that traffic intended for other VRF VLANs will not be trusted. ICX 7150 devices do not support VRFs. Complete the
-
RUCKUS FastIron Layer 3 Routing Configuration Guide, 10.0.10
Last Updated
Sep 03, 2026
can enable DAI on individual VLANs, and assign any interface as the ARP inspection trust interface. If an interface is a tagged port in this VLAN, you can turn on the trust port per VRF, so that traffic intended for other VRF VLANs will not be trusted. Ruckus ICX 7150 and 8100 devices do not support
-
Configuring a tunnel as next hop
Last Updated
Sep 03, 2026
configuring an IPv6 address or explicitly enabling IPv6 on that interface. ICX 7150 devices do not support tunnels. To configure a basic IPv6 static route through a next-hop tunnel, perform these steps. Enter global configuration mode. device# configure terminal Enter the IPv6 destination address and
-
Configuring a Tunnel as Next Hop
Last Updated
Sep 03, 2026
configuring an IPv6 address or explicitly enabling IPv6 on that interface. ICX 7150 and ICX 8100 devices do not support tunnels. To configure a basic IPv6 static route through a next-hop tunnel, perform these steps. Enter global configuration mode. device# configure terminal Enter the IPv6 destination
-
tunnel destination
Last Updated
Sep 03, 2026
IPv4 address of an interface. ipv6-address Specifies the IPv6 address of the destination. Interface tunnel configuration mode ICX 7150 devices do not support tunnels. You must ensure that a route to the tunnel destination exists on the tunnel source device and create a static route if necessary. The
-
tunnel mode ipsec
Last Updated
Sep 03, 2026
packets transmitted over the tunnel. ipv6 Specifies the application of IPsec protection for IPv6 packets transmitted over the tunnel. Tunnel interface configuration mode IPsec is supported only on ICX 7450 devices. ICX 7150 devices do not support tunnels. The no form of the command removes the IPsec