Changing PE IDs with SPX Interactive-setup
SPX interactive-setup makes changing PE IDs simpler.
Note: The new PE ID can be any ID including an existing or provisional PE ID. The exception
is an ID that causes a module mismatch.
- Use the
show running-configcommand to verify that the CB is enabled and to check SPX port and LAG configurations.ICX7750-48F Router(config)# show running-config Current configuration: ! ver 08.0.50b1T203 ! stack unit 1 module 1 icx7750-48-xgf-port-management-module module 2 icx7750-qsfp-6port-qsfp-240g-module module 3 icx7750-6q-6port-qsfp-240g-module spx unit 17 module 1 icx7250-24-port-management-module module 2 icx7250-sfp-plus-8port-80g-module spx-port 17/2/4 spx-lag 17/2/5 to 17/2/6 17/2/8 spx unit 18 module 1 icx7250-24-port-management-module module 2 icx7250-sfp-plus-8port-80g-module spx-port 18/2/3 spx-lag 18/2/5 to 18/2/6 18/2/8 ! !
spx cb-enable spx cb-configure zero-touch-enable spx-port 1/1/3 spx-port 1/1/16 zero-touch-ports 1/1/3 to 1/1/16 pe-id 1/1/3 18 17 1/1/16 ! ! no inline power non-pd-detection enable ip ssl min-version tls_1_1 ! ! interface management 1 ! ! end
In this example, theshow running-configcommand indicates that the CB is already enabled. The zero-touch utility is also enabled and must be disabled. Two CB SPX ports (1/1/3 and 1/1/16) are configured, and a range of ports are identified by thezero-touch-portsconfiguration to detect new PE candidates. Two PEs, 17 and 18, are attached to the CB (a standalone ICX 7750). - If necessary, disable the zero-touch utility.
ICX7750-48F Router(config-spx-cb)# no zero-touch-enable <-- You cannot run spx interactive- setup when zero-touch is enabled. ICX7750-48F Router(config-spx-cb)# end
In the example, the zero-touch utility is disabled as a precursor to enabling interactive-setup. - In Privileged EXEC mode, enable the spx interactive-setup utility.
ICX7750-48F Router# spx interactive-setup You can abort spx interactive-setup at any stage by <ctrl-c> 0: quit 1: change PE IDs 2: discover and convert new units (no startup-config flash) to PEs 3: discover and convert existing/new standalone units to PEs 2&3 can also find new links and convert chain(s) to ring.
The example shows the options available when you start the interactive-setup utility. - When prompted, type "1" to change PE IDs.
- When prompted, type the new ID for each PE unit. After you complete your entry, type
done. If you do not want to change the ID of a particular PE, press the Enter key. At
the end of the PE list, you are prompted to confirm or cancel your entries.
Note: A PE ID can be changed to any legitimate ID, even if it is used by an existing PE. For example, you can swap two IDs. There are a few exceptions:
- The module configuration of the new ID must either be empty or match the PE.
- SPX port or LAG configuration, including speed configuration, must match.
If you try to change a PE ID using an existing ID or provisional PE ID with a module mismatch, the ID selection is blocked, and SPX interactive-setup prints a warning similar to the following message.
Error! PE21 --> 51 requires same modules or no PE51 configuration. Allowed IDs: 18,21,26-29,33-39,42-49,52-56
If you select an existing or provisional ID that would result in an SPX port or SPX LAG configuration mismatch, the system blocks the configuration and displays a warning similar to the following message.
Error! PE21 --> 23 requires same spx-port/lag or no PE23 configuration. Allowed IDs: 18,21,26-29,33-39,42-49,52-56
If you select an existing or provisional ID that would result in an SPX port or SPX LAG speed mismatch, the system blocks the configuration and displays a warning similar to the following message.
Error! PE21 --> 32: Port 21/2/2 and 32/2/2 have different speed configuration. Allowed IDs: 18,21,26-29,33-39,42-49,52-56
Note: After a PE is re-numbered, the old configuration still exists if it is a static unit. The system does not convert the old configuration to the new IDs. For example, if PE 20 changes its ID to 30, the system does not move interface 20/1/1 configuration to interface 30/1/1. - Type
y to confirm your changes.
You do not need to physically detach or un-configure any unit. The system temporarily disables any SPX ports or LAGs necessary to detach the affected PE units. After a few seconds, the ports are re-enabled, allowing the PEs to join with new PE IDs.
Type "done" to finish, or a new ID for PE 18 (default 18): 23 Type "done" to finish, or a new ID for PE 17 (default 17): 24 Change IDs: 18->23, 17->24, Do you want to proceed? (enter 'y' or 'n'): y T=14m43.4: Sending new IDs to PE(s) 17-18... power down ports to detach PEs: 1/1/3 1/1/16 power up ports: 1/1/3 1/1/16. Affected PEs will join with new IDs. Exit spx interactive-setup, reason: done ID changes Sica Unit id:24, PoD License Capacity:8 Stack unit 24 Power supply 1 is up Stack unit 24 Power supply 2 is down Sica Unit id:23, PoD License Capacity:8 Stack unit 23 Power supply 1 is up Stack unit 23 Power supply 2 is down sh spx T=17m13.2: alone: standalone, D: dynamic cfg, S: static ID Type Role Mac Address Pri State Comment 1 S ICX7750-48XGF alone cc4e.24d2.2c00 0 local Ready 23 D ICX7250-24 spx-pe cc4e.24dc.e9ce N/A remote Ready 24 D ICX7250-24 spx-pe cc4e.24dc.f166 N/A remote Ready +---+ 2/1| 1 |2/4 +---+ +----+ +----+ 1/1/3--2/3| 23 |2/5==2/5| 24 |2/4--1/1/16 +----+ +----+The example changes the ID for PE 18 to 23 and the ID for PE 17 to 24. At the end of the process, the SPX configuration is displayed, showing the new PE IDs. - Execute the
write memorycommand to save the configuration.
The following example uses the SPX interactive-setup utility to change two existing PE IDs.
ICX7750-48F Router# configure terminal ICX7750-48F Router(config)# show running-config Current configuration: ! ver 08.0.50b1T203 ! stack unit 1 module 1 icx7750-48-xgf-port-management-module module 2 icx7750-qsfp-6port-qsfp-240g-module module 3 icx7750-6q-6port-qsfp-240g-module spx unit 17 module 1 icx7250-24-port-management-module module 2 icx7250-sfp-plus-8port-80g-module spx-port 17/2/4 spx-lag 17/2/5 to 17/2/6 17/2/8 spx unit 18 module 1 icx7250-24-port-management-module module 2 icx7250-sfp-plus-8port-80g-module spx-port 18/2/3 spx-lag 18/2/5 to 18/2/6 18/2/8 ! ! spx cb-enable spx cb-configure zero-touch-enable spx-port 1/1/3 spx-port 1/1/16 zero-touch-ports 1/1/3 to 1/1/16 pe-id 1/1/3 18 17 1/1/16 ! ! no inline power non-pd-detection enable ip ssl min-version tls_1_1 ! ! interface management 1 ! ! end ICX7750-48F Router(config)# spx cb-config ICX7750-48F Router(config-spx-cb)# no zero-touch-enable <-- You cannot run spx interactive- setup when zero-touch is enabled. ICX7750-48F Router(config-spx-cb)# end ICX7750-48F Router# spx interactive-setup You can abort spx interactive-setup at any stage by <ctrl-c> 0: quit 1: change PE IDs 2: discover and convert new units (no startup-config flash) to PEs 3: discover and convert existing/new standalone units to PEs 2&3 can also find new links and convert chain(s) to ring. Please type your selection: 1 +----+ +----+ 1/1/3--2/3| 18 |2/5==2/5| 17 |2/4--1/1/16 +----+ +----+ Type "done" to finish, or a new ID for PE 18 (default 18): 23 Type "done" to finish, or a new ID for PE 17 (default 17): 24 Change IDs: 18->23, 17->24, Do you want to proceed? (enter 'y' or 'n'): y T=14m43.4: Sending new IDs to PE(s) 17-18... power down ports to detach PEs: 1/1/3 1/1/16 power up ports: 1/1/3 1/1/16. Affected PEs will join with new IDs. Exit spx interactive-setup, reason: done ID changes Sica Unit id:24, PoD License Capacity:8 Stack unit 24 Power supply 1 is up Stack unit 24 Power supply 2 is down Sica Unit id:23, PoD License Capacity:8 Stack unit 23 Power supply 1 is up Stack unit 23 Power supply 2 is down sh spx T=17m13.2: alone: standalone, D: dynamic cfg, S: static ID Type Role Mac Address Pri State Comment 1 S ICX7750-48XGF alone cc4e.24d2.2c00 0 local Ready 23 D ICX7250-24 spx-pe cc4e.24dc.e9ce N/A remote Ready 24 D ICX7250-24 spx-pe cc4e.24dc.f166 N/A remote Ready +---+ 2/1| 1 |2/4 +---+ +----+ +----+ 1/1/3--2/3| 23 |2/5==2/5| 24 |2/4--1/1/16 +----+ +----+ ICX7750-48F Router# write memory