Search Results: "icx 7550"

PoE/PoE+ - Power over Ethernet PoE/PoE+ - Power over Ethernet PoE/PoE+ - Power over Ethernet Feature Legacy inline power is not supported in 4-pair PoE ports. ICX 7150 ICX 7150-ES ICX 7550 ICX 7650 ICX 7850 ICX 8100 ICX 8200 Auto PoE firmware upgrade 08.0.70 10.0.10d 08.0.95 08.0.70 No 10.0.10f

BGP4 - IPV4 Border Gateway Protocol BGP4 - IPV4 Border Gateway Protocol BGP4 - IPV4 Border Gateway Protocol Feature ICX 7550 ICX 7650 ICX 7850 ICX 8100 ICX 8200 BGP4 08.0.95 08.0.70 08.0.90 No 10.0.20a BGP4 Graceful Restart 08.0.95 08.0.70 08.0.90 No 10.0.20a BGP4 Graceful Restart helper mode

ECMP Load Sharing Paths per Device ICX 7550 / ICX 8200 ICX 7650 / ICX 7850 8 32 For optimal results, set the maximum number of paths to a value at least as high as the maximum number of equal-cost paths your network typically contains. For example, if the Layer 3 switch you are configuring for IP load

configure the device to monitor a different port for packet drops. On the ICX 7550, ICX 7650, ICX 7850, ICX 8100, and ICX 8200 devices, each port has its own set of drop counters. This task is supported only on the ICX 7150 and ICX 7150-ES models. Perform the following steps to configure a port that the

31-Bit Subnet Masks on Point-to-Point Networks 31-Bit Subnet Masks on Point-to-Point Networks 31-Bit Subnet Masks on Point-to-Point Networks 31-bit subnet masks are supported on ICX 7150, ICX 7250, ICX 7450, ICX 7550, ICX 7650, and ICX 7850 devices running the full Layer 3 image. To conserve IPv4

Layer 2 loop detection protocols. Suppressing the link status notification allows a quick port status change and recovery to occur without triggering any of the changes that are necessary when a port stays down. By default, the delay time is not configured. Configuring delayed Layer 3 notifications on the VE feature is supported on ICX 7150, ICX 7250, ICX 7450, ICX 7550, ICX 7650, and ICX 7850 product families from RUCKUS.

. MACsec commands are supported on ICX 7450, ICX 7550, ICX 7650, and ICX 7850 devices. For a MACsec channel to be created between two ports, both ports and devices designated must have MACsec enabled and configured. The enable-mka ethernet command enables MACSec licensing on the specified interface

a slot or interface. Note that for the ICX 7550, whenever the speed is changed on a EEE-enabled multi-gigabit port, the clear eee-statistics command must be executed before displaying EEE statistics using the show eee-statistics ethernet command. The show eee-statistics ethernet command displays the

command. The MAC address movement notification triggers a notification to the IPv6 PIM module, which results in convergence. IPv6 PIM convergence is supported only in IPv6 PIM Sparse mode and is not supported in IPv6 PIM Dense mode. IPv6 PIM convergence on MAC address movement is supported on RUCKUS ICX

7250, ICX 7450, ICX 7550, ICX 7650, and ICX 7850 devices. IPv6 PIM convergence on MAC address movement is applicable only when the multicast source and IPv6 PIM routers are in the same Layer 2 domain.