⚠ This cached page may be outdated. Click refresh to get the latest content.
Cached Version You are Offline

You are viewing a cached version of this page.

You are currently offline. This page was loaded from cache.

Search Results: "icx 7150"

Showing 1,021 - 1,030 of 1,714 results

Relevance: best match to your search term first.

  • Disabling the Flooding of Unregistered IPv4 Multicast Frames in an IGMP-Snooping-Enabled VLAN

    Last Updated Sep 03, 2026

    (standalone and stacking) RUCKUS ICX 7250 (standalone and stacking) RUCKUS ICX 7150 (standalone and stacking) Support for this feature on the RUCKUS ICX 7750 was introduced in FastIron 8.0.10d. In releases prior to FastIron 8.0.30, support for this feature on the RUCKUS ICX 7750 was for devices in

  • Creating an IP Static Route in a Non-Default VRF

    Last Updated Sep 03, 2026

    Creating an IP Static Route in a Non-Default VRF Creating an IP Static Route in a Non-Default VRF Creating an IP Static Route in a Non-Default VRF You can configure an IP static route in a non-default VRF. If the VRF is not named, the default VRF is used. The VRF configured must be a valid VRF. ICX

  • Switch Port Extender and IP Multicast

    Last Updated Sep 03, 2026

    connected to the CB in a chain or ring can be ICX 7450, ICX 7250, ICX 7150 units, or a mix of these units. Multicast E-CID and IEE 802.1BR The point-to-multipoint E-channels used for remote replication are identified by an E-CID with a value in the range of 0x1000 to 0x3FFF (values less than this are reserved for E-CIDs associated with point-to-point E-channels).

  • Configuring a VRF as next hop for an IPv6 static route

    Last Updated Sep 03, 2026

    enable the forwarding of IPv6 traffic on the Layer 3 switch using the ipv6 unicast-routing command and enable IPv6 on at least one interface by configuring an IPv6 address or explicitly enabling IPv6 on that interface. ICX 7150 devices do not support VRFs. The VRF designated in the procedure must

  • What’s new in this document

    Last Updated Sep 03, 2026

    What’s new in this document What’s new in this document What’s new in this document Per Technical Support Bulletin TSB 2022-005 - Starting with release 8.0.95h/9.0.10d, products running a newer Power Over Ethernet (PoE) chipset do not support older releases, the POE functionality in ICX 7150 and

  • ACL Logging Upgrade Considerations

    Last Updated Sep 03, 2026

    the respective bindings corresponding to the filter group and interface combination in the ingress direction after the upgrade. On RUCKUS ICX 7150, ICX 7550, ICX 7650, and ICX 7850 devices, ACL logging is not supported for ACLs applied to outbound traffic.

  • Configuration Notes for ACL Logging

    Last Updated Sep 03, 2026

    and VLANs. If you remove an egress ACL with rules enabled for logging, although new packets are not logged, previous logs will be in the syslog when the sample timer expires. The log count may not be accurate for broadcast traffic or for unknown unicast traffic. On RUCKUS ICX 7150, RUCKUS ICX 7550

  • Campus Fabric Topology Overview

    Last Updated Sep 03, 2026

    ICX 7650, ICX 7750, or ICX 7850 units connected in a linear or ring topology. PE units are specially configured ICX 7450, ICX 7250, or ICX 7150 units that are connected to the CB. The PE units can be connected to each other over a single SPX port or LAG to form a PE chain or ring. The PE chain or

  • Device Overview

    Last Updated Sep 02, 2026

  • Monitoring the Device

    Last Updated Sep 02, 2026