Multi-Chassis Trunking

• 1 Multi-Chassis Trunking
  • 1.1 Multi-Chassis Trunking Overview
    • 1.1.1 How MCT Works
    • 1.1.2 MCT Terminology
    • 1.1.3 MCT Data Flow
    • 1.1.4 MCT and VLANs
    • 1.1.5 MCT Feature Interaction and Supported Features
    • 1.1.6 MCT Board Type Compatibility
  • 1.2 Basic MCT Configuration
    • 1.2.1 MCT Configuration Considerations
    • 1.2.2 Differences in Configuring MCT for the Switch and Router Image
    • 1.2.3 MCT Recommendations and Best Practices
    • 1.2.4 Configuring MCT
      • 1.2.4.1 Step 1: Configure ICL for Cluster Devices and LAGs for Client Devices
      • 1.2.4.2 Step 2: Configure the MCT VLAN, MCT Session VLAN, Recommended MCT Keep-Alive VLAN, and ICL Forwarding Delay
      • 1.2.4.3 Step 3: Configuring the Cluster
      • 1.2.4.4 Step 4: Configuring Clients
    • 1.2.5 Forcing a Port Up in a Basic MCT Configuration
  • 1.3 Cluster Client Automatic Configuration
    • 1.3.1 Setting Up Cluster Client Automatic Configuration
  • 1.4 MCT Failover Scenarios
    • 1.4.1 Cluster Failover Mode
      • 1.4.1.1 Configuring the Failover Mode
    • 1.4.2 Client Isolation Mode
      • 1.4.2.1 Configuring Client Isolation Mode
    • 1.4.3 Shutting Down All Client Interfaces
    • 1.4.4 Using the Keep-Alive VLAN
    • 1.4.5 Setting Keep-Alive Timers and Hold Time
  • 1.5 MCT Hitless Upgrade
  • 1.6 Layer 2 Behavior with MCT
    • 1.6.1 Dynamic Trunks (LAGs)
    • 1.6.2 Port Loop Detection
    • 1.6.3 MCT Layer 2 Protocols
    • 1.6.4 Layer 2 Multicast Snooping over MCT
      • 1.6.4.1 IGMP and MLD Snooping
      • 1.6.4.2 IGMP and MLD Snooping Behavior on MCT Cluster Devices
      • 1.6.4.3 How Failovers are Handled for Layer 2 Multicast over MCT
      • 1.6.4.4 PIM-SM and PIM6-SM Snooping over MCT
      • 1.6.4.5 Forwarding Entries for PIM-SM and PIM6-SM Multicast Snooping
      • 1.6.4.6 Displaying Information for Multicast Snooping
      • 1.6.4.7 Multicast Snooping Configuration Example
  • 1.7 Layer 3 Behavior with MCT
    • 1.7.1 Layer 3 Unicast Forwarding over MCT
      • 1.7.1.1 Layer 3 Traffic Forwarding Toward MCT Clients
      • 1.7.1.2 Layer 3 Traffic Forwarding From MCT Clients
    • 1.7.2 User-defined VRF Support over MCT
    • 1.7.3 VRRP or VRRP-E over an MCT-Enabled Network
    • 1.7.4 OSPF and BGP over an MCT-Enabled Network
    • 1.7.5 Layer 3 with MCT Configuration Considerations
    • 1.7.6 MCT Configuration for a Single-Level MCT Deployment
      • 1.7.6.1 MCT Configuration: Router A
      • 1.7.6.2 MCT Configuration: Router B
      • 1.7.6.3 MCT Configuration: S1-SW Device
    • 1.7.7 MCT Configuration with VRRP-E
      • 1.7.7.1 VRRP-E Configuration: Router A
      • 1.7.7.2 VRRP-E Configuration: Router B
    • 1.7.8 MCT Configuration with OSPF
    • 1.7.9 MCT Configuration with BGP
    • 1.7.10 PIM Over MCT Intermediate Router Functionality
      • 1.7.10.1 MCT Peer as Intermediate Upstream Router
      • 1.7.10.2 MCT Peer as Intermediate Downstream Router
      • 1.7.10.3 Load Sharing of Multicast Traffic by MCT-Cluster on CCEP Links
      • 1.7.10.4 Fast Convergence of Multicast Traffic
      • 1.7.10.5 First Hop and Last Hop Router Support on MCT Cluster Devices for MCT VLANs
      • 1.7.10.6 RP Support on MCT Cluster Devices
      • 1.7.10.7 Anycast RP Support for MCT Cluster Devices
      • 1.7.10.8 Requirements for Multicast MCT
      • 1.7.10.9 Limitations
      • 1.7.10.10 Configuring Multicast Routing over MCT for IPv4
  • 1.8 Displaying MCT Information
    • 1.8.1 MAC Clear Commands
  • 1.9 Single-Level MCT Configuration Example
    • 1.9.1 Client 1 Configuration
    • 1.9.2 Client 2 Configuration
    • 1.9.3 AGG-A (R1) Configuration
    • 1.9.4 AGG-B (R2) Configuration
  • 1.10 Two-Level MCT Configuration Example
    • 1.10.1 AGG-A (R1) Configuration
    • 1.10.2 AGG-B (R2) Configuration
    • 1.10.3 DIST-A (R3) Configuration
    • 1.10.4 DIST-B (R4) Configuration
  • 1.12 MCT Configuration Example Using ICX 7850 Stacks as Cluster Peers
  • 1.13 MCT Hitless Sequential Upgrade